| Content |
This remote device provides programmable rotary switch program selection for the dbx DriveRack 220i and 260 devices. It also provides rotary switch programmable source selection, page assignment, or scene selection for the dbx ZonePro devices. It has DIP switches allowing identification with connection to the processing device via CAT 5 cable on RJ-45 connectors. |
| | - CONVENIENT INSTALLATION AND CONSTRUCTION WITHOUT NEED OF ID SETTING. - SELECTION OF VARIOUS CHIME BROADCASTINGS FOR MIC BROADCASTING (PRE/POST). - CONVENIENT PRIORITY BROADCASTING. - ADOPTION OF OUTPUT SIGNAL LEVEL DISPLAY. - ADOPTION OF RS-422 COMMUNICATION METHOD TO SUPPORT A LONG DISTANCE. | | | | | | | | Audio Output | 0dB(Balanced) | | Audio Input | Paging & RM MIC & LM MIC | -50dB(Balanced) | | BGM(Main & Local) | -10dB(Balanced) | | Tone Control (100Hz & 10kHz) | Paging MIC | ± 10dB | | Audio Output | ± 12dB | | Frequency Response | BGM | ± 3dB | | MIC | ± 3dB | | S / N | BGM | Better than 75dB | | MIC | Batter than 65dB | | T.H.D. | BGM | Less than 0.05% | | MIC | Less than 0.05% | | Priority Control | Paging MIC > DRP > RM1> RM2 > RM3 > RM4 > LM-8000 > Main BGM | | Phantom Power | DC 24V | | Serial Interface | Communication Speed | 9600bps | | Communication Distance | Maximum 300m(UTP CAT%) | | Operation Temperature | -10℃ ~ +40℃ | | Power Source | 100-120VAC or 220-240VAC; 50/60Hz (Supplied AC mains transformer depends on country requirements) | | Weight(SET) | 1.5kg / 3.2lb | | Dimensions(SET) | 200(W) x 70(H) x 206(D)mm 7.9(W) x 2.8(H) x 8.1(D)in | | ※ Specifications and design subject to change without notice. | | | |
|
- PRIORITY CONTROL It controls the priority of emergency, timer, remote1, remote2, main(normal). - AUTO FIRE SENSOR The fire alarm will be given automatically to the designated areas by detecting fire sensor input. - SPEAKER SWITCHING ON EMERGENCY OR NORMAL(MAIN) You can control the speaker relay on emergency or normal(main) mode by using the speaker switch on front panel. - DISPLAY STATUS You can easily check the priority status. - 2 AND 3 WIRE SPEAKER LINE SYSTEM You can control the speaker line on the 2 wire system or 3 wire system. - EXTENSION FUNCTION You can easily expand by connecting additional ECS-616. ![]()
| ECS-616 | | Priority Control | Emergency >Timer > Remote1 > Remote2 > Main | | Link in/ out Interface | RS-422(19200bps,Data 8bits,Stop 1bit, Non Parity bit, Start1bit) | | Link in/ out interface Distance | 1.2 km | | Operation Temperature | -10 °C ~+ 40 °C | | Power Source | 24V DC | | Power Consumption | 900mA | | Weight | 4.8Kg/10.6Ib | | Dimensions( W x H x D) | 482(W)x 88(H) x 380(D) mm / 19(W)x 3.5(H)x 15(D)in | | ※ Specifications and design subject to change without notice. |
|
| | - IT CAN CHECK SPEAKER WIRE OPEN, SHORT, AND EXCEED VALUE ACCORDING TO SETTING UP IMPEDANCE. - IT AUTOMATICALLY CHECKS SPEAKER WIRES BY PROGRAM TIMER OPERATIONS. THE POSSIBLE SET UP TIMES ARE BETWEEN 20 MINUTES AND 200 MINUTES. - RS-232C TERMINAL IN/OUT CONTROL WITH AMX/CRESTRON INTERFACE. - DC 24V OPERATION. - COMPACT DESIGN 2RU(3.5”). - KEEPS STORED VALUES BY NON VOLATILE MEMORY - ALERT SOUNDS WHEN FAULT IS FOUND - BUZZER ON/OFF FUNCTION. | | | | | | SC - 624 | | Power source | 24VDC | | Power Consumption | 300mA | | Weight | 5.2Kg / 11.5lb | | Dimensions (WxHxD) | 1482 x 88 x380mm /19 x 3.5 x 15in | | | |
|
The JBL MTC-300T150 150 Watt Transformer is intended for use with 70V or 100V distributed loudspeaker lines. It is ideally suited for the Control Series 300, especially the 300BB12 Backbox which includes a preinstalled mounting location. |
toa-at-100upr Build-in Attenuator with Relay
Toa - 100V installation
Build-in Attenuator with Relay 100 W / 100 V
|
Reviews
There are no reviews yet.