DYNACORD H-5000 POWER AMPLIFIER 2x 2500 Watt / 4 Ohm

Dynacord H 5000

 
The power amp H5000 is part of Dynacord´s new PowerH SERIES, which marks a milestone in the design and the production of high-performance power amplifiers. The innovative 3-stage Grounded Bridge Class H Topology with "floatingË switching power supply unit offers very high and stable output with extreme high efficiency on an extremely high performance level at minimum weight. PowerH amps are ideal for driving professional touring, high-end Concert-Sound and Pro-Sound applications.  

 
Dynacord H 5000 features:

    2x 1500 Watt / 8 Ohm
    2x 2500 Watt / 4 Ohm
    2x 3500 Watt / 2 Ohm
    Cooling: Front-to-Rear, 5-stage-fans
    Dimensions (WxHxD): 483 x 88.1 x 498 mm
    Weight: 14.5 kg
    Protections:
    Audio limiters
    High temperature
    DC
    HF
    Short Circuit
    Back-EMF
    Peak current limiters
    Inrush current limiters
    Turn-on delay
    Mains Circuit Breaker Protection
    Mains Overvoltage Protection

The new Audio 3-stage CLASS-H SMPS amplifiers incorporate all the features to meet all your needs, whether youʼre starting a P.A. amplifier project from scratch or just need to upgrade your present sound reinforcement equipment. In the amps, youʼll find 2 and 4 channel models, all offering high power levels at low distortion in the range 1.5 to 6 kW, yet weighing around 8.6 kg and only 30 cm deep.

• Model Name: SP6K
• Output Power 1 kHz, 500
• Crosstalk (20 Hz - 20 kHz): > 75 dB
• Voltage Gain (selectable): 26 / 32 / 38 dB
• Input Sensitivity: 5.0 / 2.5 / 1.3 V
• Protection: Soft-start, Turn-on Turn-off transients, Muting at turn-on, Over-heating, DC, RF, Short-circuit, Open or mismatched loads, Overloaded power supply, ICL (Inteligent Clip Limiting), PMS (Power Management System), SSP (SOA Sentry Protection)
• Controls: On / Off Switch, Volume, Voltage Gain, Dual / Link Switchable, Bridge Mode Configuration Switch
• Indicators: Signal, Temperature, ICL (Inteligent Clip Limiting), PMS (Power Management System)
• Connectors:
  • Input: 2 x XLR
  • Line Output: 2 x XLR
  • Speaker Output: 2 x Speakon
• Power Supply: 230 V - 50 Hz
• Dimensions (W x H x D): 483 × 88.9 × 310 mm

Features

• The i Series continues the Macro-Tech legacy of unparalleled sonic accuracy and detail, putting sound quality above all else
• Patented, cutting-edge Class-I circuitry gets more power out of an amplifier with less waste
• Rugged construction ensures that all Macro-Techs are built to withstand years of abuse on the road
• Global Power Supply - designed to deliver maximum power no matter where your schedule takes you
• Studio-quality analog signal processing with built-in load, line voltage, input and output monitoring
• Standard Ethernet networking via System Architect provides integratedmonitoring and control to give system operators access to the system from anylocation

Power Output (Guaranteed minimum power in watts at 20Hz-20kHz with 0.35% THD)

• 2 ohm dual (per ch), 20 mS BURST: 2,565W
• 2 ohm dual (per ch), 20Hz-20kHz: 1,800W
• 2 ohm dual (per ch), 1kHz: 1,800W
• 4 ohm dual (per ch): 2,000W
• 8 ohm dual (per ch): 1,250W
• 4 ohm bridge: 3,600W
• 8 ohm bridge: 4,000W

