AVANTONE MIXCUBES ACTIVE STUDIO MONITORS WHITE -PAIR-

Avantone Active MixCubes Powered Full-Range Mini Reference Monitors

The Avantone MixCubes are shielded, full-range mini reference monitors. Their design is inspired by the legacy of the 5C Sound Cubes used in virtually all-major studios for the last 25 years.

Application
Active Recording / Mixdown Monitors

Engineering Objective
The Avantone Active Mixcubes are designed to be high-resolution, full-range powered mini-reference monitors for fixed or remote locations.
The secondary engineering facet was to create a timeless design that compliments a single full-range transducer.

Performance Objective
Studios primarily use 2-way & 3-way larger monitors designed to represent a wide range reference viewpoint at higher listening levels. However, in this newly developing age of High Definition Audio, there is still a need to also hear what your mix will sound like when played back over small "bass-challenged" systems such as televisions, clock radios, computers, car stereos, iPod docking stations, etc. It is important to make mixing judgments based partially on listening to reference monitors that will not impart tonal anomalies caused by crossovers or inferior full range drivers. Particular attention is always paid to the critical mid-range vocal/guitar/keyboard areas. This is where having a full-range monitor without a crossover is truly revealing. Ten months of R&D comparative listening & tweaking went into the voicing of the AVANTONE MixCubes. The result is a very smooth sounding, full range upgrade from the original 5C Sound Cubes. Listening tests reveal that the MixCubes have a smooth, more open, transparent top end response with extended bass while maintaining their basic original character.

Cabinet Design
The original 5C Sound CubesTM were made of ½" particleboard covered with a glue-on wood grain contact paper. We chose to use thicker, denser MDF board because of its high rigidity and inherent low-resonance characteristics. We started with a 165mm (6 1/2“) sealed cube design with radiused edges. We then chose an elegant Polyurethane high gloss "RETRO-CREAM" finish. The originals had either screws or on later models plastic binding posts mounted on a recessed plastic cup. We upgraded to high-end nickel plated, machined solid metal binding posts (Dual banana spacing) mounted on a black anodized ,milled and silk-screened aluminum terminal plate. Next we added a 7mm thick neoprene pad embedded into the base of the cabinet to serve as a skid-resistant acoustic isolator. Additionally, for creative mounting situations, we recessed an industry standard 5/8“-27 mic stand mount into the base.

Driver Design
The originals were a basic 5" stamped frame design. We designed a proprietary 5.25" die cast aluminum frame driver/cone assembly to exceed the performance of the originals. The mounting bezel is then polished for an elegant appearance. The paper cone, chosen for its musical character, is custom designed & crafted using the finest New Zealand pulp with mica fibers added for lighter weight & rigidity. The cloth surround is made in Japan to exacting uniform thickness tolerances. The Top Plate and T-Yoke of driver are made of Sumitomo 1008 low carbon steel enabling the highest modeled flux density in the gap. The magnets are Y- 40 GRADE (MIL-SPEC) yielding a 43oz. High Power-low distortion motor structure.

Amplifier Design
We designed the amp module from the ground up to be a true professional-grade amplifier. It incorporates "overkill" concepts in component selection as well as safety. The result is a "no-compromise" amp with robust headroom characteristics that will rival the performance of much higher priced studio rack mount amps.

System Type
Active (Self-powered) shielded full-range stereo pair  

Frequency Response
90Hz - 17,000Hz (useful musical range)

>Driver Impedance
Nominal 8 ohms

Max SPL
104db @ 1 meter = 1%THD (PINK NOISE)

Amplifier Type
Class A/B

Amplifier Power
60 watts RMS@ .005% THD (1KHz)

Amp Frequency Response
22Hz-50KHz +0dB/- 3dB (90Hz-50KHz +/-0dB)

Noise
S/N -113 dB

Sensitivity
0dBu (.775VRMS) input at maximum volume (+6dB) = 104dB SPL

Driver
Proprietary design 5.25" cast aluminum frame / paper cone / shielded

Cabinet
sealed / 18mm MDF / Dacron acoustical stuffing

Inputs
XLR & TRS (COMBO JACK) +4/Balanced and -10 unbalanced

Weight
7 lb 5 oz (per speaker)

Dimensions
165mm x 165mm x 165mm (6 1/2" x 6 1/2" x 6 1/2" in)

Features
Ruler-Flat Response 52Hz to 20kHz, + 1.5 dB

Benefit: Sound true to actual recording

Benefit: Any pair of speakers is a matched pair

Active Technology

2 FR (Fast Recovery) Series Amplifiers; HF 40W; LF 100W

Benefit: Precise dividing slope, correct phase, and low distortion

Benefit: Minimal chance of speaker damage due to overdriving

Servo Loop Woofer Technology

Electronic control and dampening

Benefit: Speaker output is as true to incoming signal as possible

Frequency Response Controls

80Hz low-cut switch; 3-position live/dead switch (-2bdB, Normal and +2dB)

Benefit: Excellent response in a variety of acoustic environments

Wide Sweet Spot

Custom-designed die-cast wave guide

Benefit: User hears the same thing across a wider range of motion

3-Position Acoustic Space Switch

Compensation in bass response for half-space (-2dB) and quarter-space (-4dB) placement

Benefit: As close-to-flat performance as possible regardless of placement in room

Applications
Professional Recording Studios

Home and Project Studios

Film (THX) and Post Production Studios

Home Theater Installations

Acoustic Performance
Free Field Frequency Response: 52Hz - 20Hz

PRICE PER UNIT

The most powerful AX monitor

With its power and radiation characteristics, the brand new A8X is suitable for both nearfield and midfield monitoring. With a price/performance ratio that could hardly be better, this monitor is a perfect entry into these monitoring fields.

