| Content |
The P2110-T is a weatherproof full range, wide-dispersion, coaxial two way loudspeaker system for small and medium size distributed systems.
The high frequency section is a constant directivity horn loaded to a 1” RCF Precision Neodymium compression driver with a 1.50” diaphragm assembly for smooth, wide dispersion. The low-frequency transducer is a 10” woofer with a 2.5” voice coil. The cabinet is equipped with 12 x M 8 brass inserts, a stainless steel U-Bracket and pair of spacers for 90° mounting.
The system features a selectable line transformer for 70 - 100 Volt applications/installations, it meets the requirements of IP 55 code (International Protection Rating)
| Features |
|---|
| Cabinet is a single piece rotational moulded in medium density polyethylene, fully UV protected and waterproof IP 55 | | Front grille in custom perforated aluminium with open-cell fibres and water repellent woven fabric backing | | Stainless steel bracket | | One 10" high-output LF transducer with 2" voice coil | | One RCF Precision Neodymium 1" Compression Driver with 1.5" voice coil | | 90° x 40° constant directivity horn | | Built in passive crossover and selectable line transformer | | 10° X 20° enclosure sides for array configurations | | Active Mosfet Compression Driver Protection | | LICC (Low Impedance Compensated Crossover) network | |
12 brass suspension points (M8)
| Acoustical Specifications |
|---|
| Frequency Response -10 dB: | 95 Hz | ÷ 20 kHz | | Frequency Response -3 dB: | 120 Hz | ÷ 20 kHz | | Max SPL @ 1m: | 118 dB | | | Horizontal coverage angle: | 90° | | | Vertical coverage angle: | 40° | | | Directivity index; Q: | 11 | | | System Sensitivity: | 95 dB | | | Nominal Impedance: | 16 Ω | | | Power Handling: | 200 Watt | | | Peak Power Handling: | 800 Watt | | | Recommended Amplifier: | 400 | | | Protections: | Dinamyc | | | Crossover frequencies: | 2000 Hz | |
| TRANSDUCERS |
|---|
| Compression Driver: | 1.5" HF driver, 1" voice coil | | | Nominal Impedence: | 8 Ω | | | Input Power Rating: | 25 Watt AES | | | Sensitivity: | 106 dB | | | Woofer: | 10" woofer, 2.5" voice coil | | | Nominal Impedence: | 16 Ω | | | Input Power Rating: | 180 Watts AES | | | Sensitivity: | 95 dB | |
| INPUT SECTION |
|---|
| Input connector: | 5m, 4-adriges Neopren Kabel | | | Constant voltage transformer: | 70/100 | | | Power Selection: | 70V/30W ,15W , 100V/60W, 30W | |
| CABINET |
|---|
| Cabinet Material: | Polyethylene rotomoulded | | | Hardware: | 12 x M8 inserts+ U-brackets and pair of spacers | | | Grille: | Custom perforated aluminium grille with open-cell fiber and water repellent woven fabric backing | | | Colour: | Grey | |
| PHYSICAL SPECIFICATIONS |
|---|
| Height: | 350 / 13.78 mm/inch | | | Width: | 350 / 13.78 mm/inch | | | Depth: | 320 / 12.60 mm/inch | | | Net Weight: | 13.5 / 29.75 Kg/Lbs |
|
|
Passive Reinforcement speaker 300W / 8ohm – 127dB SPL
Comprising four versatile loudspeaker enclosures for either portable use or fixed installation, FBT is debuting the VENTIS range at Pro Light + Sound 2016. Available in either passive or bi-amplified versions, each of the models – the VENTIS 115, 112, 110, and 206 – has been designed to meet the highest standards in both performance and aesthetic appeal.
For the VENTIS range, quality and flexibility are the watchwords. Based on a powerful combination of B&C compression drivers and FBT’s own custom, long excursion woofers, the 115, 112 and 110 models are two-way, bass reflex designs housed in 15mm birch plywood. A full-grille design backed by specially treated acoustic cloth delivers the characteristic style for which FBT is known, while fully rotatable constant directivity horns ensure accurate coverage.
The three enclosures are as suitable for fixed installation as they are for use on the stage. M10 points are included as standard while an optional U-bracket can be used for wall-mounting. For use on the road, the VENTIS models include aluminum handles with rubber inserts, a 35mm polemount socket, and a 45° sloped profile for unobtrusive placement on-stage as a monitor.
Meanwhile the multi-purpose VENTIS 206 can be deployed as a front fill, an under-balcony fill, as a main providing pristine speech intelligibility or simply as the full-range companion of a subwoofer. Constructed in 12mm birch plywood, the 206 has an integrated rear handle, an optional mounting bracket and, most importantly, an astonishing size to SPL ratio.
