Content | Specifications :
- Type Back Electret Condenser
- Polar Pattern Omni-Directional
- Frequency Response 80Hz - 16KHz
- Sensitivity -52 + 3db
- Impedance 680 Ω
- Max.Input SPL 128db
- Power Requirement 1,5 - 10 vdc
- Cable Lenght 1 m
- Weight 5 g
- Capsule Diameter O 25
- Accessories Windscreen
- Available Connectors 3-pin mini XLR
| Subminiature lavalier design; ideal size for theater, television, broadcasting, video, film, and sound reinforcement
Small, inconspicuous mounting hardware
Full, clear sound comparable to larger microphones
Smooth extended frequency response with presence rise specially tailored for chest-worn microphone operation
Controlled low-frequency rolloff reduces low-frequency clothing and room noise
Low distortion, wide dynamic range
Uniform omnidirectional polar pattern
Preamplifier assembly (SM93) can be pocketed, strapped to the body, or clipped to belt or waistband
Wide-range phantom powering (SM93) accepts all commonly used voltages
Type
Condenser (electret bias)
Frequency Response
50 to 20,000 Hz
Response Curve Image Small SM93 WL93 View Larger
Polar Pattern
Omnidirectional, uniform with frequency
Output Impedance
3000 ohms
Output Level (1 Pascal = 94 dB SPL)
Open Circuit Voltage: -38 dBV/Pa (13 mV)
Output Clipping Level (at 1,000 Hz)
0.25 V at 120 dB
Total Harmonic Distortion
Less than 1% at 120 dB
Maximum SPL
120 dB
Dynamic Range (maximum SPL to A-weighted noise level)
102 dB
Output Noise (equivalent SPL)
18 dB typical, A-weighted
Signal-to-Noise Ratio
76 dB at 94 dB SPL (IEC 651)
Polarity
Positive pressure on microphone diaphragm produces positive voltage on pins 3 and 4 with respect to pin 1 (ground)*
*Produces positive voltage at pin 2 of Shure wireless receiver three-pin connector
Recommended Operating Voltage
2 to 10 V; 5 V nominal (pin 2 to pins 3 and 4)
Current Drain
40 microA typical
Environmental Conditions
Operating Temperatures: -18 to 57 degrees C (0 to 135 degrees F)
Storage Temperatures: -29 to 74 degrees C (-20 to 165 degrees F)
Cable
Black 1.27 m (4.17 ft), attached, two-conductor, shielded, terminated by miniature connector type TA4F (WL93T: Tan 1.27 m [4.17 ft])
Case
Microphone: Black ABS thermoplastic case with stainless-steel-mesh grille
Net Weight
Microphone: 16 g (0.57 oz) |
All models include foam windscreens, swiveling lapel clip, dual tie clip, magnet mount, and mini mount
Subminiature size (5.8 mm diameter x 11 mm height)
Electret condenser cartridge
Omnidirectional pattern
One termination: 4-pin mini connector (fits directly into Shure wireless transmitters)
Two sensitivities available:
--Standard: -40 dBV/Pa (for speech applications)
--Reduced: -50 dBV/Pa (10 dB more headroom for theater applications)
Interchangeable equalization caps for optimal clarity and response:
--Silver mesh cap provides a 4 dB boost in the 8-18 kHz range - typically used in applications that require a microphone to be head-mounted
--Gold mesh cap provides a 10 dB boost centered at 12 kHz - typically used in applications that require a chest-worn microphone
Black, beige, and white models are available
All models include magnet mount, lapel clip, dual tie clip, pin mount, and two foam windscreens
Frequency response: 20-20,000 Hz
|
The Shure MX150 Subminiature Lavalier Microphone is a subminiature, multi-positioned clip-on microphone well suited for broadcast operation, sermons, presentations, public address and much more. This version includes the RK100PK XLR in-line preamplifier for use with standard XLR connections in mixers, recorders, mic-pres, etc. Shure's CommShield technology makes the MX150 impervious to noise caused by cell phones, PDAs, WiFi and other RFI. The microphone ships with a snap-fit foam windscreen and multi-position tie clip with an integrated cable management system that minimizes noise without increasing cable strain and tension. Omnidirectional polar pattern and wired XLR connection CommShield Technology guards against interference from cellular RF devices and digital bodypack transmitters Matte black, sleek design for inconspicuous placement Multi-position tie clip allows for a variety of placement options and features an integrated cable management system for convenient cable dress with minimal handling noise Kevlar-reinforced soft-flex cable design further reduces handling noise while providing superior flexibility for routing and placement User-changeable equalization caps for response shaping (omnidirectional only) Snap-fit, concise windscreen provides protection from plosives and wind noise with minimal visibility Legendary Shure quality, ruggedness, and reliability Transducer | Electret condenser | Polar Pattern | Omnidirectional | Frequency Response | 20 to 20,000Hz | Output Impedance | 165.0 Ω | Sensitivity | -34.5 dBV/Pa (19.0 mV) | Max Input Sound Level (SPL) | 1000 Ω load: 125.0 dB SPL; 2500 Ω load: 130.0 dB SPL | Signal-to-Noise Ratio | 59.5 dB | Dynamic Range | @1kHz 1000 Ω: 90.5 dB SPL; 2500 Ω load: 95.5 dB SPL | Self Noise | 34.5 dB (equivalent SPL, A-weighted, typical) | Clipping Level | 1000 Ω load: 1.0 dBv; 2500 Ω load: -4.5 dBv | Operating Temperature | Operating: 0 to 135°F (-18 to 57°C) Storage: -20 to 165°F (-29 to 74°C) | Polarity | XLR: Positive pressure on diaphragm produces positive voltage on pin 2 with respect to pin 3 | Power Requirements | 11-52VDC phantom power (IEC-61938), | Dimensions (LxDiameter) | Length: 5' (1.52m) Diameter: 0.23" (5.8mm) | Weight | 4.3 oz (121 g) |
|
Miniaturized lavalier condenser microphone for wireless or wired applications.
