Content |
Power Output Level: QD4480
8ohm (Quad Ch) 80W
4ohm (Quad Ch) 120W
8ohm bridged mono 240W
Input Sensitivity (8ohm, 1kHz) 0.775Vrms
Input Impedance 20kohm Balanced
Slew Rate (8ohm, Full Swing) ±30V/?sec
Frequency Response (±0.5dB) 20kHz ~ 50kHz
T.H.D. (f=20Hz~20kHz, Half Power) 0.03%
Signal to Noise Ratio 105dB
Damping Factor (8ohm, 1kHz) 100
Rasidual Noise -85dB
Channel Separation (8ohm, 1kHz) 80dB
Voltage Gain (4ohm) 26dB 29dB 32dB
Power Source 100-120VAC or 220-240VAC ; 50/60Hz
(supplied AC mains transformer depends on country requirements)
Power Consumption 300W 420W 770W
Weight 11.5kg/25.3lb 15.5kg/34.2lb 17kg/37.5lb
Dimensions 482(W) x 88(H) x 369(D) mm
/19(W) x 3.5(H) x 14.5(D) in
| - 6CH 60W DIGITAL AMPLIFIER
- LIGHT WEIGHT
- 6 BUS BROADCASTING FUNCTION WITH A UTP (CATEGORY 5) CABLE.
- VOLUME AND 5 BAND EQ TUNING FUNCTION BY CHANNEL
- AMP ID AUTO/MANUAL ALLOCATION FUNCTION
- SELF-BROADCASTING FUNCTION USING A LOCAL INPUT
- INTERFACE FUNCTION WITH OTHER EQUIPMENT USING A CONTROL INPUT/OUTPUT CONTACT
- Manufacturer: INTER-M
- Category: AMPLIFIERS
- Use: POWER AMPLIFIERS 100V
- Measurement Unit: Attribute34381
- Warranty Months: 12
- Depth (cm): 38.0
- AC Line Voltage and Frequency Configurations Available: 220-240VAC DC24V
- Height (cm): 8.8
- Weight (Kg): 13.0
- Order Quantity: 1
- Power Output: 60
- Rack Installation Possible: Yes
- Channels: 6
- Power Output W/4Ω: 60
- Frequency Response (at 1W, 4/8Ω) (dB) ±: 80Hz-20KHz
- Catalog: Professional
- Amplifier Type: Power Amplifier
- Load Impedance: Ohm
- Group: Attribute49042, Attribute50583
- Width (cm): 48.2
|
Power Output Level: QD4240
8ohm (Quad Ch) 40W
4ohm (Quad Ch) 60W
8ohm bridged mono 120W
Input Sensitivity (8ohm, 1kHz) 0.775Vrms
Input Impedance 20kohm Balanced
Slew Rate (8ohm, Full Swing) ±30V/?sec
Frequency Response (±0.5dB) 20kHz ~ 50kHz
T.H.D. (f=20Hz~20kHz, Half Power) 0.03%
Signal to Noise Ratio 105dB
Damping Factor (8ohm, 1kHz) 100
Rasidual Noise -85dB
Channel Separation (8ohm, 1kHz) 80dB
Voltage Gain (4ohm) 26dB 29dB 32dB
Power Source 100-120VAC or 220-240VAC ; 50/60Hz
(supplied AC mains transformer depends on country requirements)
Power Consumption 300W 420W 770W
Weight 11.5kg/25.3lb 15.5kg/34.2lb 17kg/37.5lb
Dimensions 482(W) x 88(H) x 369(D) mm
/19(W) x 3.5(H) x 14.5(D) in
|
Model CT475
Product Type Amplifier
Channels 4
Sensitivity 1.4V
Rated Power Output 75W per Channel into 8 ohms
Signal to Noise Ratio (below rated power 20Hz to 20kHz, A-Weighted 110dB
Total Harmonic Distortion (THD) (full rated power, 20Hz - 20kHz)
Intermodular Distortion (from 0dB down to -40dB)
Frequency Response (at 1W into 4/8 ohms) ± 0.5dB
Crosstalk (below rated power 20Hz to 1kHz) > 70dB
Common Mode Rejection (20Hz to 1kHz) > 55dB, typically > 70dB
Dimension (H x W x D) 1.75" x 19" x 14.25“
Weight 10 lbs (4.5 kg)
