| Content | D&R's newest Telephone Hybrid-1 is an interface between a standard telephone line and a mixing console. Its purpose is to enable to record or broadcast a conversation between a caller and a presenter in an easy way.
Superb audio separation between in and outgoing signals are achieved by carefully designed internal circuitry. It is a problem solver for changing two wire communication into a four wire system with separate in and outputs.
Telephone hybrids provide the interface between professional audio equipment and the public telephone network.
They provide protection for your equipment and the public telephone lines, allowing for varying line signals and line conditions. Automatically canceling out the unwanted signal they also facilitate two-way communication down a single telephone line.
Each hybrid has a telephone line connection, a handset connection and separate connectors for audio input and output from a broadcast mixer, or other professional audio source.
A large proportion of D&R hybrids are used in radio and television broadcasting applications allowing external callers to be connected to the studio mixing console. Most of the other units are supplied to communication operations allowing extremely effective conversion between 4-wire audio circuits and standard telephone lines.
Specification
Output: balanced mic level -20dB. Input: Line level 0 dBu balanced. R/C balance: fully adjustable separation to more than 30dB.
C-BALANCE :12 pole rotary switch to select the optimum side tone attenuation.
R-BALANCE: Internal potentiometer to adjust for optimum side tone attenuation.
TO CALLER: Switch to temporarily connect the line (wall) connector to the Phone connector (appliance) to be able to dial and make a connection.
ON-LINE CONNECT: Line connect switch to connect and disconnect calls from the telephone line |
Shure DP11EQE Dynamics Processor Specification:
GENERAL:
Frequency Response: 20 to 20k Hz +/- 1.0 dB re 1 kHz
Dynamic Range: 104 dB minimum, A-weighted, 20 Hz to 20 kHz
Sampling Rate: 48 kHz
Digital-to-Analog, Analog-to-Digital Conversion: 20 bit resolution
Voltage Gain:
1 dB +/- 1dB (power off)
12 dB +/- 2 dB (input 10 dBV, output +4 dBu)
12 dB +/- 2 dB (input +4 dBu, output 10 dBv)
0 dB +/- 2 dB (equal input and output sensitivities)
Impedance:
Input: 47 kilohms +/- 20% actual
Output: 120 ohms +/- 20% actual
Input Clipping Level
+18 dBu minimum (at +4 dBu setting)
+6 dBV minimum (at 10 dBV setting)
Output Clipping Level
+18 dBu minimum (at +4 dBu setting)
+6 dBV minimum (at 10 dBV setting)
Total Harmonic Distortion
LED Signal Indicators
Signal: 40 dB
Clip: 6 dB down from input clipping
Propagation Delay from Input to Ouput
0.8 ms (all filters flat, no dynamics processing, 0 ms delay), up to 2.1 ms (all processing enabled)
Polarity
Input to output: inverting optional (default: non-inverting)
XLR: pin 2 positive with respect to pin 3
1/4-inch TRS: tip positive with respect to ring
Operating Voltage
DP11EQ: 120 Vac, 50/60 Hz, 50 mA max
DP11EQE: 230 Vac, 50/60 Hz, 25 mA max
DP11EQJ: 100 Vac, 50/60 Hz, 50 mA max
Temperature Range
Operating: 0 degrees to 60 degrees C (32 degrees to 140 degrees F)
Fuse
DP11EQ: 120 Vac. Fuse: 100 mA, 250V time delay
DP11EQE: 230 Vac. Fuse: 50 mA, 250 V time delay
DP11EQJ: 100 Vac. Fuse: 100 mA, 250 V time delay
Dimensions
219 mm x 137 mm x 44 mm (8-5/8 in x 5-3/8 in x 1-3/4 in)
Weight: 930 g (2.05 lbs)
DYNAMICS PROCESSOR
Gate and Expander:
Threshold: 72 to 1 dB, 0.5 dB resolution
Attack: 1.0 to 200 ms
Decay: 0.05 to 1 second
Gate Hold Time: 0 to 0.5 seconds
AGC Leveler
Threshold: 72 to 1 dB, 0.5 dB resolution
Attack: 0.2 to 3 seconds
Decay: 0.5 to 5 seconds
Hinge: Threshold to 1 dB, 0.5 dB resolution
Compressor and Limiter
Threshold: 72 to 1 dB, 0.5 dB resolution
Attack: 1.0 to 200 ms
Decay: 0.05 to 1 second
Knee: Hard or Soft selectable
No Overshoot Peak Limiter
Propagation delay: 1 ms
Threshold: 72 to 1 dB, 0.5 dB resolution
Attack: 0 msDecay: 100 ms
PARAMETRIC EQUALIZER
Parametric Filter Frequency Bands
Up to 9 bands, variable frequency, variable Q
Boost/Cut Range
+6 dB to 18 dB per band
Q Range
1/40-octave to 2 octave
High and Low Shelf/Cut Filters
Shelf, +6 to 18 dB per filter
Cut, 12 dB per octave nominal
DELAY
Up to 1.3 seconds, 21 microsecond resolution
|
GENERAL DATA
Power Supply 220 / 110V 25 VA
Dimension 434x351x44mm (1 rack unit)
Weight » 4 Kg
MEETING INTERFACE IN / OUT
Connector DB 9 female
Nominal in / out audio level 0 dBm
Input impedance 600 W / 10 KW (selectable)
Output impedance 100 W
* nominal line level: - 6 dBm
** it can vary depending on characteristics of telephone line
All measurements are intended at 1 kHz.
