The MX30 Pro Gated/Comp/Limiter is a low cost professional quality dynamics processor. Drawing on our many years experience in professional audio we have developed a series of lower-cost Drawmer dynamic signal processors, the MX Pro range. Aimed at the musician, project studio and live performer, who is determined not to compromise on quality, but have to work […]
The MX30 Pro Gated/Comp/Limiter is a low cost professional quality dynamics processor. Drawing on our many years experience in professional audio we have developed a series of lower-cost Drawmer dynamic signal processors, the MX Pro range. Aimed at the musician, project studio and live performer, who is determined not to compromise on quality, but have to work to a tighter budget.
By using circuit elements drawn from existing top-of-the-line Drawmer products and by simplifying the control systems where possible, the MX Pro range is no less sophisticated than our other units, despite the price tag. As a result the inexperienced user gains the benefits of Drawmer quality and performance, combined with lower cost and simplicity of operation.
Operational control is split into three sections:- Gate, Compressor, Output:
Programme Adaptive’ Gate
Used to remove unwanted noise below a pre-set level, each channel consists of a variable Threshold Gate incorporating Drawmer’s ‘Programme Adaptive’ circuitry. Although quick and simple to operate, the gate’s auto-circuitry continually optimises such parameters as Attack, Hold, Ratio and Release, completely eliminating ‘chatter’ when the signal is fluctuating on or around Threshold. Two LEDs show when the signal is ‘above’ or ‘below’ Threshold and a push button switch allows additional control of Release time. This design approach also retains all ‘leading edge’ information making the gate ideal for ‘cleaning up’ vocals or retaining the ‘punch’ on gated drums. Switching is provided for \’Fast\’ or \’Slow\’ release characteristics. The \’Fast\’ mode can be used for instruments with rapid decay times or for additional tightening of the gating effect. The \’Slow\’ mode is more suitable for vocals and instruments with longer decay times or can be used to smooth over rough fade outs. A single LED indicates gating action.
Soft Knee ‘Auto Compressor’
The gate is followed by a variable Threshold, variable Ratio, soft knee compressor with fully automatic Attack and Release. Large transients are controlled instantly whilst small signal variations are treated gently, retaining as much ‘life’ as possible and without generating unpredictable side effects. the MX30 Pro handles all compression levels with ease and displays the amount of compression on a high resolution Gain Reduction bargraph meter.
Output
The Gain control is used to compensate for the amount of compression and brings the signal to the required output level as displayed by the output bargraph meter. A variable Threshold ‘zero overshoot’ limiter, essential for avoiding distortion when mastering to digital or speaker protection in a ‘live’ situation, adds the final polish to the signal by keeping control over signal peaks. The Limit threshold provides an absolute maximum peak level which no signal can pass. Fast transients are clipped instantly whilst more sustained peaks are dealt with by applying Gain Reduction, indicated by a single LED.
Gate Threshold:
This control sets the level below which gating takes place and may be set anywhere in the range of -70dB to +20dB. A green LED illuminates to show when the signal is above threshold (i.e. gate open) and a red LED illuminates when the signal is below Threshold (i.e. gate closed).
Release: Either a Fast or Slow auto release contour may be selected depending on the material being processed. An LED indicates when Slow release status is engaged. Percussive material with little or no reverb is generally treated using the Fast release setting, whereas with slow decays or a significant amount of added reverb will usually respond better to the Slow release setting.
Compressor Threshold: This determines the input level above which gain reduction will be applied and may be set anywhere in the range of -40dB to +20dB. Soft Knee compression takes place for signals exceeding the threshold level by up to 10dB above which level, conventional ‘ratio’ compression is applied.
Gain Reduction Bargraph Meter: A nine segment LED bargraph meter continuously monitors the gain reduction applied by the compressor over a range of 0dB to 30dB.
Ratio: Sets the final compression ratio that will be applied once the 10dB soft knee region is exceeded. The ratio may be continuously adjusted from 1.2:1 to infinity:1 allowing the possibility of true hard limiting. The higher the ratio setting the more compression takes place (eg. A ratio of 8:1 means that an 8dB increase in volume at the input will appear as a 1dB increase in volume at the output).
Stereo Link: The unit can function as two independent gated/compressor/limiters or when ‘link’ mode is engaged for stereo use Channel 1 becomes the master, automatically duplicating its parameters across to Channel 2. In this mode the same degree of gain reduction is applied to both audio channels to prevent image shifting.
