| Content |
XLR Line Outputs Levels:
Signal to Noise Ratio:
Crosstalk:
Total Harmonic Distortion:
Digital I/O Format:
Sampling Frequency:
D/A Resolution:
Clock Source:
Word Clock I/O
General Specifications:
Power Requirements:
Power Consumption:
Dimensions:
Weight:
SMPTE Standard
+4dBu Nominal Level, (-24dB Full Scale)
+24dBu Maximum Level
TASCAM Standard
+4dBu Nominal Level, (-16dB Full Scale)
+16dBu Maximum Level
EBU2 Standard
+6dBu Nominal Level, (-9dB Full Scale)
+15dBu Maximum Level
>100dB (IHF-A)
>70dB (Adjacent Channels @ 10kHz)
|
Optional 8-channel D/A card with specifications matching those of the A/D section,
turning the Trak2 into a complete digital audio conversion system with two A/D
channels and up to 8 D/A. |
Power and Options...
The Apogee X-Series FireWire Card gives you the power and convenience of a
direct connection to any FireWire equipped computer. The X-FireWire Card uses
an expansion slot in the ROSETTA 800 to give users of Logic, Nuendo and other
popular software the option of amazing sounding Apogee conversion. Using Apple?s
Core Audio FireWire driver for Macintosh and ASIO drivers for Windows, your
hardware options for your DAW are greatly expanded.
eXpandability...
The two ports on the Apogee X-FireWire Card allow you to daisy-chain additional
devices to create an entire system. By extending the bus, the X-FireWire card
allows for daisy-chaining of multiple Apogee systems or compatible peripherals,
and permits the use of multiple FireWire devices by computers with only one port.
The card also passes power through the FireWire ports to allow the powering of
additional devices. (Note: This feature is available for Windows systems only at this time).
Get Connected
With and X-FireWire card installed in an AD-16X, DA-16X, Rosetta 200 or Rosetta 800
you have the power of a professional FireWire connection to your favorite DAW: Logic 7,
Nuendo, Cubase, Cakewalk, Live or virtually any native audio production software.
Low Latency with FireMix
FireMix is a mixer application that allows control and creation of customizable sub-mixes
for low latency performance in the native environment. FireMix features accurate input and
output metering, 16bit fader control, and eight 48bit mix busses with enough DSP headroom
to insure that there are no compromises to the audio quality. FireMix also has customizable
pan control and key modifier user preferences to allow FireMix to operate in the same manner
as your favorite audio application. With FireMix, you will get low latency monitoring, have the
ability to save and recall all of your mixes, group and ungroup master faders all with little to no
impact on your CPU performance.
Features:
* 2, S400 FireWire connectors, allowing convenient chaining of multiple units
* Compatible with Apple's OS X built-in FireWire Core Audio driver
* Supplied with Windows XP WDM/ASIO driver
* Up to 8x8 24bit at 88.2/96k
* Up to 4x4 24-bit channels at 176.4/192KHz
* Fully compliant and compatible with 61883-6 and other relevant 1394 IEEE
and AES specifications
* Allows low-jitter synchronization to a FireWire audio network and can provide
a master clock source for a FireWire audio network
|
The Tascam LA-40 MKIII has been primarily designed to provide matching capabilities between professional equipment and semi-professional or consumer equipment. It consists of four RCA inputs and outputs (–10 dBV, unbalanced) as well as four XLR inputs and outputs (+4 dBu/–20 dBu, balanced) which enable the user to connect for instance four tracks of a multitrack recorder (ins and outs) to a balanced mixer ensuring optimum level and impedance matching. Also, a switch matrix allows channels to be linked, utilizing the converter as a distribution amplifier for splitting signals to multiple recorders, or for multizone sound routing applications.
Switches on the bottom panel allow to select a nominal level of +4 dBu or –20 dBu for each channel and ±12 dB trim pots on the front panel make perfect level matching easy. LEDs on the front panel indicate signal presence for each channel. The LA-40 MKIII has also ground lift switches for each channel and a combined master switch to avoid ground loops.