| The S Series of RAM Audio amplifiers distils all these features to fulfill all your needs, whether youʼre starting a P.A. amplifier project from scratch, or you need to upgrade your present sound reinforcement equipment. In the S Series amps, you'll find five 2-channel models and five 4-channel models, all offering plentiful power levels at low distortion in the range of 1.5 to 6 kilowatts, yet weighing in around 8 kilos and 30 cm deep. • Ultra-compact and lightweight 2-U high • Laser cut aluminum front panels with integrated carrying handles • Neutrik® XLR input connectors, input and signal link in 2 channel models • Input Link switch: allow daisy-chaining of the input signal • Neutrik® Speakon® output connectors • Detented sealed potentiometers for easy recall of volume settings • ICL™, PMS™, Hi-temp, Signal indicators per channel • Power on and Stand-by leds • Highly versatile with multiple configuration and additional module options • Full PC control via EtheRAM (with EtheRAM Control module) • Switchable ICL™ clip-limiters per channel • Switchable (30-50 Hz) sub-sonic highpass filter per channel • Three-position gain selector (26, 32 or 38 dB) • Dual or bridge mode selector • Twin temperature controlled, back to front cooling fans • Oversized power components (high SOA reserve specification) Standard Signal Inputs Module: The S Series amps are equipped as standard with twin Neutrik® XLR, doubled by two other XLR connectors for linking purposes. In the 4 Channel models an XLR input per channel is provided with the signal linking facility. Analog Processor Module: permits a very easy, user-friendly signal processing to enable the amp to set up a bi-amp system without any other outboard device. These are the Processor's main characteristics: • 2-way stereo crossover (dual mono or single bridged sub output) • 24dB/oct Linkwitz-Riley configurable crossover (90, 100 o 120Hz) • Adjustable attenuation in the High-pass outputs (-3, -6 or -9dB) • Adjustable Limiter, relative to Max. Output (-3, -6 or -9dB) DSP44_S Module: Digital Signal Processor fully programmable through an USB port. These are the Processor's main characteristics: • 4 Inputs/4 Outputs or 2 In/2 Out free route configurable. • 24 bits/192 kHz 256x Oversampling Converters. • Output Delay: 0 to 7.1 meters (20.69ms) per channel. • XOver: Up to 48dB/oct Butterworth, Linkwitz-Riley and Bessel. • EQ: 9 filters per channel (Parametric, Shelving, LP,HP,BP,SB). • Gain, Mute and Phase inversion per channel. • RMS Power and Peak Voltage output limiter per channel. • Real Time operation from USB or front panel configuration. Standard Signal Inputs Module EtheRAM Control Module Ethernet Audio Transport (Coming soon) Analog Processor Module DSP44_S Module EtheRAM Control Module AES/EBU Digital Input (Coming soon)
OUTPUT POWER |
S-1500 |
S-2000 |
S-3000 |
S-4000 |
S-6000 |
S-3004 |
S-4004 |
S-4044 |
S-6004 |
S-6044 |
1kHz, 1.0% THD |
2 ohms |
2x880W |
2x1190W |
2x1570W |
2x1950W |
2x2950W |
4x700W |
4x980W |
- |
4x1440W |
- |
4 ohms |
2x575W |
2x790W |
2x1100W |
2x1380W |
2x2025W |
4x500W |
4x670W |
4x975W |
4x1000W |
4x1480W |
8 ohms |
2x325W |
2x460W |
2x630W |
2x810W |
2x1250W |
4x300W |
4x430W |
4x690W |
4x620W |
4x1015W |
Bridge @ 4ohms |
1760W |
2380W |
3140W |
3900W |
5900W |
2x1400W |
2x1960W |
- |
2x2880W |
- |
Bridge @ 8ohms |
1150W |
1580W |
2200W |
2760W |
4050W |
2x1000W |
2x1340W |
2x1950W |
2x2000W |
2x2960W |
P. N. 12dB C.F. |
2 ohms |
2x975W |
2x1360W |
2x2060W |
2x2460W |
2x4225W |
4x890W |
4x1170W |
- |
4x2080W |
- |
4 ohms |
2x610W |
2x880W |
2x1240W |
2x1600W |
2x2600W |
4x580W |
4x820W |
4x1230W |
4x1280W |
4x2110W |