Output Gain: The output level may be attenuated or amplified by up to 20dB to compensate for level changes caused by compression. This control comes directly before the Peak Limiter detector and this fact should be taken into account when setting the Peak Limiter threshold.
Peak Limit: This control sets an absolute limit that the output signal will not be permitted to exceed. The limiter is ‘zero response time’ and controls peaks without any audible distortion. For transparent ‘peak protection’ the output gain control should be set to ensure that the Peak Limiter operates only occasionally. Alternatively, the unit can be driven into heavy limiting for creative effects.
Input/Output Bargraph Meter: An eight segment LED bargraph level meter monitors the output signal level over a range of -20dB to +15dB. When Bypass is selected this meter reads input level.
Weight
3.20 kg
Reviews
There are no reviews yet.
Be the first to review “DRAWMER MXPRO 30 2-Channel Gate / Compressor / Limiter2-Channel Gate / Compressor / Limiter” Cancel reply
The MX30 Pro Gated/Comp/Limiter is a low cost professional quality dynamics processor. Drawing on our many years experience in professional audio we have developed a series of lower-cost Drawmer dynamic signal processors, the MX Pro range. Aimed at the musician, project studio and live performer, who is determined not to compromise on quality, but have to work to a tighter budget.
By using circuit elements drawn from existing top-of-the-line Drawmer products and by simplifying the control systems where possible, the MX Pro range is no less sophisticated than our other units, despite the price tag. As a result the inexperienced user gains the benefits of Drawmer quality and performance, combined with lower cost and simplicity of operation.
Operational control is split into three sections:- Gate, Compressor, Output:
Programme Adaptive’ Gate
Used to remove unwanted noise below a pre-set level, each channel consists of a variable Threshold Gate incorporating Drawmer’s ‘Programme Adaptive’ circuitry. Although quick and simple to operate, the gate’s auto-circuitry continually optimises such parameters as Attack, Hold, Ratio and Release, completely eliminating ‘chatter’ when the signal is fluctuating on or around Threshold. Two LEDs show when the signal is ‘above’ or ‘below’ Threshold and a push button switch allows additional control of Release time. This design approach also retains all ‘leading edge’ information making the gate ideal for ‘cleaning up’ vocals or retaining the ‘punch’ on gated drums. Switching is provided for \'Fast\' or \'Slow\' release characteristics. The \'Fast\' mode can be used for instruments with rapid decay times or for additional tightening of the gating effect. The \'Slow\' mode is more suitable for vocals and instruments with longer decay times or can be used to smooth over rough fade outs. A single LED indicates gating action.
Soft Knee ‘Auto Compressor’
The gate is followed by a variable Threshold, variable Ratio, soft knee compressor with fully automatic Attack and Release. Large transients are controlled instantly whilst small signal variations are treated gently, retaining as much ‘life’ as possible and without generating unpredictable side effects. the MX30 Pro handles all compression levels with ease and displays the amount of compression on a high resolution Gain Reduction bargraph meter.
Output
The Gain control is used to compensate for the amount of compression and brings the signal to the required output level as displayed by the output bargraph meter. A variable Threshold ‘zero overshoot’ limiter, essential for avoiding distortion when mastering to digital or speaker protection in a ‘live’ situation, adds the final polish to the signal by keeping control over signal peaks. The Limit threshold provides an absolute maximum peak level which no signal can pass. Fast transients are clipped instantly whilst more sustained peaks are dealt with by applying Gain Reduction, indicated by a single LED.
Gate Threshold:
This control sets the level below which gating takes place and may be set anywhere in the range of -70dB to +20dB. A green LED illuminates to show when the signal is above threshold (i.e. gate open) and a red LED illuminates when the signal is below Threshold (i.e. gate closed).
Release: Either a Fast or Slow auto release contour may be selected depending on the material being processed. An LED indicates when Slow release status is engaged. Percussive material with little or no reverb is generally treated using the Fast release setting, whereas with slow decays or a significant amount of added reverb will usually respond better to the Slow release setting.
Compressor Threshold: This determines the input level above which gain reduction will be applied and may be set anywhere in the range of -40dB to +20dB. Soft Knee compression takes place for signals exceeding the threshold level by up to 10dB above which level, conventional ‘ratio’ compression is applied.
Gain Reduction Bargraph Meter: A nine segment LED bargraph meter continuously monitors the gain reduction applied by the compressor over a range of 0dB to 30dB.
