The XLC2800 Power Amplifier is compact, powerful and cost-effective with ease of installation, outstanding sound quality and the unwavering reliability inherent in every Crown product. – Power for 2 ohm, 4 ohm and 8 ohm outputs, supporting stereo, parallel and bridge outputs. – Support parallel connection of cinema surround speaker. – Indicators provide accurate diagnostics: […]
The XLC2800 Power Amplifier is compact, powerful and cost-effective with ease of installation, outstanding sound quality and the unwavering reliability inherent in every Crown product.
– Power for 2 ohm, 4 ohm and 8 ohm outputs, supporting stereo, parallel and bridge outputs.
– Support parallel connection of cinema surround speaker.
– Indicators provide accurate diagnostics: Power, Signal, Clip and Fault.
– Volume control on rear panel.
– Input configuration: Stereo and parallel
– Output configuration: Stereo and bridge
– HD-15 and phoenix connectors make the system wiring easy.
– High performance, light weight class-D amplifier – weights less than 12 lbs / 5kg (net weight).
Model Number XLC2800
Product Type Power Amplifier
Compatible Speakers JBL 3722(N), 4722(N), 3730, 3252(N), 4641, 4642A, 8320, 4181, 8281, 8340A, 8350, SCS8, SCS12
Compatible Monitors Crown Monitor and Crossover System CXM2000 for monitor, fault detection and crossover functions
Crown Monitor System DSi-8M for monitor function
Stereo (all channels driven) Specifications
2-ohms 1200W
4-ohms 775W/800W*
8-ohms 440W
Bridge Specifications
4-ohms 2400W
8-ohms 1550W
Amplifier Performance Specifications
AC Line Voltage and Frequency, Configurations Available (+/-10%) 100VAC 50/60Hz, 110VAC 60Hz, 220/230~240VAC 50Hz
Voltage Gain 42
Sensitivity (for full rated power at 4 ohms) 1.4V
Signal-to-Noise Ratio (ref. rated power, 8 ohms, 1kHz) >103dB
Total Harmonic Distortion (THD) (1kHz) 200
Intermodulation Distortion (IMD) (60Hz ~ 7kHz, 4:1, from full rated output to -30dB) 85dB
Crosstalk (below rated 8 ohms power) At 20kHz >55dB
Input Impedance (nominal) 20 kilohms balanced; 10 kilohms unbalanced
Load Impedance 2~8 ohms per channel in Stereo; 4~8 ohms in Bridge
Dimensions Specifications
Width x Height x Depth 19 in. (48.3 cm) x 3.5 in. (8.9 cm) x 10.4 in. (26.4 cm)
Net Weight 10.4 lbs (4.72 kg)
Shipping Weight 13.2 lbs (6 kg)
Weight
4.72 kg
Reviews
There are no reviews yet.
Be the first to review “CROWN XLC-2800 Power Amplifier” Cancel reply
The XLC2800 Power Amplifier is compact, powerful and cost-effective with ease of installation, outstanding sound quality and the unwavering reliability inherent in every Crown product.
- Power for 2 ohm, 4 ohm and 8 ohm outputs, supporting stereo, parallel and bridge outputs.
- Support parallel connection of cinema surround speaker.
- Indicators provide accurate diagnostics: Power, Signal, Clip and Fault.
- Volume control on rear panel.
- Input configuration: Stereo and parallel
- Output configuration: Stereo and bridge
- HD-15 and phoenix connectors make the system wiring easy.
- High performance, light weight class-D amplifier - weights less than 12 lbs / 5kg (net weight).