Frequency Response (power bandwidth ±0.25dB): 20Hz-20kHz Phase Response (@1W 20Hz-20kHz): ±15deg Total Harmonic Distortion (20Hz-20kHz): Intermodulation Distortion (SMPTE): Crosstalk (20Hz-20kHz): >75dB Voltage Gain (selectable): 26/32/38 dB Sensitivity: 1500:2.6/1.3/0.6V 2000:3.0/1.5/0.8V 3000:3.6/1.8/0.9V 4000:4.0/2.0/1.0V 6000:5.0/2.5/1.3V 3004:2.6/1.3/0.6V 4004:3.0/1.5/0.8V 4044:3.7/1.9/0.9V 6004:3.5/1.8/0.9V 6044:5.0/2.5/1.3V Signal to noise ratio: 1500:112dB 2000:113dB 3000:115dB 4000:116dB 6000:118dB 3004:112dB 4004:113dB 4044:116dB 6004:116dB 6044:118dB Required AC Mains (@4ohms 1/8 r.p.): 1500:4A 2000:4.8A 3000:6.2A 4000:7.5A 6000:10.5A 3004:6A 4004:7.5A 4044:11A 6004:10.5A 6044:15A Dimensions (WxHxD): 483x88.9x310 mm - 19x3.5x12.2 inches Weight (Net): 1500/2000: 8Kg - 17.6Lbs 3000/4000/3004/4004/4044: 8.5Kg-18.7Lbs 6000/6004/6044: 8.6Kg-18.9Lbs Protections: Soft-start, Turn-on Turn-off transients, Muting at turn-on, Over-heating, DC, RF, Short-circuit, Open or mismatched loads, Overloaded power supply,ICL™, PMS™, SSP™ |
The S Series of RAM Audio amplifiers distils all these features to fulfill all your needs, whether youʼre starting a P.A. amplifier project from scratch, or you need to upgrade your present sound reinforcement equipment.
In the S Series amps, you'll find five 2-channel models and five 4-channel models, all offering plentiful power levels at low distortion in the range of 1.5 to 6 kilowatts, yet weighing in around 8 kilos and 30 cm deep.
• Ultra-compact and lightweight 2-U high
• Laser cut aluminum front panels with integrated carrying handles
• Neutrik® XLR input connectors, input and signal link in 2 channel models
• Input Link switch: allow daisy-chaining of the input signal
• Neutrik® Speakon® output connectors
• Detented sealed potentiometers for easy recall of volume settings
• ICL™, PMS™, Hi-temp, Signal indicators per channel
• Power on and Stand-by leds
• Highly versatile with multiple configuration and additional module options
• Full PC control via EtheRAM (with EtheRAM Control module)
• Switchable ICL™ clip-limiters per channel
• Switchable (30-50 Hz) sub-sonic highpass filter per channel
• Three-position gain selector (26, 32 or 38 dB)
• Dual or bridge mode selector
• Twin temperature controlled, back to front cooling fans
• Oversized power components (high SOA reserve specification)
Standard Signal Inputs Module: The S Series amps are equipped as standard with twin Neutrik® XLR, doubled by two other XLR connectors for linking purposes. In the 4 Channel models an XLR input per channel is provided with the signal linking facility.
Analog Processor Module: permits a very easy, user-friendly signal processing to enable the amp to set up a bi-amp system without any other outboard device. These are the Processor's main characteristics:
• 2-way stereo crossover (dual mono or single bridged sub output)
• 24dB/oct Linkwitz-Riley configurable crossover (90, 100 o 120Hz)
• Adjustable attenuation in the High-pass outputs (-3, -6 or -9dB)
• Adjustable Limiter, relative to Max. Output (-3, -6 or -9dB)
DSP44_S Module: Digital Signal Processor fully programmable through an USB port. These are the Processor's main characteristics:
• 4 Inputs/4 Outputs or 2 In/2 Out free route configurable.
