Content |
STEREO MODE: 2 x 450W @ 8Ω. 2 x 750W @ 4Ω. 2 x 1000W @ 2Ω.
BRIDGE MODE: 1600W @ 8Ω. 2450W @ 4Ω.
PROTECTIONS: Soft start DC, short circuit, over load, clip limit, over heat,
progressive volume, VHF. Weight 9.7 kg.
Dimension W 483 x H 89 x D 450 mm.
Assembled in China. Engineered by Montarbo. |
Model T5n
Product Type Power Amplifier
Output Power (W) 1kHz THD+N=1% (120V)
2Ω per channel 2500
4Ω per channel 2200
8Ω per channel 1350
4Ω bridge 5000
8Ω bridge 4400
Output Power (W) 1kHz 20mS burst (120V)
2Ω per channel 3400
4Ω per channel 2200
8Ω per channel 1350
4Ω bridge 6800
8Ω bridge 4400
SN ratio (20Hz-20kHz) 107dB
THD+N 20Hz-20kHz, Half Power RL-4Ω, 8Ω
Intermodulation Distortion 60Hz: 7kHz, 4:1, Half Power 0.1%
Frequency response RL=8Ω,Po=1W,HPF=OFF 20Hz-20kHz (Max) 0dB
Frequency response RL=8Ω,Po=1W,HPF=OFF 20Hz-20kHz (TYP) 0dB
Frequency response RL=8Ω,Po=1W,HPF=OFF 20Hz-20kHz (MIN) 6dB
Channel Separation (Half Power RL=8Ω,1kHz Att. max input 600Ω shunt) 70dB
Residual Noise Att,min 20Hz-20kHz(DIN AUDIO) -70dBu
Damping factorRL=8Ω 1kHz 800
Voltage Gain Att.max 26dB
Maximum Input Voltage +24dBu
Input Impedence 20kΩ (balance) 10kΩ (unbalance)
Controls Specifications
Front Panel POWER switch(push on/push off) attenuator (31 position) x2
Rear Panel MODE switch (STEREO/BRIDGE/PARALLEL) X1; HPF switch (20Hz/OFF 12dB/oct) x1; AMP ID switch (6PDIP)x1
Connectors Specifications
Input XLR-3-31 type/ch; Euroblock connector (balance)/ch
Output SPEAKON/ch, 5way biding postx1
Date Port RJ45x2
Indicators Specifications
Power/Standby x1 (Green/Orange)
Remote x1 (Green)
Protection x1 (Red)
Temp x1 (Red) heatsink temp 85°C
Signal x2 (Green)
Mute x2 (Red)
Clip/Limit x2 (Red)
Load protection POWER switch on/off mute; DC-fault: power supply shutdown / do not return automatically
Cooling Variable-speed fan: x2
Power requirements 120V/60Hz
Weight 14.0 kg
Dimensions (W x H x D) 480 x 88 x 456mm (2U) |
Power supply
- Powersoft legendary universal switch-mode power supply up to 400VAC tolerant with Power Factor Correction
- Patented output filter with ripple cancellation network
- Low Inrush Limiting reduces AC inrush current, removing the need for expensive power sequencers
- Detachable AC mains cable with IEC C19/22.2 (16A for EU, 20 A for USA) socket
Protections
Fully protected circuit design with:
- Ac protection: shut down power supply when AC mains voltage is outside the operating range
- Clip limiter: prevents severely clipped waveforms from reaching loudspeakers, while still maintaining full peak power output
- DC protection: protects against infrasonic signal at the outputs
- VHF protections: protects the loudspeakers against non-audible, strong, non-musical high-frequency signals
- Short circuit protection: protects the amplifier from short circuit or other stressful events for the output circuits with automatic protection reset
- Long term limiter: protects the loudspeaker against steady long term RMS (non-audio) signals, by reducing maximum output
- Thermal protection: output stages operating temperature up to 80 °C (176 °F)
- Temperature controlled continuous variable speed fan, front to back airflow
- Temperature forecast with LCD traced historical behavior
General
- Fixed frequency switchmode output stage for high grade sound accuracy
- Compact size – all models only 1 RU for reduced rack cost and space
- Light weight – for easier racking and shipping: 7 kg (15.4 lbs)
- Standard Phoenix connectors: analog audio outputs, aux supply, alarms and GPIO
- Remotely switchable double input (main and aux) per channel
Loudspeaker system configuration
- Direct drive either low impedance loads or 70V / 100V Hi-Z distributed lines
- Switchable 35Hz / 70Hz high pass filter per channel
- Mixed configuration with Lo-Z/Hi-Z systems possible
- Bridged mode low impedance per channel pair
Alarms and GPI/O
- NC/NO contacts per channel for alarm notifications
- Remote ON/OFF switch
- Remote VCA control per channel
Digital Signal Processing
- TI C6000 DSP platform
- AD/DA converter: dual 24bit @ 48 kHz Tandem® architecture
- Input/output independent equalizers per channel providing PEQ, raised cosine, shelving IIR filters as well as custom output FIR filters
- Delay up to 100 ms for time alignment
