Content |
The new J series is a technologically advanced range of products that improves on the performance of the previous Jolly line. The new J series is a competitive, value for money range of speakers. The range is based on the development of three new high efficiency class-D amplifiers with power specifications of 350 + 100W for the J 15A & J 12A, 200 + 50W for the J 8A and 80 + 40W for the J 5A.
These amplifiers have been designed 'from the ground up' in FBT’s R&D laboratories. The largest amplifier model that equips the J 15A and J 12A has a switch mode power supply as well as a digital signal processor with 4 pre-sets.
The J 8A and J 5A amplifiers have toroidal transformer power supplies. The J 8A has a digital signal processor with 2 pre-sets, whilst the J 5A has analog signal processing.
The speakers have been completely redesigned, introducing the technological developments of recent years to achieve a far superior efficiency and linearity.
Following from the new J series, FBT bring you the DJ 15A, designed with today’s modern DJ in mind. The DJ 15A has invaluable features allowing quality audio playback using our revolutionary DSP technology. This includes 4 presets enabling the DJ to change the sound of their music to suit the environment they play within.
These DSP presets will allow the DJs audience to enjoy improved sound quality and SPL, especially in bass reproduction at high volume.
The DJ 15A also has another useful feature for DJs, including a two channel input mixer allowing the DJ to plug a music source and microphone direct into the speaker, giving separate control over volume for both devices. You can also daisy chain these speaker together if required. Ideal for many application of today’s modern DJ.
Code: |
37687 / 37905 White |
Configuration: |
2 way |
Built-in amplifier LF/HF: |
80/40 W RMS |
Built-in amplifier peak LF/HF: |
160/80 W |
Frequency response: |
80Hz - 20KHz -6dB |
Low Frequency woofer: |
5 - 1 coil inch |
High Frequency driver: |
1 dome - 0.75 coil inch |
Maximum SPL cont/peak: |
113 / 117 dB |
Dispersion: |
90° x 90° HxV |
Input impedance: |
22 Kohm |
Crossover Frequency: |
3.5 KHz |
AC Power requirements: |
75 VA |
Input connector: |
XLR combo with loop |
Power cord: |
5 / 16.4 m/ft |
Net Dimension (WxHxD): |
170x275x180 - 6.69x10.82x7.08 mm/inch |
Net Weight: |
3.4 / 7.49 Kg/lb |
Transport Dimension (WxHxD): |
240x345x235 - 9.44x13.58x9.25 mm/inch |
Transport Weight: |
4.2 / 9.25 Kg/lb |
| LD Systems MIX 6 A G3 Active 2-Way Loudspeaker with Integrated 4-Channel Mixer
The ideal choice for small-scale PA and personal monitoring applications, the active LD MIX 6 A G3 integrates a 4-channel mixer and Class D amplification with 2 x 280 watts peak power. The compact bass reflex loudspeaker features a 6.5" custom woofer and 1" HF driver complement, 80 Hz to 20 kHz frequency response and 80° x 70° dispersion delivering crystal clear sound with punch and detail.
Accomodating a wide variety of input sources including electric instruments, smartphones, tablets, MP3 and CD players, the built-in mixer provides 3 microphone channels and a stereo line channel with 2-band EQ each plus switchable hi-Z input and 15 V phantom power. The output section includes a 3-band master EQ for overall tone shaping, 4-segment LED metering, an adjustable monitor and RCA recording outputs. In addition, the LD MIX 62 A G3 sports a DSP with 16 effect presets, limiter and overcurrent, overload, short circuit and thermal protection. A 4 ohm slave output allows powering the passive LD MIX 6 G3 for a dual speaker setup.
The rigid MDF enclosure features two 16 mm pole mounts for horizontal or vertical orientation. On its own or in tandem with the passive unit, the LD MIX 62 A G3 provides amazing performance and versatility in a lightweight, easily portable package.