The A8X is equipped with the X-ART tweeter and a large (8.5”) midwoofer, a combination that adds both a very deep and yet very tight bass response to the unsurpassed reproduction qualities of the ADAM proprietary tweeter: a licence to thrill.

Cabinet- and bass reflex-construction

Like the other AX-Series models, the upper corners of the A8X are slanted to minimize reflections. The very large, double bass reflex tubes on the front have been specifically designed to perfectly match the midwoofer with its large voice coil.

Amplification and controls

With a 50W A/B amplifier for the tweeter and a 150W PWM amplifier for the midwoofer, the A8X has power in abundance and is the brawny monitor of the AX-Series.

On the rear panel are several controls: a gain for the high frequencies (± 4dB) and two shelf filters for the high and low frequencies.
There are both XLR (balanced) and RCA (unbalanced) connectors on the rear panel of the speaker, which allow the A8X to be used in almost any application.

Review: A8X: a "powerful link" between near- and midfield monitors!

"The A8X is a powerful link between ADAM´s AX Series and the formidable and more expensive SX Series. Its all-in-all homogenous tuning, the deep and precise bass as well as the brilliant mid- and high-frequency reproduction make this speaker a huge recommendation for ambitious people without deep pockets." (Professional Audio 10/2010)

The CMS 50 is the most compact monitoring loudspeaker of all the Focal Professional range. Its design permits listening from 50cm away, while still keeping the possibility of the monitors at a great distance from one another without damaging the soundstage. The 5” mid-woofer reaches down to 55Hz, while offering a controlled bass and a totally linear midrange. The midrange register of the CMS 50 has unequalled neutrality in its price range. The Al-Mg inverted dome tweeter offers outstanding dynamics and a degree of definition in the treble that allow precise measurement of reverb and other effects which are normally very difficult to assess.

Behringer MS-20 24-Bit/192 kHz Digital 20-Watt Stereo Near Field Monitors

The MS20 Studio Monitors from Behringer are a pair of extremely compact, 2 x 10-Watt nearfield monitors that feature high-resolution 24-bit/192 kHz D/A converters. With the MS20, you can connect directly to your digital signal sources and eliminate annoying analog line-loss and hum forever. Whether you connect to your computer sound card, keyboard, or MP3 player, you will enjoy exceptional sound quality with great dynamics. The built-in amplifiers provide lots of headroom, while the powerful woofers and tweeters provide ultra-linear frequency response.

The MS20 connectivity includes stereo 1/8" and RCA jacks, which can be used simultaneously or mixed with a digital stereo source. Digital duties are handled by either RCA or TOSLINK sockets, providing for ultra-simple hookup. Individual volume controls for both Line inputs plus Bass and Treble EQ controls are provided on the front panel, along with a 1/4" headphone jack that automatically mutes the internal speakers.

Sound Quality
Sporting 3.625" woofers and 2.5" high-resolution tweeters, MS20 monitor speakers bring quality audio within the reach of anyone that operates a computer workstation. Whether you're a musician tracking your latest masterpieces, or just someone who listens to your favorite songs at work, MS20 loudspeakers will make them sound significantly better. They also make excellent add-on speakers for electronic keyboards. Front-mounted volume and individual bass and treble controls make accurate sound adjustments a breeze.

Built-in Mixer
The MS20 takes audio to an even higher level with its multiple input options. The built-in mixer features 1/8" stereo inputs for connecting CD/MD/MP3 players, dual RCA jacks for tape decks and stereo keyboard modules, and even both RCA and TOSLINK connectors for digital signal sources. This adds up to a system that lets you play along with a variety of prerecorded tracks. And you can wail away to your heart's content in total privacy, thanks to MS20's powerful headphone jack.

 FEATURES

• 2-Way active studio monitor pair
• Ideally suited for computer studios, multimedia workstations and keyboards
• Built-in 2 x 10-Watt powerful amplifiers with lots of headroom
• Powerful woofers and high-resolution tweeters
• High-resolution 24-bit/192 kHz D/A converters for extended dynamic range
• Optical and coaxial inputs to directly connect digital audio sources by S/PDIF interface
• Two stereo analog inputs featuring 1/4'' TRS and stereo RCA connectors
• Individual volume controls for both Line inputs plus Bass and Treble EQ controls
• 1/4'' TRS headphone connector with auto-mute loudspeaker function easily accessible on the front panel

SPECIFICATIONS

MS20 Digital Monitor Speakers (Pair)

• Loudspeakers
  Tweeter: ˜ 65 mm (2 1/2“), 8 ?
  Woofer: ˜ 92 mm (3 5/8“), 4 ?
  Audio Inputs
  Line 1: 1/8" TRS stereo, impedance 20 k?
  Line 2: 2 RCA, impedance 20 k?
  Digital Inputs
  Optical: TOSLINK
  Coaxial: RCA
  Converter: 24-bit
  Sample rate: System Specs
  Output power: 2 x 20W
  Frequency response: 50Hz to 25kHz
  Power Supply
  Mains Voltages: USA/Canada 120 V, 60 Hz
  Power Consumption: 80W