Main Features
* 4 channels with unbalanced RCA inputs and balanced XLR outputs
* 4 channels with balanced XLR inputs and unbalanced RCA outputs
* XLR nominal level selectable between +4 dBu and –20 dBu
* Trim pots for each channel on front panel (±12 dB)
* Signal LED for each channel
* Ground lift switches for each channel and master switch
* Distribution amplifier functionality: One mono input signal can be routed to all four output channels, or one stereo input signal can be routed to two channels each (RCA to XLR and XLR to RCA)
* Internal power supply, no AC adapter needed
* 1 U rack-mountable chassis
Specifications
Inputs and outputs (unbalanced to balanced)
Inputs 4 RCA jacks (unbalanced)
Input impedance 23 kOhm (when all INPUT LINK switches are OFF)
5.7 kOhm (when all INPUT LINK switches are ON)
Nominal input level –10 dBV, ±1 dB
Maximum input level +4.8 dBV
Indicator detection level –36 dBV or more (OUTPUT LEVEL switch set to +4 dB or –20 dB)
Outputs 4 XLR-type connectors (balanced, Pin 1 = ground, Pin 2 = hot, Pin 3 = cold)
Output impedance 94 Ohm
Nominal load impedance 10 kOhm
Minimum load impedance 600 Ohm
Nominal output level +4 dBu, ±1 dB (OUTPUT LEVEL switch set to +4 dB)
–20 dBu, ±1 dB (OUTPUT LEVEL switch set to –20 dB)
Maximum output level +23 dBu
Inputs and Outputs (balanced to unbalanced)
Inputs 4 XLR-type connectors (balanced, Pin 1 = ground, Pin 2 = hot, Pin 3 = cold)
Input impedance 54 kOhm (when all INPUT LINK switches are OFF)
13.5 kOhm (when all INPUT LINK switches are ON)
Nominal input level +4 dBu, ±1 dB (INPUT LEVEL switch set to +4 dB)
–20 dBu, ±1 dB (INPUT LEVEL switch set to –20 dB)
Maximum input level +30 dBu (INPUT LEVEL switch set to +4 dB)
+8 dBu (INPUT LEVEL switch set to –20 dB)
Indicator detection level –22 dBV or more (INPUT LEVEL switch set to +4 dB)
–46 dBV or more (INPUT LEVEL switch set to –20 dB)
Outputs 4 RCA jacks (unbalanced)
Output impedance 200 Ohm
Nominal load impedance 10 kOhm
Minimum load impedance 1 kOhm
Nominal output level –10 dBV, ±1 dB
Maximum output level +18 dBV
Audio performance
TRIM range ±12 dB
S/N ratio (at nominal levels) 90 dB(A) (20 kHz LPF)
87 dB(A) (20 Hz HPF and 20 kHz LPF)
Total harmonic distortion
(1 kHz, at nominal levels) 0.005 % or less
Frequency response (at nominal levels) 20 Hz – 100 kHz, ±3 dB
Crosstalk
(1 kHz, nominal levels, 600 Ohm load) –90 dB
Other specifications
Power requirements 100–240 V AC, 50/60 Hz
Power consumption 6 W
Dimensions (W x H x D) 483 mm x 44 mm x 280 mm
Weight 3 kg
|
Input MADI: 1 x BNC, 1 x optical
Output MADI: 1 x BNC, 1 x optical
Input ADAT optical: 8 x TOSLINK, 24-Bit, Bitclock PLL
Output ADAT optical: 8 x TOSLINK, 24-Bit
Input word clock: BNC, Signal Adaptation Circuit (functional from 1.2 Vpp input signal), switchable termination
Output word clock: BNC, low-impedance driver stage, 4 Vpp into 75 Ohms, short-circuit-proof
MIDI input and output: via two 5-pin DIN jacks
Sync sources: MADI, ADAT optical, word clock, internal
Varipitch: by input signal or word clock
Sample rates: 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, variable (Sync/word clock)
Sample rate range: MADI: 32 kHz - 96 kHz, word clock: 27 kHz-105 kHz, ADAT: 33 kHz - 57 kHz
Jitter: Internal clock
Jitter suppression on external clock: circa 30 dB (2.4 kHz)
Jitter sensitivity: all PLLs operate even at 100 ns Jitter without problems
Power supply: internal switching mode ps, 100 V-240 V AC, 50-60 Hz, 10 Watts
Dimensions: 483 x 44 x 200 mm
|
The Apogee X-Digi-Mix expansion card allows for direct connectivity between
Pro Tools Mix systems and the Rosetta 200 or Rosetta 800. The X-Digi-Mix
card provides superior quality conversion to Pro-Tools Mix users without the
need for an additional interface, and effectively extending the life of their Mix
systems for years to come.
Features:
* Standard Digidesign peripheral connector for interfacing directly to Mix Core
or Farm cards.
* Superclock (FSx256) output for convenient integration into existing Pro Tools
configurations.
* With necessary Pro Tools hardware expansion, multiple Rosetta-800s may be
connected into a system.
* Rosetta 800 may be used alongside an Apogee AD-8000 or Trak 2 outfitted with
an AMBUS-Digi8+ card as well as any other Pro Tools Mix-compatible hardware.
* Multiple slaved Rosetta 800s may lock to Word Clock or directly to the Digi-mix
card for low jitter synchronization of the Pro-Tools system.
|
Reviews
There are no reviews yet.