• 24 bits/192 kHz 256x Oversampling Converters.
• Output Delay: 0 to 7.1 meters (20.69ms) per channel.
• XOver: Up to 48dB/oct Butterworth, Linkwitz-Riley and Bessel.
• EQ: 9 filters per channel (Parametric, Shelving, LP,HP,BP,SB).
• Gain, Mute and Phase inversion per channel.
• RMS Power and Peak Voltage output limiter per channel.
• Real Time operation from USB or front panel configuration.
Standard Signal Inputs Module
EtheRAM Control Module
Ethernet Audio Transport (Coming soon)
Analog Processor Module
DSP44_S Module
EtheRAM Control Module
AES/EBU Digital Input (Coming soon)
|
OUTPUT POWER |
S-1500 |
S-2000 |
S-3000 |
S-4000 |
S-6000 |
S-3004 |
S-4004 |
S-4044 |
S-6004 |
S-6044 |
1kHz, 1.0% THD |
|
|
|
|
|
|
|
|
|
|
2 ohms |
2x880W |
2x1190W |
2x1570W |
2x1950W |
2x2950W |
4x700W |
4x980W |
- |
4x1440W |
- |
4 ohms |
2x575W |
2x790W |
2x1100W |
2x1380W |
2x2025W |
4x500W |
4x670W |
4x975W |
4x1000W |
4x1480W |
8 ohms |
2x325W |
2x460W |
2x630W |
2x810W |
2x1250W |
4x300W |
4x430W |
4x690W |
4x620W |
4x1015W |
Bridge @ 4ohms |
1760W |
2380W |
3140W |
3900W |
5900W |
2x1400W |
2x1960W |
- |
2x2880W |
- |
Bridge @ 8ohms |
1150W |
1580W |
2200W |
2760W |
4050W |
2x1000W |
2x1340W |
2x1950W |
2x2000W |
2x2960W |
P. N. 12dB C.F. |
|
|
|
|
|
|
|
|
|
|
2 ohms |
2x975W |
2x1360W |
2x2060W |
2x2460W |
2x4225W |
4x890W |
4x1170W |
- |
4x2080W |
- |
4 ohms |
2x610W |
2x880W |
2x1240W |
2x1600W |
2x2600W |
4x580W |
4x820W |
4x1230W |
4x1280W |
4x2110W |
Frequency Response (power bandwidth ±0.25dB): 20Hz-20kHz
Phase Response (@1W 20Hz-20kHz): ±15deg
Total Harmonic Distortion (20Hz-20kHz): Intermodulation Distortion (SMPTE): Crosstalk (20Hz-20kHz): >75dB
Voltage Gain (selectable): 26/32/38 dB
Sensitivity: 1500:2.6/1.3/0.6V 2000:3.0/1.5/0.8V 3000:3.6/1.8/0.9V 4000:4.0/2.0/1.0V 6000:5.0/2.5/1.3V
3004:2.6/1.3/0.6V 4004:3.0/1.5/0.8V 4044:3.7/1.9/0.9V 6004:3.5/1.8/0.9V 6044:5.0/2.5/1.3V
Signal to noise ratio: 1500:112dB 2000:113dB 3000:115dB 4000:116dB 6000:118dB
3004:112dB 4004:113dB 4044:116dB 6004:116dB 6044:118dB
Required AC Mains (@4ohms 1/8 r.p.): 1500:4A 2000:4.8A 3000:6.2A 4000:7.5A 6000:10.5A
3004:6A 4004:7.5A 4044:11A 6004:10.5A 6044:15A
Dimensions (WxHxD): 483x88.9x310 mm - 19x3.5x12.2 inches
Weight (Net): 1500/2000: 8Kg - 17.6Lbs 3000/4000/3004/4004/4044: 8.5Kg-18.7Lbs 6000/6004/6044: 8.6Kg-18.9Lbs
Protections: Soft-start, Turn-on Turn-off transients, Muting at turn-on, Over-heating, DC, RF, Short-circuit, Open or mismatched loads, Overloaded power supply,ICL™, PMS™, SSP™ |
Reviews
There are no reviews yet.