| Content | The introduction of the Drawmer DL241 Dual Channel \'Auto-Compressor\' highlights the beginning of a new generation of dynamic processors which set new standards of sonic excellence. Its combination of features, displays and well designed control functions make it an outstanding product for a vast range of broadcast, sound reinforcement, and recording applications. The DL241 \'Auto-Compressor\' incorporates many automatic functions allowing the engineer to achieve optimum results in the minimum set up time but does not compromise skilled users with limited controls. Its sophisticated design produces a smooth, transparent and warm sonic performance.
Facilities available on the DL241 include:
Expander/Gate : Drawmer\'s unique "Programmed Adaptive Expansion" circuitry allows effective \'single control operation\' producing a fast smooth response and eliminating \'chatter\' on or around threshold. This design differs from that of conventional Expanders in that the Expansion Ratio, Hold Attack and Release continually adapt themselves to the dynamics of the incoming signal. The Expander/Gate provides 80dB range and variable threshold from +20dB to 70dB with an OFF position. Switching is provided for \'Fast\' or \'Slow\' release characteristics. The \'Fast\' mode can be used for instruments with rapid decay times or for additional tightening of the gating effect. The \'Slow\' mode is more suitable for vocals and instruments with longer decay times or can be used to smooth over rough fade outs. A single LED indicates gating action.
Compressor : A full Auto Attack/Release Compressor with variable Threshold and Ratio successfully combines the smoothness of the \'Soft Knee\' principle with the precision of a \'Ratio\' control. The advantage of this combination is that instead of the onset of compression being sudden at the threshold point the ratio increases over a 10dB input level range until it reaches the ratio set on the front panel control, thus achieving a more natural sounding compression. Selectable manual or fully automatic Attack and Release times dramatically extend the application range and user scope of the DL241. Selecting the \'Auto\' mode removes the need for manual adjustment and is particularly valuable when the program being treated does not have predictable or consistent dynamics, often the case when processing a complete mix or a virtuoso bass guitar performance. Under manual control the wide range of adjustment available gives the user the ability to create dynamic effects as well as normal compression.
Peak Level. \'Zero Response Time\', \'Zero Overshoot\' circuitry : This provides an absolute limit to the peak level of the output signal, adjustable from OdB to +16dB above system level. When set to the required level, any excessive peaks will be stopped and the gain momentarily decreased if necessary. The \'Zero Response Time\' is essential to avoid unpleasant distortion when mastering for CD or sending any signal to digital equipment. \'Zero Response Time\' means that the DL241 provides complete protection from even the fastest and shortest signal \'spikes\' (overloads), making the unit also ideally suited for speaker system protection in sound reinforcement applications.
Metering : Comprehensive bar graph displays give \'at a glance\' indications of gain reduction, and output signal level Gain reduction from 1dB to -30dB is shown simultaneously with signal level from -20dB to +15dB Other single LEDs indicate function status of Gating Acton, Auto Mode, Bypass, Peak Limiting, Stereo Linking, and Power On.
Stereo Link : When processing stereo signals, linking should be used to prevent image shifting. This facility ties both channels together. Using channel 1 (left) as the master channel removes the need to duplicate control settings for both channels.
Bypass : A fully balanced hard-wire bypass connects the input directly to the output allowing signal to pass through the unit with no power applied. In bypass the VU level meter displays the Input signal.
Operating Level : The operating level of the DL241 can be instantly switched, independently on each channel, for either +4dBu or -10dBu operation using a rear panel push switch.
Input/Output : The DL241 is available with either XLR connections and fully balanced inputs and outputs, or with stereo jack (TRS) connections, fully balanced inputs and single ended outputs. |
Features
Enhance switch to restore spectral balance of compressed signal
Switchable Mode - Dual Channel or Stereo linked
Above or Below Threshold LEDs
Balanced XLR and Jack Inputs and Outputs
Intuitive, user friendly layout
Flawless performance
Innovation
The ARX COMPO? is a unique compressor/limiter designed for use in any
professional audio dynamics control application, packaged in a compact 1
RU chassis.The COMPO operates as two independent compressor/limiters,
with 'industry standard' variable Threshold, Ratio and Output gain controls.
