Content | PV Series The PV amplifier features a two-way crossover and sub-sonic (low-cut) filter for each channel. Crossover frequencies are fixed at 150 Hz, allowing subwoofers to be driven at extremely high sound pressure levels, and the filters cut at 40 Hz to prevent low-end rumble. This unit takes advantage of rugged TO-3P output devices mounted on massive aluminum extrusions and dissipates heat via an extremely quiet and effective two-speed fan/fans. PV amplifiers are designed to operate at line voltages as low as 50% of nominal, employing mammoth toroidal power transformers. This amp is designed to drive a 2-Ohm load per channel, thus achieving awesome performance into 4 Ohms in BRIDGE mode. PV amplifiers are ruggedly constructed, rack-mountable pieces of gear with superb patching capability, allowing superior flexibility in application. Front panel features include calibrated, detented gain (dB) controls and LED indicators for power (PWR), signal presence (SIG), Thermal Protection indicator, and DDT™ activation on each channel, as well as a rocker mains POWER switch. The back panel contains an IEC connector, line voltage selector switch, dual primary fuses, and the critical cooling fan opening. Each channel input section includes a combo XLR / TRS phone jack connector, THRU/LOW out and HIGH out TRS jacks, and activation switches for the LOW CUT filter. Channel output sections feature twist lock connectors. PV2 Power Amp 630 watts per channel at 4 ohms • 370 watts per channel at 8 ohms • 1170 watts bridged at 8 ohms • 12Hz - 35kHz Frequency Respone (Stereo) • 150 Hz Crossover Switch • dual shock-proof binding post speaker output • Input barrier strip for permanent installations • Dimensions Packed (HxWxD): 21.7 x 20 x 6.8 inch / 550mm x 508mm x 173mm - Weight: 45lb / 20.5kg | The S Series of RAM Audio amplifiers distils all these features to fulfill all your needs, whether youʼre starting a P.A. amplifier project from scratch, or you need to upgrade your present sound reinforcement equipment.
In the S Series amps, you'll find five 2-channel models and five 4-channel models, all offering plentiful power levels at low distortion in the range of 1.5 to 6 kilowatts, yet weighing in around 8 kilos and 30 cm deep.
• Ultra-compact and lightweight 2-U high • Laser cut aluminum front panels with integrated carrying handles • Neutrik® XLR input connectors, input and signal link in 2 channel models • Input Link switch: allow daisy-chaining of the input signal • Neutrik® Speakon® output connectors • Detented sealed potentiometers for easy recall of volume settings • ICL™, PMS™, Hi-temp, Signal indicators per channel • Power on and Stand-by leds • Highly versatile with multiple configuration and additional module options • Full PC control via EtheRAM (with EtheRAM Control module) • Switchable ICL™ clip-limiters per channel • Switchable (30-50 Hz) sub-sonic highpass filter per channel • Three-position gain selector (26, 32 or 38 dB) • Dual or bridge mode selector • Twin temperature controlled, back to front cooling fans • Oversized power components (high SOA reserve specification) Standard Signal Inputs Module: The S Series amps are equipped as standard with twin Neutrik® XLR, doubled by two other XLR connectors for linking purposes. In the 4 Channel models an XLR input per channel is provided with the signal linking facility.
Analog Processor Module: permits a very easy, user-friendly signal processing to enable the amp to set up a bi-amp system without any other outboard device. These are the Processor's main characteristics: • 2-way stereo crossover (dual mono or single bridged sub output) • 24dB/oct Linkwitz-Riley configurable crossover (90, 100 o 120Hz) • Adjustable attenuation in the High-pass outputs (-3, -6 or -9dB) • Adjustable Limiter, relative to Max. Output (-3, -6 or -9dB)
DSP44_S Module: Digital Signal Processor fully programmable through an USB port. These are the Processor's main characteristics: • 4 Inputs/4 Outputs or 2 In/2 Out free route configurable. • 24 bits/192 kHz 256x Oversampling Converters. • Output Delay: 0 to 7.1 meters (20.69ms) per channel. • XOver: Up to 48dB/oct Butterworth, Linkwitz-Riley and Bessel. • EQ: 9 filters per channel (Parametric, Shelving, LP,HP,BP,SB). • Gain, Mute and Phase inversion per channel. • RMS Power and Peak Voltage output limiter per channel. • Real Time operation from USB or front panel configuration.
