Content |
The DNRP-WRC provides two button record control and visual status indication of a connected Denon® DN-F450R/F650R recorder.
The mouse sized unit, once connecte to the recorder using its integral 5 metre lead, can be placed in a convenient location on a board/ meeting room table to allow the recording of conferences and discussions. Visual indication of recorder status is provided by high brightness red and green indicators located around the RECORD button, which show STOP, PLAY, PLAY PAUSE, PLAY F.FWD, PLAY F.REV, CARD ERROR, RECORD and RECORD PAUSE. The two button control allows the recorder to be placed into record mode, create a new record mark and stop the recording process.
The DNRP-WRC is primarily for the simple control of audio recording in areas where conversations, discussions or conferences are taking place. The unit allows the DNF450R/F650R recorder to be placed out of sight to prevent media tampering or access to all the recorder controls.
- Simple unobtrusive controller for the recording of audio in board/meeting rooms
- Easy connection to Denon DN-F450R/F650R recorder serial (RS232) port
- Provides bright visual indication of STOP, PLAY, PLAY PAUSE, PLAY F.FWD, PLAY F.REV, CARD ERROR, RECORD and RECORD PAUSE
- RECORD and STOP buttons allow simple control without the need to access the recorder
- Ergonomic visually pleasing design with internal weight to prevent table slip
- Ultra low power consumption, no need for additional power adaptor
- Fully sealed label provides protection against drink spills
|
The DP-24SD Digital Portastudio is a 24-track workstation, allowing eight tracks of simltaneous recording. The built-in mixer includes everything you need for a professional-sounding mix, from EQ and reverb to amp simulation and multi-band mastering effects. The Digital Portastudio series creates finished productions without the need for a computer, instead using a simple-to-use control surface to keep you creative.
For clear display of your mix, the DP-24SD has a large color LCD displaying tracks, meters, and effects parameters. A set of 12 encoders control EQ, effects sends, and panning. Built-in effects include compression, guitar amp modeling, delay, reverb, with a total of 10 effects processirs available during mixing.
Eight XLR mic/line inputs each provide phantom power for condenser microphones, switchable in banks of four. One input includes an instrument-level impedence switch for direct input recording of guitar or bass. Balanced monitor outputs and effects sends are also provided on the rear panel. A USB output allows tracks and mixes recorded to your SD card to be transferred to a computer for CD burning or sharing online.
For a complete music production on a desktop, there's no simpler choice than the DP-24SD.
DP-24SD SPECIFICATIONS Recording Media | SD (512MB – 2GB) / SDHC card (4GB – 32GB) | File System | SD card:FAT16 / SDHC card:FAT32 | INPUT A-H
| | XLR
| | Connector | XLR-3-31(1:GND, 2:HOT, 3:COLD), Balanced | Input impedance | 2.4k ohms | Nominal input level | -14dBu | Maximum input level | +2dBu | TRS
| | Connector | 6.3mm(1/4“)TRS phone jack, Balanced | Input impedance | 22k ohms or more
/ 1M ohms(when INPUT H, GUITAR selected) | Nominal input level | +4dBu | Maximum input level | +20dBu | STEREO OUT
| | Connector | RCA pin-jack, Unbalanced | Output impedance | 200 ohms | Nominal output level | -10dBV | Maximum output level | +6dBV | EFFECT SENDS | | Connector | 6.3mm(1/4“)TS phone jack, Unbalanced | Output impedance | 200 ohms | Nominal output level | -10dBV | Maximum output level | +6dBV | MONITOR OUT | | Connector | 6.3mm(1/4“)TRS phone jack, Balanced | Output impedance | 200 ohms | Nominal output level | -2dBu | Maximum output level | +14dBu | PHONES
