| Content | Handheld Audio Analyzer with USB Interface
- Built-in calibrated measurement microphone
- 1/3 octave real-time analyzer
- 31-band EQ setting value display (boost/cut)
- RT60 measurement
- Phase checker
- Noise generator with pink noise, 1kHz and polarity test signal, balanced output
- Memory and average calculation function
- SPL meter calibration through sound level calibrator
- Sound Pressure Level Meter from 30 dB~130 dB
- Line signal measurement display in dBu, dBV, or Volts (AC)
- SPL meter and level meter have three level range selections
- Maximum level, Peak hold displays
- XLR input and output sockets
- USB interface for desktop software control
- Audio test signal CD and supporting software
- Three power modes: (1) Power Save (2) On (3) Off
- Operates seven hours with four AA batteries
- AC power adapter included
| With the PAN05, two microphone signals can be mixed down to one. Since decoupling occurs via the balanced resistor network, the PAN05 also lets phantom power "pass through“, useful for condenser microphones. However, due to the difference in sound and signal level, mixing dynamic and condenser mics should be avoided. Best results will be achieved using two identical mics.
SPECIFICATIONS:
- Input: 2 x XLR/f balanced
- Nominal impedance: 200 Ω
- Output 1 x XLR/m balanced
- Load impedance >200 Ω
- Symmetrically decoupled through resistors
- Total ohmic value: 200 ohms
- Typical attenuation: 6 dB
- Housing: metal casing 110 x 73 x 42 mm
|
Palmer Pro MCT DMX 3-pin and 5-pin DMX and XLR cable tester
MCT DMX
This cable tester checks 3-pin and 5-pin DMX cables for continuity in fully automatic or manual pin selection modes. Pin connection status of the male and female cable ends is indicated by two rows of bright LEDs. In addition, the unitʼs 3-pin connectors can also be used to test XLR microphone cables. The DMX Cable Tester comes with two L-brackets for variable mounting options.
- Tests 3-pin and 5-pin DMX cables for continuity
- Also tests 3-pin XLR microphone cables
- Automatic test mode or manual pin 1 - 5 selection
- LED indicators
- Mounting brackets included
Product type
Test Equipment
Connectors
XLR (3-pin) , XLR (5-pin)
Controls
Auto Scan , On / Off , Scan switch
Indicators
LED chain
Operating voltage
2 x AA battery
Acoustic continuity test
no
Test cable
no
Cabinet material
sheet steel
Cabinet surface
powder coated
Width
240.2 mm
Height
48 mm
Depth
53 mm
Weight
0,7 kg
|
The MiniSPL is the perfect accessory to the Acoustilyzer & Minilyzer for
acoustical measurements.
The MiniSPL is a battery powered measurement microphone. Together
with the Acoustilyzer or Minilyzer, it forms an acoustical analyzer and integrating
sound level meter. Additionally it may be operated as a stand-alone microphone
e.g. connected to a balanced audio-line, a microphone-input or a sound-card.
Product-details
? Battery powered
? Factory-set sensitivity
? No phantom power required
? 1/2" microphone, class 2 acc. IEC 61672
? Omni-directional
? Supplied with mic clamp, wind protection
? Typical frequency response included
MiniSPL together with Acoustilyzer:
? SPL Meter / RTA
? Reverberation Time RT60
? Delay Time
? FFT Analyzer
? Speech Intelligibility STI-PA
MiniSPL together with Minilyzer:
? Measurements: SPL, min./max., Leq
? 1/3rd octave spectrum analyzer |
| Model Number |
JZK-601 |
| Memory groups |
32*2 groups |
| Product Dimensions |
14.3* 9.3* 3.8 CM |
| Business type |
Manufacturer |
| Storage temperature |
-20-50°C |
| Storage Humidity |
15%-90%RH |
| Operating temperature |
5-40°C |
| Operating Humidity |
40%-85%RH |
| Display |
LCD crystal digital display |
| Measuring method |
Infrared radiation temperature measurement |
| Measurement range |
32~42.5℃ fro human body, 0-100℃ for objects |
| Resolution |
0.1 degrees Celsius (0.1 degrees Fahrenheit) |
| Accuracy |
0-39.9kpa(0-299 mmhg) |
| Voltage |
3 V |
| Power consumption |
|
|
ARTSOUND A8862 LASERGRIP THERMOMETER
Temperature range: -32 C - 550 C
Accuracy: 1,5%
Power supply: 9V
Weight: 258gr
|
Reviews
There are no reviews yet.