Model Number XLC2800
Product Type Power Amplifier
Compatible Speakers JBL 3722(N), 4722(N), 3730, 3252(N), 4641, 4642A, 8320, 4181, 8281, 8340A, 8350, SCS8, SCS12
Compatible Monitors Crown Monitor and Crossover System CXM2000 for monitor, fault detection and crossover functions
Crown Monitor System DSi-8M for monitor function
Stereo (all channels driven) Specifications
2-ohms 1200W
4-ohms 775W/800W*
8-ohms 440W
Bridge Specifications
4-ohms 2400W
8-ohms 1550W
Amplifier Performance Specifications
AC Line Voltage and Frequency, Configurations Available (+/-10%) 100VAC 50/60Hz, 110VAC 60Hz, 220/230~240VAC 50Hz
Voltage Gain 42
Sensitivity (for full rated power at 4 ohms) 1.4V
Signal-to-Noise Ratio (ref. rated power, 8 ohms, 1kHz) >103dB
Total Harmonic Distortion (THD) (1kHz) 200
Intermodulation Distortion (IMD) (60Hz ~ 7kHz, 4:1, from full rated output to -30dB) 85dB
Crosstalk (below rated 8 ohms power) At 20kHz >55dB
Input Impedance (nominal) 20 kilohms balanced; 10 kilohms unbalanced
Load Impedance 2~8 ohms per channel in Stereo; 4~8 ohms in Bridge
Dimensions Specifications
Width x Height x Depth 19 in. (48.3 cm) x 3.5 in. (8.9 cm) x 10.4 in. (26.4 cm)
Net Weight 10.4 lbs (4.72 kg)
Shipping Weight 13.2 lbs (6 kg)
InterM V-2000 Power amplifier 2Χ550W/4ohm, 2Χ300W/8ohm, 2Χ900W/2ohm bridge 1900W/4ohm
Crownʼs new CTs series of power amplifiers are remarkable for their loud, punchy sound; sustained, tight bass; and superior protection against overheating and overload. This paper explains the design features behind those advantages. After reading this information, youʼll know why Crown CTs amps sound better than the competition. CTs amplifiers can provide large amounts of power into various loads, such as 2, 4, 8 ohms and 70V. With most power amps, the maximum output power tends to drop as the load impedance increases. But with the CTs series, the power stays the same at almost any impedance. 2-ohm Dual (per Ch.) 250W 4-ohm Dual (per Ch.) 600W 8-ohm Dual (per Ch.) 600W 16-ohm Dual (per Ch.) 300W 70V Dual (per Ch.) 600W 4-ohm Bridge 500W 8-ohm Bridge 1200W 16-ohm Bridge 1200W 140V Bridge 1200W Crown switching power supply for less weight Sustained Power on long-duration signals due to regulated, "stiff” power supplies with incredible energy storage (huge filter capacitors). Extra Hidden Power during high-level transients and during incomplete use of all the channels. Overheating and overload protection thanks to the sophisticated TLC circuitry which compresses the signal only when needed. Compression is controlled not by temperature, but by signal voltage. This keeps the loudness up during compression more than with competitive amps.
The high efficiency of the ED series enables maximum efficiency with low heat generation.
A new and unique Class-H circuity technology using state of the art SMD Surface Mount Technology with a reduced number of components offering performance levels exceeding audiophile levels like a slew rate of 50V/µs and high-end extended dynamic sound. The 2U amplifier provides 2x550W into 4 Ohm is equipped complete with temperature-controlled fan cooling, all common protective circuits such as over-temperature, short circuit, RFI and soft start.
The integral soft clip limiter protects against damage to the connected loudspeakers, the activity of a protective circuit, signal and limiter are shown for each channel by LEDʼs.