A Stereo Link switch on the front panel lets both channels track as a stereo
pair in a Master/Slave configuration.
Enhance Switch
The COMPO features an 'Enhance' switch, which provides frequency restoration
to preserve the spectral balance of the audio signal, compensating for the sagging
Low and High frequency response of compressed program material.
The best way to think of it is as a 'smart' loudness control.
Wide Scale metering
There is comprehensive LED indication of all operating functions and status. Above
or Below Threshold LEDs on each channel give you instant visual confirmation of
compressor activity, as well as easy to read LED Gain Reduction meters.
Balanced Inputs and Outputs
On the rear panel, each channel has true differential Balanced inputs and outputs,
on both XLR and TRS jack connectors. Other features include an Active/Bypass
switch for each channel, and passive RFI filters on the inputs.
Universal AC Power
AC power range is a universal 100 to 120V or 220 to 240V AC, and is connected to
the unit via a removable power lead and standard 3 pin IEC connector, with built-in
fuse and voltage change switch.
ARX Quality
With its smooth compression, intuitive user friendly layout, high density precision
circuitry, and extensive user-variable operating parameters, the ARX COMPO is the
ideal installation 'set and forget' compressor, and is also equally at home in Studio,
Broadcast and Sound Reinforcement environments.
Every day, ARX Audio interface products solve audio problems for thousands of people
around the world.
T E C H N I C A L S P E C I F I C A T I O N S
Input Impedance Balanced 20 Kohms, Unbalanced 10 Kohms
Input Headroom + 22 dB
CMRR >60 dB, 20 Hz-20 KHz
Output Impedance Balanced 300 ohms, Unbalanced 150 ohms
Output Level (Max) + 22 dB
Frequency Response 20Hz to 20KHz ±0.4dB
Signal to Noise ratio -85 dB Unweighted, -99 dB 'A' weighted
Distortion .02% THD @ 0dB,1KHz
Dynamic Range 107 dB
Enhance Section
Low Enhance 50 Hz, High Enhance 10 KHz
Power Requirements 100/120 V AC, 220/240 V AC
Weight 5 lbs/2.2 Kg
Dimensions 19“W x 1?“H x 6“D, 482 x 44 x 155mm
Input/OutputConnector type XLR, Balanced Jack
Front Panel Controls
Channel A Active/Bypassed IN/OUT switch
Threshold, Ratio and Output Gain controls
Numbered marker panel for labelling compressor assigns
5 segment LED Gain Reduction display
Above/Below Threshold status LEDs
Enhance switch and status LED
Stereo link switch and status LED
Channel B controls identical to Channel A
Rear Panel Connectors
Balanced XLR Input and Output connectors.
Balanced TRS jack Input and Output connectors.
AC input connector, with voltage switch and fuse.
|
Features
Four Independent Compressor Channels
Channels 1 and 2, 3 and 4 are stereo linkable
7 LED Gain Reduction metering
Balanced XLR Inputs and Outputs
Sidechain Insert points
Intuitive, user friendly layout
Flawless performance
The sheer amount of effects and signal processors necessary for today's standards
of audio production puts a great strain on the available space in equipment racks,
both in the studio and on the road.So, ARX would like to introduce the ARX Quadcomp.
An all-new upgrade of the classic award-winning ARX Quadcomp?, the very first four
channel 1 RU compressor.You?ll notice that we haven?t strayed very far from our
original design concept. The Quadcomp is still four variable ratio Compressor/ Limiters
neatly housed in a compact all steel 1 RU package. However, all new low noise/low
distortion circuitry, better metering plus XLR inputs and outputs put the Quadcomp
in a class of its own.
More Control, Less Space
On the front panel, each channel has the 'industry standard' individual controls for Threshold,
Compression Ratio and Output, plus a new 7 LED Gain Reduction display for accurate visual
indication of the amount of gain reduction being applied to the program, and an IN/OUT
hardwire bypass switch.In addition to this, each channel has a blank numbered panel to write
on for easy confirmation of compressor assigns.
