| Content |
• Compact, lightweight fog machine emits thick bursts of water-based fog to enhance any light show
• Enhance operation and safety with the LED-illuminated tank
• Features a 1.3L tank capacity and quick, 1.5-minute heat up time for an output of 4,000cfm
• Water-based components will not leave any residue
• Operate the machine from a distance using the included wired remote
• Tank Capacity: 0.3 gal (1.3 l)
• Remote Length: 15 ft (4.6 m)
• Heat-up Time: 1.5 min
• Output: 4,000 cfm
• Fluid Consumption: 11 ml/min
• Input Voltage: 120 VAC, 60 Hz or 230 VAC, 50 Hz
• Power and Current: 670 W, 5.6 A @ 120 V, 60 Hz
• Power and Current: 670 W, 2.9 A @ 230 V, 50 Hz
• Bracket Mounting Hole: M8 (3)
• Weight: 7.7 lb (3.5 kg)
• Size: 10.4 x 8.7 x 9.1 in (264 x 221 x 231 mm)
• Approvals: CE
| Digital technology and a new Design
The viper 2.6 is a very powerful fog generator. It unites the current digital technology with proven technique and power.
Very powerful output, simple handling and the possibility to connect an external fan are the main new features of this machine.
Features:
- Finest adjustments of the output Digital technology enables fine adjustments of the pump. In steps of 1% the output can be adjusted from 0 - 99%. Thus, any desired effect - from a tiny fog cloud to the thickest continuous fog - can be produced. This allows an individual adaptation to the dimensions of the room. The fan can be adjusted separately from 0 - 99% .
- DMX 512 as standard
The Viper 2.6 can be controlled via DMX 512. Pump and fan can here be controlled separately. Thus, the connected fan can be used as wind machine as well. The connection is done with 5pin-XLR-plugs, two following addresses will be taken. The DMX start address can be adjusted and saved via the control panel. The address remains saved also when the machine is unplugged. The machine can also be controlled with analog (0 - 10V) via a lighting desk or a XLR-remote (option). The adjustment of the fan is done directly at the machine, the pump can be adjusted via the analog control. The connection is done with 3-pin-XLR-plug. A Stand-Alone-Mode is possible as well. The adjustments of the pump and the fan are done directly at the machine. Pressing the start button once, the machine starts running with the pre-adjusted levels.
With the internal timer, the fogging time can be adjsted in seconds, the wait time in minutes and the output in %. Once the timer is activated, the adjusted program will run until the timer is deactivated.
The control panel with LED display and simple symbols allow an easy operation. It also protects the control buttons against dirt.
- Robust flightcase version
The flightcase on wheels protect the inbuild machine and fan and ensures an easy transport and flexible handling. Handles at both sides of the case allow an easy lifting. Removable lids enable direct access to control panels and fluid tank.
Liquid
The following Look fog liquids are available for the Viper 2.6/Viper deLuxe: Quick-Fog (thick, quick disappearing fog liquid) Regular-Fog (thick, long lasting fog liquid) Slow-Fog (thick, extremely long lasting fog liquid)
Safety
The viper 2.6 is equipped with new safety features.
On the front and the back part of the cover there are fixing points for safety bonds.
At both sides of the bottom of the machine are three holes to which a hanging yoke
complete with a collecting tray for fluid drips can be fixed.
Fluid
The following Look-fluids are available for the viper 2.6:
Quick-Fog (thick, quick disappearing fluid)
Regular-Fog (thick, long lasting fluid)
Slow-Fog (thick, extremly long lasting fluid)
Technical Data
Procedure: vaporizing fog generator
Power requirement: 2600 Watt
Voltage: 230 V / 50 Hz
Warm up time: approx. 7 min.
Fluid consumption at max. output
at continuous output: 240 ml/min.
70 ml/min.
Fluid tank capacity: 5 liter
Fog output: adjustable in 99 steps
Output projection: max. 15 m
Fogging time at
external Fan: max. 800 Watt
Air quantity adjustable in 99 steps
Control: DMX 512
0 - 10 V analog
Stand-alone-Mode
Radio remote (Option)
Temperature control: Microprocessor controlled
Overheating protection: Heater block/Thermostat
Pump/Thermal switch
Dimensions (L x W x H): 520 x 230 x 250 mm
Weight without bottle: approx. 12 kg |
The cutting-edge wireless control system gives Antari W series a simple setting and operation interface. Additionally, the state-of-the-art heater design upgrades the W Series fog machines to a higher level in terms of good quality fog and energy efficiency. In conclusion, Antari W Series bring users to a professional scene in an easier method. Main Features: 1. Intelligent Wireless Control System Each machine comes with a set of wireless receiver and transmitter as standard controller. The working distance of wireless control is 50 meters in open area. 2. Opto-electronic Fluid Sensor When the fluid recipient runs dry,the fluid sensor stops pumping automatically to protect pump from burning. 3. More Efficient New Heat Exchanger Design It can generate drier fog with smaller particles.This leads to a fairly low fog fluid consumption.Compare to the equivalent power consumption heat exchangers, the same quantity of fog fluid in W series can produce 20% more fog than others. 4. New Advanced PCB (Printed Circuit Board) Design The new system can control temperature precisely and rule out the influence from outside environments as much as possible to make W series fog machines be able to work stably between - 20 and + 60 degree Celsius.
Specification
» Power : AC100V/AC120V/AC230V/AC240V,50Hz-60Hz » Heater : 800 W » Output : 3,000 cu.ft / min » First Heat-up Time : 100 seconds » Tank Capacity : 0.8 liter » Fluid Consumption Rate : 60 min / 0.8liter (100% Output) » Remote Included : W-1 Wireless Remote » Weight : 3.8 Kg » Dimensions (mm) : L 315 W 128 H 166 » Liquid Used : Antari FLR / FLG Liquid
|
Z-80 with Wireless Remote
UK Version
• Z80 MK2 included wireless remote
• UK power connector
Technical Info
Power supply: AC 230/240 V – 50/60 Hz
Heater: 700 Watt
Output: 2500 cu. ft/min
Tank capacity: 0,8 L
Fluid consumption rate: 125 min/ L
Included remote: FC-5
Optional remote: FC-4
Dimensions: 330 x 160 x 130 mm (LxWxH)
Weight: 4,0 kg
|
Martin JEM CLUB SMOKE Machine - Remote Control
|
- Fog machine for small party rooms
- On/off cable remote control
- Mounting bracket
- Overheat protection
- Fluid level indication
- Smoke-output: ca. 2 m
- Control: Wired remote control provided
- Power supply of device: Fix fehlt
Technical specifications
| Power supply: |
230 V AC, 50 Hz |
| Smoke-output: |
2 m |
| Warm-up time: |
5 min. |
| Output volume: |
14 m³/min. |
| Tank capacity: |
0.3 l |
| Dimensions (L x W x H): |
265 x 145 x 170 mm |
| Weight: |
2,5 kg |
| Power consumption: |
400 W |
| Fluid consumption: |
ca. 21 - |
| IP classification: |
IP20 |
| Color: |
Silver |
| Height: |
17 cm |
| Depth: |
26,5 cm |
| Width: |
14,5 cm |
Packaging units
| PU |
EAN |
Weight |
Dimensions |
| 1 |
4026397578775 |
2,06 kg |
29cm x 15cm x 15cm |
|
Reviews
There are no reviews yet.