AMPLIFIER SPECIFICATIONS
Power output stereo 4Ω:
2 x 550 Watt rms
Power output stereo 8Ω:
2 x 265 Watt rms
Power output bridged 8Ω:
1100 Watt rms
Frequency Response:
20 Hz ÷ 20 kHz
Signal/noise rate:
> 105 dB
Crosstalk:
> 70 dB
Distortion (THD+N):
Intermodulation:
Damping factor:
200:1 (8 Ω)
Slew rate:
50 V/μS
INPUT SECTION
Input connector:
2 x XLR balanced, 6,3mm jack unbalanced
Input sensitivity:
0 / 0.775 dBm/V RMS
Input impedance:
10 kΩ
Controls:
Volume control for each channel
OUTPUT SECTION
Output connector:
2 x Neutrik Speakon 4 ways
SYSTEM PARAMETERS
Cooling:
Two-speed fan
Protections:
Thermal, direct current, RFI, short circuit, transformer protection
Damping Factor Not Specified By Manufacturer
Input Sensitivity 26dB Setting - 3.28V
32dB Setting - 1.60V
Input Impedance > 10kΩ balanced, or unbalanced
Gain 34.5dB
Frequency Response 20Hz to 20kHz, +/- 0.2dB
Signal-to-Noise Ratio -106dB
Total Harmonic Distortion (THD) 0.02% @ 2Ω
0.005-0.01% @ 4Ω
0.002-0.01% @ 8Ω
Input Connections Input: XLR Male, XLR Female and 3-pin detachable terminal blocks (1 each per channel)
DataPort: HD-15, input signal in parallel with XLR input connectors
Output Connectors Output: Neutrik Speakon (ch 1 wired to both channels) and 5-way binding posts
Controls Front Panel AC Power Switch
Gain Controls, 21 detents, 1 dB steps (each channel)
Controls (Rear) Input Mode: Bridge (Yellow), Stereo (Green), or Parallel (Orange)
Gain / Sensitivity: 26dB (Orange), 32dB (Green), or 1.2V (Yellow)
High Pass (each channel): 3Hz (Off), 30Hz (Yellow), or 50Hz (Orange)
Clip Limiter (each channel): Off, On (Yellow)
Indicators Clip Limiter (each channel): Off, On (Yellow)
Camera Resolution Flow-thru air path and solid aluminum heat sinks
Power Consumption 120V 50/60Hz - 8.5A
230V 50Hz - 7.5A
Power Requirements Not Specified By Manufacturer
Dimensions (WxHxD) 19 x 3.5 x 15.63" (48.3 x 8.9 x 39.7cm)
Weight 33.5 lbs (15.2kg)
Specialties Parallel Dataport, XLR/M and XLR/F connectors for simple loop-through connectivity
- Power levels matched to the most popular speakers used by entertainers - Optimized for maximum real-world headroom into 4 ohm and 8 ohm speaker systems - Inputs: XLR, 1/4" TRS and phono input connectors for compatibility with any source - Outputs: Speakon(R) combo accepts, 1/4" (TS) plugs or Speakon 2-pole and 4-pole plugs (connects 2 poles only). Binding posts support all other speaker wiring systems - Minimum depth chassis (10.1“/257 mm) fits in compact, inexpensive effects racks - Lightweight - GX7 is only 15.5 lbs (7 kg) - Detented gain controls for precise setting and matching of sensitivity - GuardRail(TM) automatically protects the amplifier and loudspeakers from damage due to temperature rise or overdrive without shutting down the show - Front panel LEDs monitor Power, Signal and Clipping - Subwoofer/Satellite crossover built-in - 230V 16.5 lbs (7.5 kg)
This website uses cookies to improve your experience. We'll assume you're ok with this, but you can opt-out if you wish. Cookie settingsACCEPT
Privacy & Cookies Policy
Πολιτική χρήσης
Αυτός ο ιστότοπος χρησιμοποιεί cookies για να βελτιώσει την εμπειρία σας ενώ περιηγείστε στον ιστότοπο. Από αυτά τα cookies, κάποια cookie κατηγοριοποιούνται ως απαραίτητα να αποθηκεύονται στο πρόγραμμα περιήγησης σας, καθώς είναι απαραίτητα για τη λειτουργία βασικών λειτουργιών του ιστότοπου. Χρησιμοποιούμε επίσης cookies τρίτων που μας βοηθούν να αναλύσουμε και να κατανοήσουμε πώς χρησιμοποιείτε αυτόν τον ιστότοπο. Αυτά τα cookies θα αποθηκευτούν στο πρόγραμμα περιήγησης σας μόνο με τη συγκατάθεσή σας. Έχετε επίσης την επιλογή να εξαιρεθείτε από αυτά τα cookies. Ωστόσο, η εξαίρεση από ορισμένα από αυτά τα cookie μπορεί να επηρεάσει την εμπειρία περιήγησης σας.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.
Reviews
There are no reviews yet.