Precision Circuitry
Internally, each compressor uses Class A VCAs and true 2 pole averaging RMS/DC converters
for low distortion and accuracy, plus program dependent attack and release time, which
automatically determines optimum compressor response.
Balanced Inputs and Outputs
The rear panel has true differential Balanced XLR Inputs and Outputs for each compressor.
Each compressor has a TRS jack Sidechain access insert point, for frequency sensitive
compression, De-essing, etc. in conjunction with an external equalizer (such as the ARX EQ260).
Compressor pairs 1 and 2, 3 and 4 also have rear panel mounted Stereo Link switches for accurate
stereo tracking. When switched IN, the first channel becomes the master and controls all the functions
of the second except Output gain.
Universal AC Power
AC power range is switchable 100 to 120V, or 220 to 240V, and is connected to the unit via
a standard IEC connector, with built-in fuse and voltage switch.
Whatever the application ? Channel insert, Bus insert, Master Outputs, Monitor outputs,
Crossover outputs, the Quadcomp II?s unique High Density design, precision Low Noise circuitry
and clean uncluttered layout make it a truly useful audio tool for all applications.
T E C H N I C A L S P E C I F I C A T I O N S
Input Impedance
Balanced 20 Kohms, Unbalanced 10 Kohms
Input Headroom + 20dB
CMRR >50dB, 20 Hz?20 KHz
Output Impedance
Balanced 300 ohms Unbalanced 150 ohms
Output Level (Max) + 20 dB
Frequency Response 20Hz-20KHz ±0.5dB
Signal to Noise ratio
-93 dB Unweighted, -98 dB ?A? weighted
Distortion .015% THD @ 0dB,1KHz
Dynamic Range 108 dB
Attack and Release Times Program dependent
Metering
7 LED display: ?1, 2, 3, 6, 12, 18, ?24 dB
Sidechain Insert Impedance 10 Kohm
Power Requirements
100/120 V AC or 220/240 V AC
Weight 5 lbs/2.2 Kg
Dimensions
19“W x 1?“H x 6“D, 482 x 44 x 155mm
Input Connector type Balanced XLR
Output Connector type Balanced XLR
Sidechain Insert Connector TRS Jack
Front Panel Controls
Hardwire bypass IN/OUT switch
Threshold, Ratio and Output Gain controls
7 LED Gain Reduction display
Marker panel for labelling compressor assigns
Stereo link status LEDs
Rear Panel Connectors
Input and Output balanced XLR connectors
TipRingSleeve Sidechain insert connectors
Channels 1 and 2, 3 and 4 Stereo link switches
IEC AC mains connector with inbuilt fuse and
voltage change | L-1102 Leveler/Limiter
* Program dependent attack and release for transparent operation.
* Noise gate to cut off system background noise when there is no
signal.
* In limiter mode sense signal is from the amplifier output.
* Limits 4 ohm, 8 ohm, 25 V, 70 V and 100 V amplifier outputs.
* 20 dB gain in signal leveler mode.
* Security cover and rack-mount ears included.
* Five year warranty. |
The latest addition to the 10 Series product line, the dbx® 1074 QuadGate™, is the perfect companion to the 1066 and 1046. The 1074 offers 4 channels of gating with threshold, depth and release controls on each channel. The 1074, like the rest of the products in dbx 10 Series, is based on the legendary dbx V2 VCA and offers XLR inputs and outputs, and 1/4” side-chain input. In addition to an external key input per channel, the 1074 also has an internal filter that can be independently activated and controlled on a channel-per-channel basis. This filter allows the 1074 to not only clean up tracks, but gives you frequency selective control on each gate, to open exactly when you want it to. These features combined, make the 1074 an absolute must for those who require quad gating on applications including: Gating dry and percussive sounds such as snare drum and kick drum,gating sounds that have longer decay times such as cymbals and Pianos, gating hum or buzz from live instruments or recorded tracks or eliminating Headphone leakage into microphones. Gating instrument microphones to eliminate amplifier bleed.