Ratio: Sets the final compression ratio that will be applied once the 10dB soft knee region is exceeded. The ratio may be continuously adjusted from 1.2:1 to infinity:1 allowing the possibility of true hard limiting. The higher the ratio setting the more compression takes place (eg. A ratio of 8:1 means that an 8dB increase in volume at the input will appear as a 1dB increase in volume at the output).
Stereo Link: The unit can function as two independent gated/compressor/limiters or when ‘link’ mode is engaged for stereo use Channel 1 becomes the master, automatically duplicating its parameters across to Channel 2. In this mode the same degree of gain reduction is applied to both audio channels to prevent image shifting.
Output Gain: The output level may be attenuated or amplified by up to 20dB to compensate for level changes caused by compression. This control comes directly before the Peak Limiter detector and this fact should be taken into account when setting the Peak Limiter threshold.
Peak Limit: This control sets an absolute limit that the output signal will not be permitted to exceed. The limiter is ‘zero response time’ and controls peaks without any audible distortion. For transparent ‘peak protection’ the output gain control should be set to ensure that the Peak Limiter operates only occasionally. Alternatively, the unit can be driven into heavy limiting for creative effects.
Input/Output Bargraph Meter: An eight segment LED bargraph level meter monitors the output signal level over a range of -20dB to +15dB. When Bypass is selected this meter reads input level.
The DPR-504 is a 4-channel noise gate.
Each channel features: A parametric key filter with key filter listening. Simultaneous key level and threshold metering with average and peak metering. A gate status LED. A RELEASE/HOLD control (hold tracks proportionally with release times). Attack switchable auto/fast (auto tracks signal dynamics for optimum setting). Link (links two channels together). Key source allows external triggers.
The Range switch selects between 7OdB and 2OdB gating depth to provide alternative release profiles. The unit features electronically balanced inputs and outputs.
Features Enhance switch to restore spectral balance of compressed signal Switchable Mode - Dual Channel or Stereo linked Above or Below Threshold LEDs Balanced XLR and Jack Inputs and Outputs Intuitive, user friendly layout Flawless performance
Innovation The ARX COMPO? is a unique compressor/limiter designed for use in any professional audio dynamics control application, packaged in a compact 1 RU chassis.The COMPO operates as two independent compressor/limiters, with 'industry standard' variable Threshold, Ratio and Output gain controls. A Stereo Link switch on the front panel lets both channels track as a stereo pair in a Master/Slave configuration. Enhance Switch The COMPO features an 'Enhance' switch, which provides frequency restoration to preserve the spectral balance of the audio signal, compensating for the sagging Low and High frequency response of compressed program material. The best way to think of it is as a 'smart' loudness control. Wide Scale metering There is comprehensive LED indication of all operating functions and status. Above or Below Threshold LEDs on each channel give you instant visual confirmation of compressor activity, as well as easy to read LED Gain Reduction meters. Balanced Inputs and Outputs On the rear panel, each channel has true differential Balanced inputs and outputs, on both XLR and TRS jack connectors. Other features include an Active/Bypass switch for each channel, and passive RFI filters on the inputs. Universal AC Power AC power range is a universal 100 to 120V or 220 to 240V AC, and is connected to the unit via a removable power lead and standard 3 pin IEC connector, with built-in fuse and voltage change switch. ARX Quality With its smooth compression, intuitive user friendly layout, high density precision circuitry, and extensive user-variable operating parameters, the ARX COMPO is the ideal installation 'set and forget' compressor, and is also equally at home in Studio, Broadcast and Sound Reinforcement environments.
Every day, ARX Audio interface products solve audio problems for thousands of people around the world.
T E C H N I C A L S P E C I F I C A T I O N S Input Impedance Balanced 20 Kohms, Unbalanced 10 Kohms Input Headroom + 22 dB CMRR >60 dB, 20 Hz-20 KHz Output Impedance Balanced 300 ohms, Unbalanced 150 ohms Output Level (Max) + 22 dB Frequency Response 20Hz to 20KHz ±0.4dB Signal to Noise ratio -85 dB Unweighted, -99 dB 'A' weighted Distortion .02% THD @ 0dB,1KHz Dynamic Range 107 dB Enhance Section Low Enhance 50 Hz, High Enhance 10 KHz Power Requirements 100/120 V AC, 220/240 V AC Weight 5 lbs/2.2 Kg Dimensions 19“W x 1?“H x 6“D, 482 x 44 x 155mm Input/OutputConnector type XLR, Balanced Jack
Front Panel Controls Channel A Active/Bypassed IN/OUT switch Threshold, Ratio and Output Gain controls Numbered marker panel for labelling compressor assigns 5 segment LED Gain Reduction display Above/Below Threshold status LEDs Enhance switch and status LED Stereo link switch and status LED Channel B controls identical to Channel A Rear Panel Connectors Balanced XLR Input and Output connectors. Balanced TRS jack Input and Output connectors. AC input connector, with voltage switch and fuse.