Standard Signal Inputs Module EtheRAM Control Module Ethernet Audio Transport (Coming soon) Analog Processor Module DSP44_S Module EtheRAM Control Module AES/EBU Digital Input (Coming soon)
OUTPUT POWER |
S-1500 |
S-2000 |
S-3000 |
S-4000 |
S-6000 |
S-3004 |
S-4004 |
S-4044 |
S-6004 |
S-6044 |
1kHz, 1.0% THD |
2 ohms |
2x880W |
2x1190W |
2x1570W |
2x1950W |
2x2950W |
4x700W |
4x980W |
- |
4x1440W |
- |
4 ohms |
2x575W |
2x790W |
2x1100W |
2x1380W |
2x2025W |
4x500W |
4x670W |
4x975W |
4x1000W |
4x1480W |
8 ohms |
2x325W |
2x460W |
2x630W |
2x810W |
2x1250W |
4x300W |
4x430W |
4x690W |
4x620W |
4x1015W |
Bridge @ 4ohms |
1760W |
2380W |
3140W |
3900W |
5900W |
2x1400W |
2x1960W |
- |
2x2880W |
- |
Bridge @ 8ohms |
1150W |
1580W |
2200W |
2760W |
4050W |
2x1000W |
2x1340W |
2x1950W |
2x2000W |
2x2960W |
P. N. 12dB C.F. |
2 ohms |
2x975W |
2x1360W |
2x2060W |
2x2460W |
2x4225W |
4x890W |
4x1170W |
- |
4x2080W |
- |
4 ohms |
2x610W |
2x880W |
2x1240W |
2x1600W |
2x2600W |
4x580W |
4x820W |
4x1230W |
4x1280W |
4x2110W |
Frequency Response (power bandwidth ±0.25dB): 20Hz-20kHz Phase Response (@1W 20Hz-20kHz): ±15deg Total Harmonic Distortion (20Hz-20kHz): Intermodulation Distortion (SMPTE): Crosstalk (20Hz-20kHz): >75dB Voltage Gain (selectable): 26/32/38 dB Sensitivity: 1500:2.6/1.3/0.6V 2000:3.0/1.5/0.8V 3000:3.6/1.8/0.9V 4000:4.0/2.0/1.0V 6000:5.0/2.5/1.3V 3004:2.6/1.3/0.6V 4004:3.0/1.5/0.8V 4044:3.7/1.9/0.9V 6004:3.5/1.8/0.9V 6044:5.0/2.5/1.3V Signal to noise ratio: 1500:112dB 2000:113dB 3000:115dB 4000:116dB 6000:118dB 3004:112dB 4004:113dB 4044:116dB 6004:116dB 6044:118dB Required AC Mains (@4ohms 1/8 r.p.): 1500:4A 2000:4.8A 3000:6.2A 4000:7.5A 6000:10.5A 3004:6A 4004:7.5A 4044:11A 6004:10.5A 6044:15A Dimensions (WxHxD): 483x88.9x310 mm - 19x3.5x12.2 inches Weight (Net): 1500/2000: 8Kg - 17.6Lbs 3000/4000/3004/4004/4044: 8.5Kg-18.7Lbs 6000/6004/6044: 8.6Kg-18.9Lbs
Protections: Soft-start, Turn-on Turn-off transients, Muting at turn-on, Over-heating, DC, RF, Short-circuit, Open or mismatched loads, Overloaded power supply,ICL™, PMS™, SSP™ |
Power Rating
Stereo Mode:
8Ω EIA 1 kHz 1% THD - 500W
4Ω EIA 1 kHz 1% THD - 850W
2Ω EIA 1 kHz 1% THD - 1250W
Bridged Mono:
8Ω EIA 1 kHz 1% THD - 1700W
4Ω EIA 1 kHz 1% THD - 2500W
Damping Factor Not Specified By Manufacturer
Input Sensitivity 26dB Setting - 3.28V
32dB Setting - 1.60V
Input Impedance > 10kΩ balanced, or unbalanced
Gain 34.5dB
Frequency Response 20Hz to 20kHz, +/- 0.2dB
Signal-to-Noise Ratio -106dB
Total Harmonic Distortion (THD) 0.02% @ 2Ω
0.005-0.01% @ 4Ω
0.002-0.01% @ 8Ω
Input Connections Input: XLR Male, XLR Female and 3-pin detachable terminal blocks (1 each per channel)
DataPort: HD-15, input signal in parallel with XLR input connectors
Output Connectors Output: Neutrik Speakon (ch 1 wired to both channels) and 5-way binding posts
Controls Front Panel AC Power Switch
Gain Controls, 21 detents, 1 dB steps (each channel)
Controls (Rear) Input Mode: Bridge (Yellow), Stereo (Green), or Parallel (Orange)
Gain / Sensitivity: 26dB (Orange), 32dB (Green), or 1.2V (Yellow)
High Pass (each channel): 3Hz (Off), 30Hz (Yellow), or 50Hz (Orange)
Clip Limiter (each channel): Off, On (Yellow)
Indicators Clip Limiter (each channel): Off, On (Yellow)