Performance

• Frequency Response (at 1 watt, 20 Hz - 20 kHz into 8 ohms): ±0.25 dB.
• Signal to Noise Ratio below rated full-bandwidth power, A-weighted: > 108 dB.
• Total Harmonic Distortion (THD) at 1 watt into 8 ohms:
• Total Harmonic Distortion (THD) Plus Noise at full rated power:
• Intermodulation Distortion (IMD) 60 Hz and 7 kHz at 4:1, from full rated output to –30 dB:
• Damping Factor (20 Hz to 100 Hz at 8 ohms): > 5000.
• Crosstalk (below rated power, 20 Hz to 1 kHz): > 80 dB.
• Common Mode Rejection (CMR) (20 Hz to 1 kHz): 55 dB, typically >70 dB.
• DC Output Offset (shorted input):
• Input Impedance (nominal): 10 kilohms balanced, 5 kilohms unbalanced.
• Maximum Input Level: +20 dBu typical.
• Network: Onboard TCP/IQ and HiQnet, compatible with standard 100 Mb Ethercom hardware.
• Load Impedance: (Note: Safe with all types of loads) Stereo: 1/2/4/8/16 ohms. Bridge Mono: 2/4/8 ohms.
• Input Sensitivity (referenced to 8 ohm rated output): 1.4V, 32 dB gain, and 26 dB gain.
• Voltage Gain (referenced to 8 ohm rated output): 37.1 dB to 22.2 dB
• Required AC Mains: Universal AC input, 100-240VAC, 50/60 Hz (±15%). Maximum AC mains voltage 264VAC.
• AC Line Connector: Five cordsets supplied with amplifi er (USA, UK,European, Australia, India).

Front Panel Controls and Indicators

• Bridge Mode Indicator: Amber LED illuminates when the amplifi er is set to Bridge-Mono mode.
• Ready Indicator: Red LED, one per channel. Bright red: Channel is ready to pass audio. Red: Onset of compression (thermal event or fan failure). Off: Thermal event has occurred.
• Signal Indicators: One green LED per channel. Solid green: Input signal is above –40 dBu. Bright green: Channelʼs output signal has reached the onset of audible clipping.
• Power Indicator: Blue LED indicates amplifier has been turned on and AC power is available. The LED will fl ash when the AC line voltage is 10% above or below the nominal rated value.
• Data Indicator: Yellow LED on front panel indicates network data activity. Data indicator flashes only when the amplifier is polled for data, or is polled to see whether it is online
• Power Switch: Push-on/push-off switch with built-in green AC mains present indicator.
• Volume Control: Precision detented attenuator with 31 steps, press-and-hold mute function.
• Volume Control LED Ring: A ring of green LEDs around each volume controlshow the position of the control. Entire ring flashes when channel is muted.Can be converted to be a level meter.

Back Panel Controls, Indicators and Connectors

• Power Cord Connector: Locking, detachable 20 amp IEC inlet. Voltage range is indicated above IEC inlet.
• Reset Switch/Circuit Breaker: If the current draw of the amplifier exceeds safe limits, this breaker automatically disconnects the power supply from the AC mains. The switch resets the circuit breaker.
• Output Connectors: Two high-current, 50A Neutrik® Speakon® NL4MLP (mates with NL4FC or NL4), one per channel. Ch 1 Speakon® is wired with Ch 1 and Ch 2 outputs for use with single 4-conductor cable. Two pairs of high-current, 60A color-coded 5-way binding posts (for banana plugs, spade lugs or bare wire).
• Analog Input Connectors: A 3-pin female XLR connector for each channel.
• Analog Loop Thru Connectors: Two male XLR passive analog loop through.
• Mode Switch/Indicator: Sets amplifi er to Stereo, Bridge, or Input Y mode. OFF=Stereo, YEL=Bridge, GRN=Y.
• Network Connector: This Neutrik® Ethercon connector accepts an RJ-45 connector for TCP/IQ or HiQnet networking. Next to the connector is a yellow LINK ACT indicator that shows network activity, and a green 100Mb indicator that shows a 100Mb network connection.
• Data Indicator: Yellow LED on back panel indicates network data activity. Data indicator flashes only when the amplifi er is polled for data, or is polled to see whether it is online.
• Preset Indicator: Yellow LED flashes to signal the number of the current preset if active.
• Input Sensitivity Switch: Three-position switch providing 1.4V, 32 dB, and26 dB settings for both channels.

Firmware/Software

• Firmware can be updated at www.crownaudio.com > Support > Downloads.
• Software features: Same as PIP-Lite module (except no Listen Bus): UserPresets, Clip Event Monitor, Input Signal Level Monitor, Output Signal LevelMonitor, Thermal Headroom Level Monitor, Power/Standby Control, Signal Mute,Polarity Inverter, Input Signal Fader, Dynamic Gain Monitors (Ghost Faders),Amplifier Information, User and Channel Labels, Amplifier Mode, AmplifierOutput Mode, Line Voltage Monitor, Error Reporting, Auto Standby, Input SignalCompressor/Limiter, Peak Voltage Limiter, Average Power Limiter, ClipEliminator, Thermal Limiter, Limiter Tie, Load Supervision.

