| Content | Specifications: • Power output: 3,000 watts 2 ohm stereo per ch, 2,100 watts 4 ohm stereo per ch, 1,200 watts 8 ohm stereo per ch, 4,200 watts 8 ohm bridge-mono, 6,000 watts 4 ohms bridge-mono • Sensitivity (for full rated power at 4 ohms): 1.4V RMS • Frequency response (at 1 watt, 20 Hz - 20 kHz): +0 dB, –1 dB • S/N Ratio (below rated 1 kHz power at 8 ohms): 103 dB (A weighted) • T.H.D.: 500 • Crosstalk (below rated power): 20 kHz - 1 kHz: >70 dB • Input impedance (nominal): 20k ohms balanced, 10k ohms unbalanced • Maximum input signal: +22 dBu typical • AC Line voltage and frequency configurations: 120 VAC 60 Hz • AC Line current (120 VAC amplifier playing 1/8 power pink noise into 4 ohms per ch): 15.3A; no more than 180 watts at idle • Operating temperature: 0°C to 40°C at 95% relative humidity (non-condensing) • Dimensions: 19" W x 3.5" H x 16.2" D • Net weight: 24 lbs. (13.6 kg). |
Number of Channels: 2
Output Power: (per channel)
8 ohms 1000W
4 ohms 1850W
2 ohms N/A
Output Power: (bridged)
8 ohms 3700W
4 ohms N/A
THD%: (@1dB below max output)
@ 1kHz |
Power Rating
Stereo Mode:
8Ω EIA 1 kHz 1% THD - 1500W
4Ω EIA 1 kHz 1% THD - 2500W
2Ω EIA 1 kHz 1% THD - 4000W
Bridged Mono:
8Ω EIA 1 kHz 1% THD - 5000W
4Ω EIA 1 kHz 1% THD - 8000W
Damping Factor Not Specified By Manufacturer
Input Sensitivity 26dB Setting - 5.27V
32dB Setting - 2.67V
Input Impedance > 10kΩ balanced, or unbalanced
Gain 39.1dB
Frequency Response 20Hz to 20kHz, +/- 0.2dB
Signal-to-Noise Ratio -104dB
Total Harmonic Distortion (THD) 0.1% @ 2Ω
0.03-0.06% @ 4Ω
0.01-0.03% @ 8Ω
Input Connections Input: XLR Male, XLR Female and 3-pin detachable terminal blocks (1 each per channel)
DataPort: HD-15, input signal in parallel with XLR input connectors
Output Connectors Output: Neutrik Speakon (ch 1 wired to both channels) and 5-way binding posts
Controls Front Panel AC Power Switch
Gain Controls, 21 detents, 1 dB steps (each channel)
Controls (Rear) Input Mode: Bridge (Yellow), Stereo (Green), or Parallel (Orange)
Gain / Sensitivity: 26dB (Orange), 32dB (Green), or 1.2V (Yellow)
High Pass (each channel): 3Hz (Off), 30Hz (Yellow), or 50Hz (Orange)
Clip Limiter (each channel): Off, On (Yellow)
Indicators Clip Limiter (each channel): Off, On (Yellow)
Camera Resolution Flow-thru air path and solid aluminum heat sinks
Power Consumption 120V 50/60Hz - 18A
230V 50Hz - 11A
Power Requirements Not Specified By Manufacturer
Dimensions (WxHxD) 19 x 3.5 x 15.63" (48.3 x 8.9 x 39.7cm)
Weight 33.5 lbs (15.2kg)
Specialties Parallel Dataport, XLR/M and XLR/F connectors for simple loop-through connectivity
|
RMXa Series: Professional quality performance, incorporating road-proven QSC designs
- Compact size — up to 2500 watts in two rack spaces, or 5000 watts in three rack spaces
- High-current toroidal transformers, for greater 2-ohm power and low noise
- Independent user-defeatable clip limiters reduce distortion
- Selectable low-frequency filters (30 Hz or 50 Hz) protect speakers and increase headroom
- The 4000-watt RMX4050a operates on a standard 15 amp plug (120V)
- Both the RMX4050a and the RMX5050a feature a dual mono, high-current power supply for increased reliability and performance
- The RMX4050a's particularly exceptional combination of cooling capacity and electrical efficiency provides robust thermal performance suitable for high continuous power in 2-ohm stereo or 4-ohm bridged applications.
- Balanced 1/4” (6.3 mm) TRS, XLR, and barrier strip inputs
- Touch-proof binding post and Neutrik Speakon® outputs
- Front mounted gain controls for easy access
- Signal and clip LED indicators for monitoring performance
- Independent DC and thermal overload protection on each channel automatically protects amplifier and speakers
- 3-year warranty plus optional 3-year extended service contract
|
Amplifier Gain 39 dB, 35 dB 32 dB (switchable)
CAN Bus Interface Optional with RCM-26
Continuous Rated Power
(1 kHz, THD 1%) 2Ω 3500 Watts
Continuous Rated Power
(1 kHz, THD 1%) 4Ω 2500 Watts
Continuous Rated Power
(1 kHz, THD 1%) 8Ω 1500 Watts
Continuous Rated Power
(20-20 kHz, THD |
The E Series is a range of lightweight, high-power switch mode amplifiers designed to the highest standards of reliability and sound quality. Developed for the touring market, E Series retain the sonic integrity of the benchmark MC and T Series amplifiers, without the physical weight.
The switch mode power supply is capable of delivering high peaks without any perceptible bass 'sag' at very low distortion and is kept within its safe operating area by the new, sophisticated MC² Audio 'intelligent' limiter. The E15, E25, E45 and E4-75 feature MC² Audioʼs proprietary current driven output stages for ultra-high definition sound, delivered over the entire audio bandwidth.
The E90 and the E100 are Class D amplifiers designed to meet the demands for higher power with increased efficiency whilst still maintaining the renowned MC² Audio sonic qualities and unsurpassed reliability.
All MC² Audio products are covered by a 5 year warranty.
Number of Channels: 2
Frequency Response:
20Hz to 20kHz
(+/- 0.3dB)
Output Power: (per channel)
8 ohms 1250W
4 ohms 2500W
2 ohms 4200W
Output Power: (bridged)
8 ohms 5000W
4 ohms 8400W
THD%: (@1dB below max output)
@ 1kHz 20Hz to 20kHz
Gain / Sensitivity:
Gain 26/32/33dB
Sensitivity (for max power) dBu +15.7/9.7/5.7 (4.7/2.4/1.5V)
Power Consumption:
Nominal @ 240v into 4 ohms 4.5A
Nominal @ 120v into 4 ohms 9.0A
Dimensions: (2U) (mm)
Amplifier 88(h) x 482(w) x 428(d)
Single Box (UK shipping) 230 x 580 x 560
Double Box (outside UK) 250 x 610 x 600
Weight:
Amplifier 11.4kg
Boxed (shipping weight) 13.4kg User's Manual
|
Reviews
There are no reviews yet.