| | Connector | 6.3mm(1/4“)stereo phone jack | Maximum output level | 70mW + 70mW (THD+N 0.1% or less, 32 ohms loaded) | USB | | Connector
| USB Mini-B type 4-pin | Format | USB2.0 High-Speed mass-storage class | REMOTE
| | Connector
| 2.5mm TRS jack | Power | Dedicated AC adapter (TASCAM GPE248-120200-Z, included) | Power consumption | 12W (when phantom power supplying) | Dimensions | 514(W)×100.4(H)×336.9(D)mm / 20.2“(W)×4.1“(H)×13.4""(D) | Weight | 6.2kg / 13.67 lb | Accessories | AC adapter, 4GB SD card, warranty card, owner's manual |
Audio performance | Frequency response | 20Hz to 20kHz (+/-1dB, INPUT to STEREO OUT/EFFECT SENDS/MONITOR OUT) | S/N Ratio | 90dB or greater (INPUT to STEREO OUT/EFFECT SENDS/MONITOR OUT) | THD | 0.01% or less (INPUT to STEREO OUT/EFFECT SENDS/MONITOR OUT) |
Operating system requirements | Windows | | OS | Windows XP, Windows Vista, Windows 7, Windows 8 | CPU | Pentium 300MHz or more | Memory | 128MB or more | USB | USB2.0 | Macintosh | | OS | Mac OS X Snow Leopard(V10.6), OS X Lion(V10.7), OS X Mountain Lion(V10.8), OS X Mavericks(V10.9) | CPU | Power PC, iMAC, G3, G4 266MHz or more | Memory | 64MB or more | USB | USB2.0 |
|
The D-2012C is a 6U rack mountable Remote Console Unit designed for exclusive use with the D-2008SP Digital Mixing Processor Unit. Assigned to any desired channels inside the D-2008SP by the dedicated software, the D-2012C's 12 motorized faders and 8 rotary encoders can remotely adjust their volumes. Desired preset memories can be recalled using 8 function keys. It is equipped with 1 channel line input (stereo), which allows the audio signal to be transmitted to the D-2008SP via monitor bus. Audio signals inside the D-2008SP can be monitored via monitor bus through headphones connected to a stereo headphone output. The D-2012C can be installed on a desk with the additional use of an optional D-2012AS Console Case.
* 0 dB = 0.775 V Power Source | 220 - 240 V AC | Power Consumption | 18 W | Volume Adjustment | 100 mm motorized fader x 12
Rotary encoder x 8 | Line Input | 1 channel (stereo) | Headphone Output | Stereo 100 mW + 100 mW (32 Ω load) | Monitor Bus | 1 stereo input
Connector: RJ45 connector
Connection cable: Shielded twisted pair (STP) Cat 5 or higher LAN cable (2 pairs of data lines)
Maximum cable distance: 100 m (109.36 yd) (between D-2012C and D-2008SP) | LAN | Network I/F: 10BASE-T/100BASE-TX (Automatic-Negotiation)
RJ45 connector
Network protocol: TCP/IP
Connection cable: Shielded twisted pair (STP) Cat 5 or higher LAN cable
Maximum cable distance: 100 m (109.36 yd) (between D-2008SP and switching hub) | Control | RS-232C: D-sub connector (9 pins) for maintenance use | Finish | Panel: Surface-treated steel plate
Rack mounting bracket: Surface-treated steel plate | Dimensions | 482 (W) × 266 (H) × 138 (D) mm (18.98 × 10.47" × 5.43) | Weight | 6.6 kg (14.55 lb) | Accessory | Power cord (2 m (6.5 ft)) ……1
Fader knob (yellow) ……3 | Option | Console case: D-2012AS |
|
Specifications General | Recording media | | CompactFlash (CF) card | File system | | FAT32 | Recording format | | BWF (Monophonic, Polyphonic) | Number of channels | | 8 channels (44.1/48/88.2/96 kHz) 8 channels + stereo mix (44.1/48 kHz) 4 channels (176.4/192 kHz) | Quantization bit rate | | 16/24 bit | Sampling frequency | | 44.1/47.952/48/48.048/88.2/96/176.4/192 kHz (47.952/48.048: 48 kHz ± 0.1% pull-down/pull-up) | Reference clock | | Internal, Word In, Video In, Digital In (AES 1-8 IN, AES A-BIN, ADAT 1-8 IN) | Type of timecode frame | | 23.976, 24, 25, 29.97DF, 29.97NDF, 30DF, 30NDF | Limiter | | Attack time: 3 ms Release time: 300 ms Threshold: –5 dBFS Ratio: 32:1 | Analogue audio inputs and outputs | The error for nominal and maximum levels is ±1dB for all input and output jacks except the PHONES jack. | ANALOG INPUT (1-8) | | D-sub 25-pin | Input impedance | | 10 kOhm | Nominal input level | | When reference level is –9 dB: +6 dBu (1.55 Vrms) When reference level is not –9 dB: +4 dBu (1.23 Vrms) | Maximum input level (selectable) | | +15 dBu (4.36 Vrms), +18 dBu (6.16 Vrms), +20 dBu (7.75 Vrms), + 22 dBu (9.76 Vrms), +24 dBu (12.28 Vrms) | ANALOG INPUT (L/A, R/B) | | XLR-3-31 (1: GND, 2: HOT, 3: COLD) | Input impedance | | 10 kOhm | Nominal input level | | When reference level is –9 dB: +6 dBu (1.55 Vrms) When reference level is not –9 dB: +4 dBu (1.23 Vrms) | Maximum input level (selectable) | | +15 dBu (4.36 Vrms), +18 dBu (6.16 Vrms), +20 dBu (7.75 Vrms), + 22 dBu (9.76 Vrms), +24 dBu (12.28 Vrms) | ANALOG OUTPUT (1-8) | | D-sub, 25-pin | Output impedance | | 100 Ohm | Nominal output level | | When reference level is –9 dB: +6 dBu (1.55 Vrms) When reference level is not –9 dB: +4 dBu (1.23 Vrms) | Maximum output level (selectable) | | +15 dBu (4.36 Vrms), +18 dBu (6.16 Vrms), +20 dBu (7.75 Vrms), + 22 dBu (9.76 Vrms), +24 dBu (12.28 Vrms) | ANALOG OUTPUT (A/B) | | XLR-3-32 (1: GND, 2: HOT, 3: COLD) | Output impedance | | 100 Ohm | Nominal output level | | When reference level is –9 dB: +6 dBu (1.55 Vrms) When reference level is not –9 dB: +4 dBu (1.23 Vrms) | Maximum output level (selectable) | | +15 dBu (4.36 Vrms), +18 dBu (6.16 Vrms), +20 dBu (7.75 Vrms), + 22 dBu (9.76 Vrms), +24 dBu (12.28 Vrms) | PHONES connector | | 6.3-mm standard stereo jack | Maximum output power | | 45 mW + 45 mW or more (THD+N 0.1 % or less, into 32 Ohm) | Digital audio inputs and outputs | DIGITAL IN/OUT (AES/EBU) | | D-sub, 25-pin | Minimum input voltage | | 2 Vpp | Maximum input voltage | | 7 Vpp | Output voltage | | 2–5 Vpp | Format | | AES3-2003/IEC 60958-4 (AES/EBU) | DIGITAL I/O (ADAT) | | ADAT optical | Format | | ADAT | DIGITAL INPUT A-B | | XLR-3-31 | Input voltage | | 2–7 Vpp at 110 Ohm | Format | | AES3-2003 (AES/EBU) | DIGITAL OUTPUT L-R | | XLR-3-32 | Output voltage | | 2–5 Vpp at 110 Ohm | Format | | AES3-2003 (AES/EBU) | Other inputs and outputs | RS-422 | | D-sub, 9-pin | RS-232C | | D-sub, 9-pin | PARALLEL | | D-sub, 25-pin | CASCADE IN | | BNC | Input voltage | | TTL equivalent (5 V) | Input impedance | | 75 Ohm ±10 % Allowable frequency deviation of external synchronization: ± 100 ppm | CASCADE OUT | | BNC | Output voltage | | TTL equivalent (5 V) | Output impedance | | 75 Ohm ±10 % | Sampling frequency | | 44.1/47.952/48/48.048/88.2/96/176.4/192 kHz (47.952/48.048: 48 kHz ± 0.1% pull-down/pull-up) | TIME CODE IN | | BNC | Input voltage | | 0.5–5 Vpp | Input impedance | | 20 kOhm | TIME CODE OUT | | BNC | Output voltage | | 2–5 Vpp | Output impedance | | 600 Ohm ±10 | WORD/VIDEO IN | | BNC | Input voltage | | TTL equivalent (5 V) | Input impedance | | 75 Ohm ±10 % Allowable frequency deviation of external synchronization: ± 100 ppm | WORD/VIDEO THRU/OUT | | BNC OUT/THRU switch included (OUT is for WORD OUT only) | Output voltage | | TTL equivalent (5 V) | Output impedance | | 75 Ohm ±10 % | Sampling frequency (when using WORD) | | 44.1/47.952/48/48.048/88.2/96/176.4/192 kHz (47.952/48.048: 48 kHz ± 0.1% pull-down/pull-up) | ETHERNET | | RJ45 | Keyboard | | Mini-DIN (PS/2) | USB | | USB A-type, 4-pin | Protocol | | USB2.0 HIGH SPEED (480 Mbit/s) | Audio performance (analogue input to analogue outp | Frequency response | | | 20 Hz - 20 kHz | | ±0,5 dB (all sampling rates) | at 40 kHz | | +0,5 dB/–2 dB (Fs = 88.2/96 kHz) | at 80 kHz | | +0,5 dB/–5 dB (Fs = 176.4/192 kHz) | Distortion | | ≤0.005% (Reference level: –20 dB, input level: +23 dBu, 1 kHz, AES-17LPF) | S/N ratio | | ≥100 dB(A) (22 kHz LPF) | Power requirements and other specifications | Power requirements | | 100–240 V AC, 50–60 Hz | Power consumption | | 26 W | Dimensions (W x H x D) | | 483 mm x 88 mm x 288 mm | Weight | | 4.8 kg | Operating temperature range | | 5–35 °C |