FEEDBACK DESTROYER FBQ1000
Automatic and Ultra-Fast Feedback Destroyer/Parametric EQ with 24 FBQ Filters
High-performance 2-channel Feedback Destroyer and Parametric EQ
Automatically and "intelligently" locates and destroys up to 24 frequencies
Ultra-narrow FBQ filters for extremely effective feedback suppression, while keeping highest sonic quality
"Set-and-forget" default setting enables immediate and super-easy Feedback Destroyer performance
Auto mode continuously monitors the mix and automatically sets filters
Single-Shot mode automatically detects and destroys feedback plus locks the filter until you reset it manually
Manual mode allows setting of up to 24 fully parametric filters with individual frequency, bandwidth and gain parameters
Extensive MIDI implementation and user preset memories for instant program recalls
Balanced inputs and servo-balanced outputs with ¼'' TRS and gold-plated XLR connectors
High-quality components and exceptionally rugged construction ensure long life
Conceived and designed by BEHRINGER Germany
BEHRINGER FEEDBACK DESTROYER FBQ1000
L-1102 Leveler/Limiter
* Program dependent attack and release for transparent operation.
* Noise gate to cut off system background noise when there is no
signal.
* In limiter mode sense signal is from the amplifier output.
* Limits 4 ohm, 8 ohm, 25 V, 70 V and 100 V amplifier outputs.
* 20 dB gain in signal leveler mode.
* Security cover and rack-mount ears included.
* Five year warranty.
The S com 4 is a compact and versatile single-rack space device that provides
four channels of high quality dynamics processing with an Expander/Gate and
Compressor/Limiter on each channel.
The four channels operate independently or in stereo pairs. Its multi-segment LED
metering displays input/output level as well as gain reduction. The Expander/Gate
section features a continuously variable Threshold control as well as a switch for
fast or slow release times.
The Compressor/Limiter section includes variable Threshold, Ratio and Output levels.
S com 4's Enhancer switch restores high frequencies that are sometimes diminished
by heavy compression. This wide-ranging combination of features makes the S com
4 an efficient and versatile audio tool for a wide variety of applications. Its clean and
quiet audio characteristics make it ideal where high sonic integrity is imperative.
FEATURES:
4 Channel Compressor/Limiter, Expander/Gate with Enhancer
Linkable in two Stereo pairs
Expander/Gate with variable Trigger control and switchable Fast/Slow Release
5 Segment LED meters for Input/Output levels and Gain Reduction on each channel
Advanced circuit design utilizing Low Noise Operational
Amplifiers and High Quality VCA's
Servo Balanced Inputs and Outputs on XLR and 1/4" connectors
SKD (Smart Knee Detector) circuit automatically switches from soft to hard knee
based on the level of Input signal applied
Individual Threshold and Ratio controls on each channel
Three-year extended warranty
This website uses cookies to improve your experience. We'll assume you're ok with this, but you can opt-out if you wish. Cookie settingsACCEPT
Privacy & Cookies Policy
Πολιτική χρήσης
Αυτός ο ιστότοπος χρησιμοποιεί cookies για να βελτιώσει την εμπειρία σας ενώ περιηγείστε στον ιστότοπο. Από αυτά τα cookies, κάποια cookie κατηγοριοποιούνται ως απαραίτητα να αποθηκεύονται στο πρόγραμμα περιήγησης σας, καθώς είναι απαραίτητα για τη λειτουργία βασικών λειτουργιών του ιστότοπου. Χρησιμοποιούμε επίσης cookies τρίτων που μας βοηθούν να αναλύσουμε και να κατανοήσουμε πώς χρησιμοποιείτε αυτόν τον ιστότοπο. Αυτά τα cookies θα αποθηκευτούν στο πρόγραμμα περιήγησης σας μόνο με τη συγκατάθεσή σας. Έχετε επίσης την επιλογή να εξαιρεθείτε από αυτά τα cookies. Ωστόσο, η εξαίρεση από ορισμένα από αυτά τα cookie μπορεί να επηρεάσει την εμπειρία περιήγησης σας.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.
Reviews
There are no reviews yet.