Product type
PA loudspeaker
Tweeter dimensions (mm)
25.4 mm
Tweeter brand
Custom-made
Dispersion (H x V)
80 x 70 °
Frequency response
80 - 20.000 Hz
Amplifier output (RMS)
2x70 W
Amplifier output (peak)
2x280 W
Protection circuits
ICL (Intelligent Clip Limiting), over-current, overload, short circuit, thermal overload
MIXER
Mic inputs
6.3 mm jack, XLR
Controls for Mic Inputs
DFX Send, EQ Hi, EQ Low, Hi-Z Switch (channel 1 only), level
Input Impedance Mic Inputs
14 kOhm
Input Sensitivity Mic Input
70 mV
Line input connectors
2 x RCA
Controls Line Inputs
DFX Send, EQ Hi, EQ Low, level
Input Impedance Line Inputs
4.4 kOhm
Input Sensitivity Line Inputs
- 5 dBu
Hi-Z input connectors
6.3 mm jack
Input Impedance Hi-Z Input Connectors
100 kOhm
Connector Type Monitor Line Output
2 x RCA
Controls for Monitor Line Output
Monitor Volume
Max Output Level Line Output Monitor
28 dBu
Connector Type Record Output
2 x RCA
Increased power main output (at 4 ohm)
70 W
DSP Digital Effect
DSP Number of Programs
16
DSP Controls
DFX Return, Mute switch
DSP Display Elements
Peak LED
Main Section
Main section controls
EQ Hi, EQ Low, EQ Mid, Master Volume, Phantom Power, voltage selector switch
Main section indicators
4-segment Level Meter, power LED
Mains connector
IEC socket
Operating voltage
transformer
Operating voltage
110 - 120 V ~ 50/60 Hz or 220 - 240 V ~ 50/60 Hz, switchable
Cabinet
Cabinet construction
Bass Reflex
Cabinet surface
texture paint
Other features
2 x 16 mm pole mount socket, rubber feet
|
Features
400 Watt digital bi-amplification
126 dB max spl
Wide dispersion 90 x 70 constant directivity horn
8" High power neodymium woofer, 2.5" voice coil
1" Mylar dome, neodymium high frequency driver
DSP processing, boost eq, soft limiter and protection
Xlr/jack input, xlr signal output
Acoustical Specifications
Frequency Response -3 dB: 65 Hz ÷ 20 kHz
Max SPL: 126 dB
Horizontal coverage angle: 90°
Vertical coverage angle: 70°
Compression Driver: 1" neo, 1.4" voice coil
Woofer: 8" neo, 2.5" voice coil
Input/Output Section
Input signal: bal/unbal
Input connectors: xlr - Jack
Output connectors: xlr
Processor Section
Crossover frequencies: 1800 Hz
Limiter: Fast limiter, RMS limiter
Controls: Flat, Boost
Amplifier Specifications
Total power: 400 W
High frequencies: 100 W
Low frequencies: 300 W
Connections: VDE
Cabinet
Cabinet Material: Composite PP
Hardware: 2 x M10 flying points
Handles: 1 on top
Pole Mount/Cap: Yes
Grille: Steel
Colour: Anthracite grey
Physical Specifications
Height: 480/18.9 mm/inch
Width: 291/11.45 mm/inch
Depth: 274/10.7 mm/inch
Net Weight: 9.2/20.28 kg/lbs
|
The very compact 4030B is a powerful bi-amplified speaker system ideal for small to mid-sized commercial installations such as clubs, bars, board rooms, museums, theaters, etc.
Our Intelligent Signal Sensing (ISS) feature, reduces power consumption to less than 0.5 watts by automatically switching the active monitor to standby, when no audio signal has been detected for some time. When it receives an audio signal again, the loudspeaker turns back on.
ISS is fully compliant with the latest EU requirements and the ErP 2013 Directive for electronic devices.
The MDETM (Minimum Diffraction EnclosureTM) enclosure has rounded edges and a gently curved front and sides to achieve a very smooth frequency response and superb imaging qualities with minimized cabinet edge diffraction.
The 4030B also features the advanced Genelec Directivity Control WaveguideTM (DCWTM), a revolutionary flow-optimized reflex port design, optimized die-cast aluminium structure with extremely durable semi-matt finish and acoustically optimized metal grilles.
| 100 dB | | 58 Hz - 20 kHz (± 2.5 dB)
55 Hz - 20 kHz (-3 dB) | | 3.0 kHz | | Bass 5" + Treble 3/4“
metal dome + DCWTM | | Bass 40 W + Treble 40 W | | H x W x D 285 x 189 x 178 mm | | 5.5 Kg (12.1 lb) | | 1 x balanced Phoenix connector |
| |
Comprising four versatile loudspeaker enclosures for either portable use or fixed installation, FBT is debuting the VENTIS range at Pro Light + Sound 2016. Available in either passive or bi-amplified versions, each of the models – the VENTIS 115, 112, 110, and 206 – has been designed to meet the highest standards in both performance and aesthetic appeal.