From the company that has been redefining the standard of signal processing for more than 30 years, dbx® Professional Products comes a bulletproof product that caters to the scrutinizing needs of those who require the precision noise gating capabilities. Once again, the engineering staff at dbx® Professional Products have taken technology that has been over three decades in the making and have created a product that is flexible, versatile and rock solid in construction design. The 1074ʼs independent channel design with key filtering capabilities make it the perfect tool for countless applications.
- Four independent channels of gating
- Independent key filtering
- Independent Threshold and Release controls
- Differentially balanced gold-plated XLR and 1/4" inputs and outputs
- True RMS level detection
- Stereo Coupling mode
- Switchable +4dBu or -10dBv operation per channel
| Input Connectors | XLR (Pin 2 and tip hot) | | Input Type | Electronically balanced/unbalanced, RF filtered | | Input Impedance | Balanced > 50 kOhm, unbalanced >25 kOhm | | Max Input | > +22 dBu balanced or unbalanced | | CMRR | 40dB: Typically >55 dB at 1 kHz | | Key Input | Electronically balanced/unbalanced, RF fitered Balanced 50kOhm, unbalanced > 25 kOhm | | Output Connectors | XLR (Pin 2 hot) | | Output Type | Servo-balanced/unbalanced, RF filtered | | Output Impedance | Balanced 60 Ohm, unbalanced 30 Ohm | | Max Output | > +22 dBm balanced, > +20 dBm unbalanced | | Bandwidth | 20 Hz to 20 kHz, +0/-0.5 dB | | Frequency Response | 0.35 Hz to 200 kHz, +0/-3 dB | | Noise | | | Dynamic Range | > 115 dB, unweighted | | THD+Noise | 0.008% typical at +4 dBu (1 kHz unity gain), 0.08% typical at +20 dBu (1 kHz unity gain), | | Interchannel Crosstalk | | | Stereo Coupling | True RMS Power Summing | | Operating Voltage | 100-120 VAC 50-60 Hz or 200-240 VAC 50/60 Hz | | Power Consumption | 30 Watts | | Fuse | 100-120 VAC:250 mA Slow Blow, 200-240 VAC:125 mA Type T | | Power Connector | IEC receptacle | | Unit Weight | 6.9 lbs. | | Shipping Weight | 9.3 lbs. |
|
In today's recording and sound reinforcement environments, the need for multiple channels of high quality, easy to use compression is growing rapidly. The new dbx® 1046 is designed to provide the audio professional with just that: 4 channels of great sounding dbx compression for a variety of applications. Incorporating the industry standard dbx designs and the latest available manufacturing techniques, the dbx 1046 provides pristine sonic quality with that classic dbx sound.
The 1046 provides 4 channels of smooth classic dbx OverEasy® or Hard Knee compression that are perfectly suited for use on individual tracks of your multitrack recorder, and in virtually all applications the separate channels can be individually interfaced and used for entirely independent purposes. Additionally the newly developed PeakStopPlus™ is ideal for protecting your system from the oppressive peaks that can take out valuable drivers in your sound reinforcement rig or studio monitors.
All four channels have the following controls:
Threshold - allows you to set the level at which the compressor starts affecting the gain
OverEasy - allows you to select between soft compression for overall gain control or Hard Knee compression based on the characteristics of the original dbx 160.
Ratio - allows you to set the slope of gain reduction affecting the signal over the threshold level.
Input/Output Meter - allows you to set the meter to check the input and output levels for maximum signal-to-noise ratio and best level matching.
Output Gain - allows you to add make-up gain or to adjust the output level for that channel to match the next device's input gain.
Bypass - hard wire bypass allows you to hear how the compressor is affecting your signal.
PeakStopPlus - allows you to set the maximum signal level you want to pass through this channel. While it's virtually impossible to eliminate distortion, the PeakStopPlus circuit does it gracefully and effectively with minimal distortion.
Stereo Link - allows you to link channels 1&2 and 3&4 for two channels of true stereo compression.
All four channels feature balanced gold plated XLR and 1/4" inputs and outputs, and switchable +4dBu or -10dBV operating level to interface each individual channel with any other device.
So whether you need to control the level, placement in the mix, or overall characteristics of 4 independent signals or control the gain leveling on a couple of stereo pairs, the dbx 1046 is for you.
