Content | Crown XTi 4002 Features at a Glance:
* Stereo Wattage: 1600W @ 2 ohms, 1200W @ 4 ohms, 650W @ 8 ohms
* Bridged Mono Wattage: 2400W @ 8 ohms, 3200W @ 4 ohms
* Peak Plus Limiters provide the ultimate in system performance and protection by allowing full control over threshold, attack, and release
* Enhanced Subharmonic Synth section provides user control over frequency, gain and filter type for system-specific tuning
* 3 User-defined fan mode controls - normal, early and fullspeed - for matching fan performance to a specific application
* New system monitoring provides software visibility of AC line voltage and power supply temperature
* Integrated cast-aluminum handles for easy handling and enhanced durability
* Locking power cord clip provides a secure connection between the amplifier and power cord
* Updated HiQnet Band Manager and System Architect control software
* Increased number of presets to a total of 30; 29 of which are user definable |
Power Rating
Stereo Mode:
8Ω EIA 1 kHz 1% THD - 800W
4Ω EIA 1 kHz 1% THD - 1250W
2Ω EIA 1 kHz 1% THD - 2000W
Bridged Mono:
8Ω EIA 1 kHz 1% THD - 2600W
4Ω EIA 1 kHz 1% THD - 4000W
Damping Factor Not Specified By Manufacturer
Input Sensitivity 26dB Setting - 3.92V
32dB Setting - 1.96V
Input Impedance > 10kΩ balanced, or unbalanced
Gain 36.4dB
Frequency Response 20Hz to 20kHz, +/- 0.2dB
Signal-to-Noise Ratio -105dB
Total Harmonic Distortion (THD) 0.02% @ 2Ω
0.005-0.01% @ 4Ω
0.002-0.01% @ 8Ω
Input Connections Input: XLR Male, XLR Female and 3-pin detachable terminal blocks (1 each per channel)
DataPort: HD-15, input signal in parallel with XLR input connectors
Output Connectors Output: Neutrik Speakon (ch 1 wired to both channels) and 5-way binding posts
Controls Front Panel AC Power Switch
Gain Controls, 21 detents, 1 dB steps (each channel)
Controls (Rear) Input Mode: Bridge (Yellow), Stereo (Green), or Parallel (Orange)
Gain / Sensitivity: 26dB (Orange), 32dB (Green), or 1.2V (Yellow)
High Pass (each channel): 3Hz (Off), 30Hz (Yellow), or 50Hz (Orange)
Clip Limiter (each channel): Off, On (Yellow)
Indicators Clip Limiter (each channel): Off, On (Yellow)
Camera Resolution Flow-thru air path and solid aluminum heat sinks
Power Consumption 120V 50/60Hz - 12A
230V 50Hz - 7A
Power Requirements Not Specified By Manufacturer
Dimensions (WxHxD) 19 x 3.5 x 15.63" (48.3 x 8.9 x 39.7cm)
Weight 33.5 lbs (15.2kg)
Specialties Parallel Dataport, XLR/M and XLR/F connectors for simple loop-through connectivity
| VLP Series Power Amplifier
- 1100W RMS Per Channel @ 4 Ohms, 1kHz, 0.1% THD
- 700W RMS Per Channel @ 8 Ohms, 1kHz, 0.1% THD
- 2200W RMS @ 8 Ohms, 1K Hz, 1% THD (Bridge Mode, Mono)
- Total Harmonic Distortion: Less Than 0.5% (20Hz - 20kHz @ 8 Ohms)
- Frequency Response: (+/-05db, @rated output Power, 8 Ohms): 20Hz - 20K Hz
- Slew Rate: 20V Per usec
- Damping Factor @ 8 Ohm: 450
- Impedance: 20 Ohms balanced / 10 Ohms unbalanced
- Cooling System: 2 high speed cooling fans
- Special Features: High/Low Pass Filter / Input Sensitivity Selector / Ground Lift / Limiter
- Dimensions (LxWxH): 17.75" x 19" x 3.5" / 453 x 482 x 88mm (2 rm spaces)
- Weight: 50 lbs. / 23 Kgs. |
A full model revision takes Yamaha's high-end PC-N power amplifiers to the next level - the PC-1N
Series. The new PC-1N Series amplifiers feature an extraordinarily solid low end, rich midrange,
and superbly defined highs. They also deliver fast response and exceptional stability even in the
face of serious power supply limitations. Refinements throughout this expanded five-model lineup
make these amplifiers the new benchmarks for quality, reliability, and versatility in professional
applications. Frequency Response: 10 Hz – 40 KHz. Output Power: 2 x 750 Watt / 8Ω RMS,
2 x 1150 Watt / 4Ω RMS, 2300 Watt / 8Ω bridge RMS. Weight: 12,5 Kg. |
RMXa Series: Professional quality performance, incorporating road-proven QSC designs
- Compact size — up to 2500 watts in two rack spaces, or 5000 watts in three rack spaces
- High-current toroidal transformers, for greater 2-ohm power and low noise
- Independent user-defeatable clip limiters reduce distortion
- Selectable low-frequency filters (30 Hz or 50 Hz) protect speakers and increase headroom
- The 4000-watt RMX4050a operates on a standard 15 amp plug (120V)
- Both the RMX4050a and the RMX5050a feature a dual mono, high-current power supply for increased reliability and performance
- The RMX4050a's particularly exceptional combination of cooling capacity and electrical efficiency provides robust thermal performance suitable for high continuous power in 2-ohm stereo or 4-ohm bridged applications.
- Balanced 1/4” (6.3 mm) TRS, XLR, and barrier strip inputs
- Touch-proof binding post and Neutrik Speakon® outputs
- Front mounted gain controls for easy access
- Signal and clip LED indicators for monitoring performance
- Independent DC and thermal overload protection on each channel automatically protects amplifier and speakers
- 3-year warranty plus optional 3-year extended service contract
|
Amplifier Gain 41.5 dB, 35 dB, 32 dB (switchable)
CAN Bus Interface Optional with RCM-26
Continuous Rated Power
(1 kHz, THD 1%) 2Ω 2000 Watts
Continuous Rated Power
(1 kHz, THD 1%) 4Ω 1450 Watts
Continuous Rated Power
(1 kHz, THD 1%) 8Ω 850 Watts
Continuous Rated Power
(20-20 kHz, THD |
Reviews
There are no reviews yet.