Construction

• Cooling: Dual-zone, microprocessor controlled, continuously variable speed fans, front-to-back airflow.
• Front Panel: Cast aluminum with integrated handles.
• Dimensions (W x H x D): 19" x 3.5" x 16.2"
• Weight: 28 lbs net, 36 lbs shipping
• Protection: Amplifi er is protected against reactive loads, faults and shorts. If one channel experiences a catastrophic failure, the entire amplifier will shut down.
• Included Accessories: Rear rack ears, rack screws, operation manual, powercords, foam air filter.

Crown CDi Series amplifiers are professional tools designed and built for installed sound applications. The series includes four models which are identical except for output power: CDi 1000, CDi 2000, CDi 4000, and CDi 6000. All are rugged and lightweight, and offer unmatched value in their class.

• Extremely versatile; rated for 2-, 4-, 8-ohm loads and 70V and 140V outputs.
• Switch-mode universal power supply.
• Intuitive front-panel LCD screen for quick, easy configuration.
• Onboard digital signal processing includes crossovers, EQ filters, delay, and output limiting.
• Up to 20 user defined DSP presets are available.

Model T4n
Product Type Power Amplifier
Output Power (W) 1kHz THD+N=1% (120V)
2Ω per channel 2200
4Ω per channel 1950
8Ω per channel 1150
4Ω bridge 4400
8Ω bridge 3900
Output Power (W) 1kHz 20mS burst (120V)
2Ω per channel 2900
4Ω per channel 1950
8Ω per channel 1150
4Ω bridge 5800
8Ω bridge 3900
SN ratio (20Hz-20kHz) 106dB

THD+N 20Hz-20kHz, Half Power RL-4Ω, 8Ω
Intermodulation Distortion 60Hz: 7kHz, 4:1, Half Power 0.1%
Frequency response RL=8Ω,Po=1W,HPF=OFF 20Hz-20kHz (Max) 0dB
Frequency response RL=8Ω,Po=1W,HPF=OFF 20Hz-20kHz (TYP) 0dB
Frequency response RL=8Ω,Po=1W,HPF=OFF 20Hz-20kHz (MIN) 6dB
Channel Separation (Half Power RL=8Ω,1kHz Att. max input 600Ω shunt) 70dB
Residual Noise Att,min 20Hz-20kHz(DIN AUDIO) -70dBu
Damping factorRL=8Ω 1kHz 800
Voltage Gain Att.max 26dB
Maximum Input Voltage +24dBu
Input Impedence 20kΩ (balance) 10kΩ (unbalance)
Controls Specifications
Front Panel POWER switch(push on/push off) attenuator (31 position) x2
Rear Panel MODE switch (STEREO/BRIDGE/PARALLEL) X1; HPF switch (20Hz/OFF 12dB/oct) x1; AMP ID switch (6PDIP)x1
Connectors Specifications
Input XLR-3-31 type/ch; Euroblock connector (balance)/ch
Output SPEAKON/ch, 5way biding postx1
Date Port RJ45x2
Indicators Specifications
Power/Standby x1 (Green/Orange)
Remote x1 (Green)
Protection x1 (Red)
Temp x1 (Red) heatsink temp 85°C
Signal x2 (Green)
Mute x2 (Red)
Clip/Limit x2 (Red)
Load protection POWER switch on/off mute; DC-fault: power supply shutdown / do not return automatically
Cooling Variable-speed fan: x2
Power requirements 120V/60Hz
Weight 14.0 kg
Dimensions (W x H x D) 480 x 88 x 456mm (2U)

Power Output Level R-300 PLUS

STEREO
8ohm(T.H.D 0.05%)  170W+170W
4ohm(T.H.D 0.05%)  250W+250W

BRIDGED MONO
8ohm(T.H.D 0.05%)  460W
8ohm(T.H.D 0.5%)    500W

Frequency Response 20Hz- 20kHz, ±0.5dB

Convection Cooled

SoftStart Protection System

Balanced 10kΩ@0.775V Inputs