- Active DampingControl™ for cable compensation
- Peak, RMS voltage, RMS current, TruePower™ limiters
Remote Control & Monitoring
Via software:
- Control and diagnostics monitoring via ArmoníaPlus
- Dedicated WebApp
Via Hardware:
- Attenuation (from 0dB to 26dB)
- High-pass filters (35Hz, 70Hz)
- Lo-Z/Hi-Z/70V/100V output selection
- Adjustable gain (from 26dB to 35 dB)
General |
Output power per Channel |
Output power per Channel |
1000 W @ 2 Ω |
800 W @ 4 Ω |
800 W @ 8 Ω |
Bridge mode |
|
2000 W @ 4 Ω |
1600 W @ 8 Ω |
Max output voltage / current |
Max unclipped output voltage@8 Ω |
|
|
115 Vpeak |
Current |
|
|
45 Apeak |
AC main power |
Power supply |
Universal, regulated switch mode with PFC (Power Factor Correction) |
Nominal power requirement |
|
|
100-240 V ±10%, 50-60 Hz |
Operating voltage |
|
|
90 V – 264 V |
Power consumption / current draw |
Idle |
|
115 V: 23 W – 0.34 A |
230 V: 23.3 W – 0.21 A |
1/8 of max output power @ 4 Ω |
|
115 V: 267 W – 2.5 A |
230 V: 274 W – 1.5 A |
THERMAL |
Operating temperature range |
|
|
0° – 45° C – 32° – 113° F |
Thermal dissipation* |
Idle |
|
115 V: 78 BTU/h |
230 V: 79 BTU/h |
1/8 of max output power @ 4 Ω |
|
115 V: 229 BTU/h |
230 V: 251 BTU/h |
|
Live performance DSP amplifier. Fully integrated professional speaker processing with FIR Drive technology . Market leading acoustic performance and rock solid reliability. True 2 ohm stability. Intuitive system control software, makes setup and control easy. Rated power: 2 Χ 3000 Watts/2Ω, 2 Χ 2500 Watts/2,6Ω, 2 Χ 1700 Watts/4Ω, 2 Χ 900 Watts/8Ω.
Manufacturer |
DYNACORD |
Application |
Portable PA |
Channels |
Dual Channel |
Resistance ohms |
8Ω / 4Ω, 2Ω |
DSP |
Yes |
Weight (kg) |
18,2 |
Power (8 ohms/Watt RMS) per channel |
900 |
Power (4 ohms/Watt RMS) per channel |
1700 |
Power (2 ohms/Watt RMS) per channel |
3000 |
Series |
L series |
Model |
L3600FD |
Part Number |
F01U312397 |
Warranty |
3 Years Warranty |
|
- 2900W RMS x 1 at 2 ohms
- 1780W RMS x 1 at 4 ohms
- 975W RMS x 1 at 8 ohms
- 2525W RMS x 2 at 2 ohms
- 1510W RMS x 2 at 4 ohms
- 890W RMS x 2 at 8 ohms
- 2 channel independent, fourth-order Linkwitz-Riley crossovers
- DDT protection
- Revolutionary IPR class D topology
- Detented input controls
- Combination XLR 1/4 inputs
- 4 pole twist lock output connectors
- Ultra-light weight
- Individual signal pass 1/4" jacks on each channel
- LED illuminated
- Standby, LED power present indication
- Weight Unpacked: 6.2 kg
- Weight Packed: 7.9 kg
- Width Packed: 53.34 cm
- Height Packed: 53.848 cm
- Depth Packed: 15.24 cm
|
Model T4n Product Type Power Amplifier Output Power (W) 1kHz THD+N=1% (120V) 2Ω per channel 2200 4Ω per channel 1950 8Ω per channel 1150 4Ω bridge 4400 8Ω bridge 3900 Output Power (W) 1kHz 20mS burst (120V) 2Ω per channel 2900 4Ω per channel 1950 8Ω per channel 1150 4Ω bridge 5800 8Ω bridge 3900 SN ratio (20Hz-20kHz) 106dB THD+N 20Hz-20kHz, Half Power RL-4Ω, 8Ω Intermodulation Distortion 60Hz: 7kHz, 4:1, Half Power 0.1% Frequency response RL=8Ω,Po=1W,HPF=OFF 20Hz-20kHz (Max) 0dB Frequency response RL=8Ω,Po=1W,HPF=OFF 20Hz-20kHz (TYP) 0dB Frequency response RL=8Ω,Po=1W,HPF=OFF 20Hz-20kHz (MIN) 6dB Channel Separation (Half Power RL=8Ω,1kHz Att. max input 600Ω shunt) 70dB Residual Noise Att,min 20Hz-20kHz(DIN AUDIO) -70dBu Damping factorRL=8Ω 1kHz 800 Voltage Gain Att.max 26dB Maximum Input Voltage +24dBu Input Impedence 20kΩ (balance) 10kΩ (unbalance) Controls Specifications Front Panel POWER switch(push on/push off) attenuator (31 position) x2 Rear Panel MODE switch (STEREO/BRIDGE/PARALLEL) X1; HPF switch (20Hz/OFF 12dB/oct) x1; AMP ID switch (6PDIP)x1 Connectors Specifications Input XLR-3-31 type/ch; Euroblock connector (balance)/ch Output SPEAKON/ch, 5way biding postx1 Date Port RJ45x2 Indicators Specifications Power/Standby x1 (Green/Orange) Remote x1 (Green) Protection x1 (Red) Temp x1 (Red) heatsink temp 85°C Signal x2 (Green) Mute x2 (Red) Clip/Limit x2 (Red) Load protection POWER switch on/off mute; DC-fault: power supply shutdown / do not return automatically Cooling Variable-speed fan: x2 Power requirements 120V/60Hz Weight 14.0 kg Dimensions (W x H x D) 480 x 88 x 456mm (2U)
|
Reviews
There are no reviews yet.