Camera Resolution Flow-thru air path and solid aluminum heat sinks
Power Consumption 120V 50/60Hz - 8.5A
230V 50Hz - 7.5A
Power Requirements Not Specified By Manufacturer
Dimensions (WxHxD) 19 x 3.5 x 15.63" (48.3 x 8.9 x 39.7cm)
Weight 33.5 lbs (15.2kg)
Specialties Parallel Dataport, XLR/M and XLR/F connectors for simple loop-through connectivity
|
A full model revision takes Yamaha's high-end PC-N power amplifiers to the next level - the PC-1N
Series. The new PC-1N Series amplifiers feature an extraordinarily solid low end, rich midrange,
and superbly defined highs. They also deliver fast response and exceptional stability even in the face
of serious power supply limitations. Refinements throughout this expanded five-model lineup make
these amplifiers the new benchmarks for quality, reliability, and versatility in professional applications.
Frequency Response: 10 Hz – 40 KHz. Output Power: 2 x 400 Watt / 8Ω RMS, 2 x 700 Watt / 4Ω RMS,
1400 Watt / 8Ω bridge RMS. Weight: 13 Kg. |
Number of Channels: 2
Output Power: (per channel)
8 ohms 450W
4 ohms 850W
2 ohms 1550W
Output Power: (bridged)
8 ohms 1700W
4 ohms 3100W
THD%: (@1dB below max output)
@ 1kHz |
The high efficiency of the ED series enables maximum efficiency with low heat generation.
A new and unique Class-H circuity technology using state of the art SMD Surface Mount Technology with a reduced number of components offering performance levels exceeding audiophile levels like a slew rate of 50V/µs and high-end extended dynamic sound. The 2U amplifier provides 2x550W into 4 Ohm is equipped complete with temperature-controlled fan cooling, all common protective circuits such as over-temperature, short circuit, RFI and soft start.
The integral soft clip limiter protects against damage to the connected loudspeakers, the activity of a protective circuit, signal and limiter are shown for each channel by LEDʼs.
AMPLIFIER SPECIFICATIONS |
---|
Power output stereo 4Ω: | 2 x 550 Watt rms | | Power output stereo 8Ω: | 2 x 265 Watt rms | | Power output bridged 8Ω: | 1100 Watt rms | | Frequency Response: | 20 Hz ÷ 20 kHz | | Signal/noise rate: | > 105 dB | | Crosstalk: | > 70 dB | | Distortion (THD+N): | | | Intermodulation: | | | Damping factor: | 200:1 (8 Ω) | | Slew rate: | 50 V/μS | |
INPUT SECTION |
---|
Input connector: | 2 x XLR balanced, 6,3mm jack unbalanced | | Input sensitivity: | 0 / 0.775 dBm/V RMS | | Input impedance: | 10 kΩ | | Controls: | Volume control for each channel | |
OUTPUT SECTION |
---|
Output connector: | 2 x Neutrik Speakon 4 ways | |
SYSTEM PARAMETERS |
---|
Cooling: | Two-speed fan | | Protections: | Thermal, direct current, RFI, short circuit, transformer protection | | Amplifier class: | H | |
POWER REQUIREMENT |
---|
Operating voltage: | 220÷240 / 110÷120 ~ 50 / 60 V ~ Hz | | Max.current: | 10 A | | Power Consumption: | 2200 W | |
PHYSICAL SPECIFICATIONS |
---|
Height: | 88 / 3.46 mm/inch | | Width: | 483 / 19.01 mm/inch | | Depth: | 350 / 13.77 mm/inch | | Net Weight: | 15 / 33.06 Kg/Lbs | |
SHIPPING INFORMATION |
---|
Package height: | 120 / 4.72 mm/inch | | Package width: | 540 / 21.25 mm/inch | | Package depth: | 475 / 18.07 mm/inch | | Shipping Weight: | 17 / 37.47 Kg/Lbs |
|
Reviews
There are no reviews yet.