AUDIO PROGRAM IN / OUT
Connectors XLR, electr. balanced
Input impedance 600 W / 10K W (selectable)
Output level * - ¥ ¸ + 16 dBm
Output impedance 100 W
Noise on Receive output
2-Wire separation £ 25 dB**
4-Wire separation £ 70 dB
2-WIRE SECTION
Connector RJ11
Nominal input level - 6 dBm
Nominal output level - 6 dBm
Compensation mode Electronic, transf. decoupled
Impedance 600 W
4-WIRE SECTION
Connector Terminal block
Impedance 600 W
Nominal TX level 0 dBm
Nominal RX level 0 dBm
|
Description
The alphaton Feedback-Controller FC-100 is a revolutionary product for every microphone
application including wireless types. It can provide effective feedback control to any sound
reinforcement situation. It can also eliminated string feedback in guitars and bass instruments
which are equipped with piezo or condenser pickups.
The FC-100 provides 6 to 10 dB of feedback protection by analysing the incoming signal,
detecting the presence of feedback and then notching out the feedback frequency.
The FC-100 relieves the sound engineer automatically. It works dynamically and eliminates a
feedback signal before it can grow into a peak. Internally a discriminator circuit detects the
presence of regenerative feedback and triggers the automatic equaliser to insert a notch where
the feedback peak is coming up. This normally prevents other peaks from developing but if they
do, the process is repeated at high speed, thus keeping feedback under control.
Technical Data
In- and Outputs transformer balanced
max. Inputlevel + 3 dB
Gain (RS=200 Ohm, RL=2kOhm) 0 dB
Frequency Response 20 Hz ... 20 kHz, +/- 1,5 dB
Feeback Cancellation 6 ... 10 dB
Power Requirement 30 ... 48 V Phantom
Current drain ca. 8 mA
External Power Supply 9 ... 20 V DC, 3,5 mm jack, tip +
Housing Aluminium Diecast
Weight 285 grams
Dimensions 112 x 60 x 32 mm |
Interactive Reference-Class 2-Channel Expander/Gate/Compressor/ Peak Limiter with
Integrated De-Esser, Dynamic Enhancer, Tube Simulation and Low Contour Filter
Whether you?re recording, mixing or mastering, the COMPOSER PRO-XL MDX2600
gives you total dynamic control. It includes all of the features you would expect from
a reference class compressor?plus a voice-adaptive de-esser, a new dynamic
enhancer, authentic tube emulation and much more. These are some of the indispensable
tools for producing clean, consistent audio with virtually no loss in signal quality.
Features:
Switchable IKA (Interactive Knee Adaptation) program-adaptive compression circuitry
combines the advantages of hard-knee and soft-knee characteristics
Integrated de-esser with switchable male/female voice recognition removes excessive
sibilance from your vocal tracks
IGC (Interactive Gain Control) peak limiting circuitry combines clipper and program
limiter for reliable and inaudible protection against signal peaks
Switchable dynamic enhancer for brilliant, lively audio even with heavy compression
IRC (Interactive Ratio Control) expander/gate circuitry for virtually inaudible
noise suppression
Switchable tube simulation for the extra warmth and transparency of classic
tube circuitry
Automatically or manually adjustable attack and release times
Switchable low contour filter prevents "pumping" due to low-frequency
dominated compression
Stereo couple function with independent output level settings
Switchable side chain input with side chain monitor function
Ultra low-noise 4580 operational amplifiers and state-of-the-art THAT¬ VCA's
Separate 12-segment LED meters for input/output levels and gain reduction
Dedicated "traffic light" threshold and de-esser level displays
High-quality detented ALPS¬ potentiometers and illuminated switches
Servo-balanced inputs and outputs with ? in. TRS and gold-plated XLR
connectors
Relay-controlled hard bypass switch with auto bypass function in case
of power failure
Manufactured under ISO9000 certified management system
|
The Multicom Pro-XL MDX4600 gives you 4 channels of first-class dynamic
control in a single rack space. With a multitude of new features like the
advanced program-adaptive expander gate, extensive metering plus a variety
of configuration options, the Multicom Pro-XL puts a lot of dynamic processing
power in your rack.
Features
Switchable IKA (Interactive Knee Adaptation) program-adaptive compression
circuitry combines the advantages of hard-knee and soft-knee characteristics
IRC (Interactive Ratio Control) expander/gate circuitry for virtually inaudible noise
suppression
Switchable dynamic enhancer for brilliant, lively audio even with heavy compression
IGC (Interactive Gain Control) peak limiting circuitry combines clipper and program
limiter for reliable and inaudible protection against signal peaks
Switchable low contour filter prevents "pumping" due to low-frequency dominated
compression
Stereo couple function selectable for channels 1/2 and 3/4
Ultra low-noise 4580 operational amplifiers and state-of-the-art THAT¬ VCA's
Separate 8-segment LED meters for input/output levels and gain reduction
Selectable operating level (+4 dBu/-10 dBV)
High-quality detented ALPS¬ potentiometers and illuminated switches
Servo-balanced inputs and outputs with ? in. TRS and gold-plated XLR
connectors
Manufactured under ISO9000 certified management system
|
Reviews
There are no reviews yet.