For the VENTIS range, quality and flexibility are the watchwords. Based on a powerful combination of B&C compression drivers and FBT’s own custom, long excursion woofers, the 115, 112 and 110 models are two-way, bass reflex designs housed in 15mm birch plywood. A full-grille design backed by specially treated acoustic cloth delivers the characteristic style for which FBT is known, while fully rotatable constant directivity horns ensure accurate coverage.
The three enclosures are as suitable for fixed installation as they are for use on the stage. M10 points are included as standard while an optional U-bracket can be used for wall-mounting. For use on the road, the VENTIS models include aluminum handles with rubber inserts, a 35mm polemount socket, and a 45° sloped profile for unobtrusive placement on-stage as a monitor.
Meanwhile the multi-purpose VENTIS 206 can be deployed as a front fill, an under-balcony fill, as a main providing pristine speech intelligibility or simply as the full-range companion of a subwoofer. Constructed in 12mm birch plywood, the 206 has an integrated rear handle, an optional mounting bracket and, most importantly, an astonishing size to SPL ratio.
Power for the active VENTIS models comes courtesy of a specially designed, Italian made switching mode amplifier module. Low frequencies are driven by a highly efficient 700W RMS (full bridge) Class-D topology, operating with extremely low THD. For the HF stage, a 200W RMS performance is delivered via a meticulously crafted Class-H / AB design.
Finally, DSP on-board the VENTIS enclosures is both user friendly and powerful. Located on the rear of each enclosure, a menu-driven system is navigated via a single rotary control with push-to-select functionality. A total of 6 pre-optimised settings are available (see below), plus 2 further slots for users to form their own designs, using 5 parametric equalizers per slot. Also available is a high-pass filter, a mic/line selector, low, mid and high tone settings and an optional delay of between 0 and 3.5 metres. Finally, users can exclusively choose between two limiter modes, MAX-SPL or MAX-QUALITY, to best suit their performance.
- 2-way, bi-amplified, bass reflex design
- Biamped: 700W RMS LF and 200W RMS HF power amplifiers in Class D for LF and in Class H/AB for HF
- Digital Signal Processor with graphic display
- 15 mm (0.59”) birch plywood scratch resistant enclosure and internal bracing
- High efficiency switch mode power supply
- Control Panel features balanced XLR/Jack input, XLR LINK OUT, 2 x Volume, RCA Stereo input, DSP display with rotative encoder and push
- 2x165mm (6.5”) LF woofer with 38mm (1.5”) voice coil, custom made for FBT
- 25mm (1”) exit throat B&C HF compression driver with 36mm (1.4”) voice coil
- Frequency response from 70Hz to 20 kHz
- 70°H x 50°V Constant Directivity Rotatable Horn
- 6 x M10 suspension points, wall bracket mount thread, 35mm (1 3/8”) top-hat
- One integrated handle
- 12mm (0.47”) birch plywood scratch resistant enclosure and internal bracing
Code: |
40639 |
Configuration: |
2 way |
Built-in amplifier LF/HF: |
700/200 W RMS |
Built-in amplifier peak LF/HF: |
1400/400 W |
Frequency response: |
70Hz - 20KHz -6dB |
Low Frequency woofer: |
2x6.5 - 1.5 coil inch |
High Frequency driver: |
1 - 1.4 coil inch |
Maximum SPL cont/peak: |
124/131 dB |
Dispersion: |
70° x 50° rotatable HxV |
Input impedance: |
640 Kohm |
AC Power requirements: |
640 VA |
Input connector: |
XLR with loop, RCA ST |
Power cord: |
5/16.4 m/ft |
Net Dimension (WxHxD): |
190x560x260 / 7.48x22.04x10.23 mm/inch |
Net Weight: |
12.3/27.11 Kg/lb |
Transport Dimension (WxHxD): |
290x660x360 / 11.41x25.98x14.17 mm/inch |
Transport Weight: |
14.3/31.52 Kg/lb |
|
Reviews
There are no reviews yet.