- 2-way, bass reflex design
- Digital Signal Processor with graphic display
- 15 mm (0.59”) birch plywood scratch resistant enclosure and internal bracing
- High efficiency switch mode power supply
- Control Panel features balanced XLR/Jack input, XLR LINK OUT, 2 x Volume, RCA Stereo input, DSP display with rotative encoder and push
- ORIGINAL / LIVE The renowned, smooth FBT sound
- VOCAL A special EQ setting to maximise speech intelligibility
- DJ Designed to keep the energy high and your audience dancing
- TOURING The reliability and the roar of the industry’s most popular touring systems
- LOUDNESS The ultimate preset for listening at a medium or low volume
- WARM A special setting to emphasise full-bodied, low-mid frequencies.
| Code: |
40682 |
| Configuration: |
2 way |
| Recommended amplifier: |
300 W RMS |
| Long Term power: |
150 W |
| Short term power: |
600 W |
| Nominal impedance: |
8 ohm |
| Frequency response: |
60Hz - 18KHz -6dB |
| Low Frequency woofer: |
10 - 2 coil inch |
| High frequency driver: |
1 - 1.4 coil inch |
| Sensitivity (@1W/1m): |
97 dB |
| Maximum SPL cont/peak: |
122/127 dB |
| Dispersion: |
80° x 50° rotatable HxV |
| Crossover Frequency: |
1.8 KHz |
| Recommended HP filter: |
HP 50Hz - 12-24dB/oct |
| Input connector: |
2 x SPEAKON |
| Net Dimension (WxHxD): |
329x575x325 / 12.95x22.63x12.79 mm/inch |
| Net Weight: |
15.1/33.28 kg/lb |
| Transport Dimension (WxHxD): |
420x675x400 / 16.53x26.57x15.74 mm/inch |
| Transport Weight: |
17.6/38.80 kg/lb |
|
- Equipped with: 2" tweeter and 10" woofer
- Equipped with Yamaha\'s "Wide Dispersion CD Waveguide Horn“
- Rated power: 700 W (PGM)
- Biamp mode
- Setting for floor monitor
- Lightweight but durable wooden cabinet with high quality polyurea coating
- Stand flange mount for two angles
- Rotatable horn and various U-bracket options (UB-DZR10H/V) for flexible setup and placement
- Dimensions (W x H x D): 315 x 537 (with rubber feet) x 345 mm
- Weight: 14.0 kg
|
User\'s manual
Technical drawing
- Passive 2-way bass-reflex installation speaker
- 200 W permanent load capacity
- 118 dB maximum sound-level pressure
- 10" custom woofer and 1" Celestion high-frequency driver
- Rotating CD horn with 80° x 60° dispersion
- For vertical or horizontal use
- speakON-compatible and terminal block input
- 4 x M8 mounting holes
- Shock-resistant front grille for optimum speaker protection
- Extensive range of smart accessories for installation
- Available in black or white
With its streamlined and compact design, the LD Systems SAT 102 G2 is excellently suited for permanent installation and discreet integration into virtually any setting. It features a 10" custom woofer and a 1" compression driver from Celestion, connected to a rotating CD horn with 80° x 60° dispersion. This makes the passive 2-way speaker ideal for both vertical and horizontal use.
The SAT 102 G2 attains a maximum sound-level pressure of 118 dB over a frequency response curve of 65–19 kHz with a permanent load capacity of 200 watts. The reflex casing made of 15 mm MDF has four M8 mounting holes. The inputs are a speakON-compatible socket and a terminal block, while an additional terminal block serves as an output for convenient parallel connection.
Special wall holders are available as an accessory to facilitate wall mounting. The SAT 102 G2 is available in black (Art. No. LDSAT262G2) or white textured finish (Art. No. LDSAT262G2W).
Product type
Installation Loudspeakers
Type
Wall-mounted Loudspeaker
Low/mid driver dimensions
10 "
Woofer size
254 mm
Woofer magnet
Ferrite
Woofer brand
Custom-made
Woofer voice coil (mm)
50.8 mm
Horn
CD horn
HF driver dimensions
1 "
HF Driver Size
25.4 mm
HF driver magnet
Ferrite
HF driver brand
Celestion
Dispersion (H x V)
80 x 60 °
Load rating (RMS)
200 W
Peak power
400 W
Frequency response
65 - 19000 Hz
SPL (1W/1m)
95 dB
Max. SPL
118 dB
Impedance
8 Ohm(s)
Protection circuits
HF Driver
Loudspeaker inputs
2
Speaker input connections
Speakon compatible , terminal block
Loudspeaker outputs
1
Speaker output connections
terminal block
Cabinet material
15 mm MDF
Cabinet surface
texture paint
Cabinet colour
white
Cabinet construction
vented
Width
300 mm
Height
550 mm
Depth
270 mm
Weight
12,2 kg
| The PS-10 JB-Systems is a compact passive speaker with a woofer 10 "is the perfect choice for small applications where high power is not necessary. It is a versatile device that can be used in different installations, there is even a special holder designed for use as a monitor.
JB-Systems Specification PS-10:
This enclosure is suitable for fixed installation and mobile application, the rugged polypropylene housing provides excellent protection components. SP-10 can be mounted on a stand with a standard speaker connection 35mm and can be mounted easily using the integrated mounting points. And as mentioned earlier, you can use the stand included for use as a monitor. This device also has a sturdy handle for easy transport and rubber feet protect the bottom of your speaker.
- passive Speaker
- 10 "woofer
- 1.35 "compression driver
- Power: 160W RMS, 320W peak
- Impedance: 8 Ohm
- Speakon In / Out
- polypropylene housing
- sturdy handle
- Rubber feet
- Can be mounted on standard stand (35mm)
- Points integrated mounting
- Supplied with bracket for use as a monitor
- Weight: 10.3kg
| Full Range Speaker
- Equipped with: 10" + 1“
- Dispersion: 90° x 60° CD horn
- Power: 300 W RMS
- Impedance: 8 Ohm
- Frequency range: 95 - 19,000 Hz
- Max. SPL: 126 dB
- Flange mount
- 3 x M8 fly points
- 2 Handles
- Connectors: 2 x speaker twist
- Dimensions: 320 x 480 x 290 mm
- Weight: 12.9 kg
|
Reviews
There are no reviews yet.