The ADX10 is a miniaturized condenser microphone designed for lavaliere applications such as speech, presentation and theatrical production. The ADX10 has the ability to accurately capture and reproduce vocals from a comfortable distance of 4“- 8“. This mic is clear, resistant to feedback and easy to use.
Designed with a uniformly controlled cardioid polar pattern, the ADX10 helps to isolate the area or section being miked from other vocals or instruments on stage. The ADX10 has a smooth, accurate frequency range of 50 Hz - 18 kHz. This mic is lightweight, low profile and has a natural sound with exceptional sound response.
Primarily for use with the Audix RAD360 Wireless System, the ADX10 includes a tie-clip and a 3' attached cable terminating to a mini-XLRf connector.
MODEL VARIATIONS:
ADX10P - For hard wired application. Includes an 8' cable terminating to a mini-XLRf connector tie clip, external windscreen and a phantom power adapter module. 9 - 48 V phantom power required.
Type | Pre-polarized Condenser | Polar Pattern | Cardioid | Frequency Response | 50Hz - 18kHz | Impedance | 250 Ohms | Sensitivity | 5 mV/Pa @1k |
|
The smartLav+ is a broadcast-grade wearable microphone designed for use in a wide range of film, television and broadcast scenarios, or wherever broadcast quality audio is required in a discreet, portable format without the complication and expense of additional wireless equipment.
With the smartLav+ the user simply mounts the microphone on the talent, connects it to a smartphone or tablet headset jack and records via the RØDE Rec app for iOS, or any other audio app of their choice.
By employing a professional quality omni-directional condenser capsule the smartLav+ picks up sound equally from all around the microphone, allowing for versatility when mounting and ensuring a high degree of user-friendly operation.
A foam pop shield is supplied to minimise wind noise and vocal plosives (hard ʽbʼ, ʽtʼ and ʽpʼ sounds), as well as a durable mounting clip with in-built cable management. Its Kevlar® reinforced cable ensures that you never stretch or snap your microphone under normal usage conditions.
The smartLav+ is compatible with any audio app that accepts input from the headset connection, however it has been designed to pair perfectly with RØDEʼs RØDE Rec app for Apple iOS devices. RØDE Rec turns the userʼs iOS device into a fully-featured field recorder, with a wide range of equalisation presets to suit various recording situations, in addition to professional editing functions and the ability to publish to SoundCloud and Dropbox direct from the app.
Acoustic Principle Pressure Gradient
Active Electronics JFET
Capsule 0.10“
Polar Pattern [Omnidirectional - picks up all sides equally]
Address Type End
Frequency Range 20Hz - 20kHz (selected HPF @ 0)
Output Impedance 0Ω
Maximum SPL 110dB SPL (@ 1kHz, 1% THD into 1KΩ load)
Maximum Output Level 189.0dBu (@ 1kHz, 1% THD into 1KΩ load)
Sensitivity -35.0dB re 1 Volt/Pascal (17.80mV @ 94 dB SPL) +/- 2 dB @ 1kHz
Equivalent Noise Level (A-weighted) 27dB-A
Weight 6.00gm
Dimensions 1180.00mmH x 4.50mmW x 4.50mmD
Dimensions 1180.00mmH x 4.50mmW x 4.50mmD
Output TRRS Output
Warranty 1 year
|
Reviews
There are no reviews yet.