|
For users of just about any TASCAM multitrack, the RC-30P is a wonderful timesaver. Punching in on recordings by hand means you're not ready to play right away. The RC-30P lets you play straight through. While automated punch-ins available on some recorders are also helpful, most punches can be done with the simple and efficient precision of the RC-30P, saving you time.
|
Stereo Rack Memory Recorder
The UR-2 is a 1 U rack size stereo audio recorder using SD card and USB storage device that is flexibly adapting to the wide variety of playback requirements.
The UR-2 is a new generation stereo memory recorder from Fostex that uses 2 SD cards (SDHC compatible) and USB storage device as the recording media. The recording/ playback file format is BWF (WAV). Its ample playback functions will adapt to the wide variety of playback requirements. It offers high quality recording of up to 24bit/96kHz (in BWF format). Employing FAT 32 disc format, it is easy to process the file transfer to a PC based DAW.
The analog input and output are balanced XLR/+4dBu and un-balanced RCA/-10dBV, the digital input and output complies to AES/EBU and S/P DIF digital signal. It is flexible to be used in the available audio system. The playback function includes Chain Play and Timer Play, it is suitable for live stage performance and sound installation. In addition to the external control via parallel remote with D-Sub 25pin and RS-232C serial remote, a USB keyboard and 10-key keyboard can trigger the instant playback start, which is very useful at a live event, theater and broadcast environments.
The Mic input located on the front panel offers 48V phantom power, it can be used not only for recording but also for speech to be mixed with playback source. Last but not least, its newly employed organic EL display gives an extremely clear visibility. This combined with DC power operation, it serves for outdoor use very well.
MAIN FEATURES
• 2 sets SD card slots and a USB host connector for alternate recording/playback among the different media.
• Stereo or Mono WAV (BWF) recording to SD card (also SDHC) and USB storage device
• Fs: 44.1/48/88.2/96kHz, Quantization: 16/24bit
• High speed file transfer with PC via USB 2.0 (bi-directional)
• Employing FAT32 format, it allows to directly mount the recorded files to PC.
• It adapts to a wide variety of use environment by offering Chain Play and Memory Play.
• Timer Play and Power ON Play enable automatic playback start for such as chime and repetitive announcement, which are convenient in the installation audio industry.
• The play mode list employs CSV file format so that it is easy to edit by a text editor or spread sheet program software on PC.
• 99 Cue points with locate function. Waveform display under Scrub mode offers easy and visual Cue point setting
• Microphone input with P48V available on the front panel. Not only for recording but for speech to be mixed with playback source.
• Analog I/O with balanced XLR and un-balanced RCA pin jacks, Digital I/O with XLR connectors
• An organic EL display offers high visibility.
• Remote transport control via Foot SW, Parallel remote pot (Dsub 25pin) and RS-232C (D-sub 9pin)
• External USB keyboard can be used not only for file name editing but for transport control such as REC and PLAY.
|
Reviews
There are no reviews yet.