- Four independent channels of operation, stereo linkable in two pairs
- PeakStopPlus™ limiting control for setting maximum allowable level regardless of compressor settings
- Independent Threshold and ratio controls
- Switchable OverEasy® or Hard Knee compression
- Classic dbx® compression
- Differentially balanced gold-plated XLR and 1/4" inputs and outputs
- True RMS level detection
- Precision metering of input level, output level, and gain reduction
- Dual True stereo or quad mono operation
- Switchable +4dBu or -10dBV operation per channel
| Input Connectors | XLR and 1/4" TRS (Pin 2 and tip hot) | | Input Type | Electronically balanced/unbalanced, RF filtered | | Input Impedance | Balanced > 40 kOhm, unbalanced >20 kOhm | | Max Input | > +22 dBu balanced or unbalanced | | CMRR | Typically >50 dB at 1 kHz | | Output Connectors | XLR and 1/4" TRS (Pin 2 and tip hot) | | Output Type | Servo-balanced/unbalanced, RF filtered | | Output Impedance | Balanced 30 Ohm, unbalanced 15 Ohm | | Max Output | > +22 dBm balanced, > +20 dBm unbalanced | | Bandwidth | 20 Hz to 20 kHz, +0/-0.5 dB | | Frequency Response | 0.35 Hz to 90kHz, +0/-3 dB | | Noise | | | Dynamic Range | > 118 dB, unweighted | | THD+Noise | >0.008% typical at +4 dBu (1 kHz unity gain), 0.08% typical at +20 dBu (1 kHz unity gain), | | IMD | | | Interchannel Crosstalk | | | Stereo Coupling | True RMS Power Summing | | Compressor Threshold Range | -40 dBu to +20 dBu | | Compressor Ratio | 1:1 to infinity:1 | | Compressor Threshold Characteristic | Selectable OverEasy® or hard knee | | Compressor Attack/Release Characteristic | AutoDynamic™ | | Compressor Attack Time | Program-dependent | | Compressor Release Time | Program-dependent | | Compressor Output Gain | -20 to +20 dB | | Limiter Threshold Range | 0 dBu to +24 dBu (off) | | Limiter Ratio | infinity:1 | | Limiter Type | PeakStopPlus® two-stage limiter | | Limiter Stage 1 | PeakStop® brickwall limiter | | Limiter Stage 1 Attack Time | Zero | | Limiter Stage 1 Release Time | Zero | | Limiter Stage 2 | Predictive intelligent program limiter | | Limiter Stage 2 Attack Time | Program-dependent | | Limiter Stage 2 Release Time | Program-dependent | | OverEasy® Switch | Activates the OverEasy compression function | | I/O Meter Switch | Switches between monitoring input and output levels on the Input/Output Level meter | | Bypass Switch | Activates the direct input-to-output hard-wire bypass | | Operating Level Switch | (rear panel) Switches the nominal operating level between -10 dBV and +4 dBu simultaneously for both input and output levels | | ST Link Switch | Links channels in stereo pairs. Channels One and Three become the master channels | | Gain Reduction Meter | 8 segment LED bar graph at 1, 3, 6, 10, 15, 20, 25, and 30 dB | | I/O Meter | 8-segment LED bar graph at -24, -18, -12, -6, 0, +6, +12, and +18 dBu | | PeakStop™ Indicator | 1 LED to indicate PeakStop™ limiting | | Function Switches | LED indicator for each front-panel switch | | Output Transformer Options | Jensen® JT-123-dbx or JT- 11-dbx, BCI RE- 123-dbx or RE-11-dbx | | Operating Voltage | Switchable:100-120 VAC 50-60 Hz or 200-240 VAC 50/60 Hz | | Power Consumption | 20 Watts | | Fuse | 100-120 VAC:250 mA Slow Blow, 200-240 VAC:125 mA Type T | | Power Connector | IEC receptacle | | Dimensions | 1.75“Hx19“Wx9“D (4.4cmx48.3cmx20.1cm) | | Unit Weight | 5.2 lbs. (2.4 kg) | | Shipping Weight | 7.6 lbs. (3.5 kg) |
|
Reviews
There are no reviews yet.