| Content |
Η τεχνολογία VSS3-reverb που έχει ενσωματωθεί στο Μ3000 αποτελεί πλέον μέτρο σύγκρισης στη μουσική βιομηχανία. Το Μ3000 περιλαμβάνει μερικά από τα πιο εύχρηστα, ποιοτικά και ευέλικτα reverbs για μουσική και ταινίες στην αγορά. Συνδυάζοντας τον απόλυτο έλεγχο στα early reflections με τη διαφάνεια και τις τέλειες αρμονικές στον ήχο του βάθους, η τέχνη του reverberation ανεβαίνει σε νέα επίπεδα.
Με διπλή μηχανή που επιτρέπει στη ταυτόχρονη χρήση 2 reverbs ή εφέ, βραβευμένο user interface, 600 factory presets και πολλαπλές εισόδους και εξόδους, το Μ3000 είναι μια από τις καλύτερες επιλογές για επαγγελματικού επιπέδου reverb.
Technical Specification
Digital Inputs and Outputs
Connectors XLR (AES/EBU)
RCA Phono (S/PDIF)
Optical (Toslink, ADAT)
Formats AES/EBU (24 bit), S/PDIF (24 bit), EIAJ CP-340, IEC 958,
EIAJ Optical (Toslink), ADAT Lite pipe
Output Dither HPF TPDF dither 8-24 bit
Word Clock Input RCA Phono, 75 ohm, 0.6 to 10 Vpp
Sample Rates 44.1 kHz, 48 kHz
Processing Delay 0.2 ms @ 48 kHz
Frequency Response DIO 20 Hz to 23,9 kHz +0,01/-0,1 dB @ 48 kHz
Analog Inputs
Connectors XLR balanced (pin 2 hot)
Impedance 20 kohm
Max. Input Level +22 dBu (balanced)
Min. Input Level (for 0 dBFS) -10 dBu
Sensitivity @ 12 dB headroom: -22 dBu to +10 dBu
A to D Conversion 24 bit (1 bit, 128 times oversampling
A to D Delay 0.8 ms @ 48 kHz
Dynamic Range >103 dB (Unweighted), >106 dB (A)
THD -95 dB (0,0018 %) @ 1kHz
-6 dBFS (FS @ +16 dBu)
Frequency Response 10 Hz to 20 kHz: +0/-0.2 dB
Crosstalk 100 dB (unweighted), >104 dB(A)
THD -86 dB (0.005%) @ 1 kHz
-6 dBFS (FS @ +16 dBu)
Frequency Response 10 Hz to 20 kHz: +0/-0.5 dB
Crosstalk |
Innovation
The ARX AFTERBURNER? is a unique Multi Mode compressor/limiter
designed for use in any professional audio dynamics control application.
Multiple Modes
The Afterburner can be set up and used in three different ways:
In Two channel mode, it performs as two independent compressor/limiters,
with 'industry standard' variable Threshold, Ratio and Output gain. In stereo
mode, our New Adaptive Stereo Link circuitry provides increased stereo
imaging accuracy when linking both channels as a stereo pair. A single front
panel switch puts the Afterburner into its alternative Mono mode, setting it up
as a Single channel, Dual Band compressor/limiter, with separate dynamics
control of both Low and High frequencies, opening up a whole new range of
gain control techniques.
Enhance Switch
In any mode, the Afterburner features an 'Enhance' switch, which provides
frequency restoration to preserve the spectral balance of the audio signal,
compensating for the sagging Low and High frequency response of compressed
program material. Think of it as a 'smart' loudness control.
Features
Switchable Modes - Stereo; Dual Channel Single band; or Single Channel
Dual Band (Low and High)
Low and High frequency compression in Single Channel mode
'Enhance' switch restores spectral balance of compressed signal
New Hard/Soft knee compression switch
New Adaptive Stereo Link circuit for accurate stereo imaging
New Above/Below Threshold LEDs enable at-a-glance compression
confirmation
Balanced XLR and Jack Inputs and Outputs
Sidechain Insert points
Intuitive user-friendly layout
Flawless performance
New Above/Below Threshold LEDs enable at-a-glance compression confirmation
New Hard or Soft knee compression option
New LED metering provides accurate Level status, with separate Gain Reduction
metering in easy to read 'wide scale' meters. There is also comprehensive LED
indication of all operating functions and status in any mode.
Balanced Inputs and Outputs
On the rear panel, each channel has true differential Balanced inputs and outputs,
on both XLR and TRS jack connectors. As well, each channel has a TRS jack
Sidechain access insert point, for applications such as De-essing (when used with
an external equalizer such as the ARX Multi Q or EQ 260).Other features include a
true Hardwire bypass switch for each channel, and passive RFI filters on the inputs.
Universal AC Power
AC power range is a universal 100 to 120V or 220 to 240V AC, and is connected to
the unit via a removable power lead and standard 3 pin IEC connector, with built-in
fuse and voltage change switch.
With its smooth compression, intuitive user friendly layout, high density precision
circuitry, and extensive user-variable operating parameters, the unique ARX Afterburner
is equally at home in Studio, Installation, Broadcast and Sound Reinforcement
environments. It can provide great sounding dynamics control effects that are not
available with any other device.
T E C H N I C A L S P E C I F I C A T I O N S
Input Impedance Balanced 20 Kohms, Unbalanced 10 Kohms
Input Headroom + 22 dB
CMRR >60 dB, 20 Hz-20 KHz
Output Impedance Balanced 300 ohms, Unbalanced 150 ohms
Output Level (Max) + 22 dB
Frequency Response 20Hz to 20KHz ±0.2dB
Signal to Noise ratio -93 dB Unweighted, -99 dB 'A' weighted
Distortion .02% THD @ 0dB,1KHz
Dynamic Range 115 dB
Sidechain Insert Impedance 10 Kohm
Filter Section
Filter Type Phase corrected 6dB/octave
Summed Filter Response ±0.2dB through crossover region
Dividing Frequency 250 Hz
Enhance Section
Low Enhance 50 Hz, High Enhance 10 KHz
Power Requirements 100/120 V AC, 220/240 V AC
Weight 5 lbs/2.2 Kg
Dimensions 19“W x 1?“H x 6“D, 482 x 44 x 155mm
Input/OutputConnector type XLR, Balanced Jack
Sidechain Insert Connector TRS Jack
Front Panel Controls
Hardwire bypass IN/OUT switch
Threshold, Ratio and Output Gain controls
Above/Below Threshold LEDs
12 segment LED Output Level display
Numbered marker panel for labelling compressor assigns
7 segment LED Gain Reduction display
Enhance switch and status LED
Adaptive Stereo link switch and status LED
Dual/Single channel mode switch and status LEDs
Rear Panel Connectors
Balanced Inputs and Outputs, on both XLR and TRS jack
connectors. In Single channel (Mono) mode, use Channel
1 Inputs and Outputs only
Sidechain Insert TRS connector on each channel
AC input connector, with voltage switch and fuse.
|
DPR-504 Νoise gate τεσσάρων καναλιών |
DBX ZONEPRO 640
Ψηφιακός επεξεργαστής αναγγελιών 4 ζωνών. Διαθέτει 6 in/4 out. Διαθέτει AGC
(automatic gain leveler) EQ, crossover, limiter, compressor, noise gate, parametric
EQ, security lockout, AFS περιοριστή μικροφωνισμών, RS 232 για έλεγχο και ρύθμιση
μέσω pc. Δέχεται τα wall panel dbx ZC. ιδανικό για: ξενοδοχεία, εμπορικά κέντρα,
καταστήματα, bar restaurants, cafe.
|
DBX ZONEPRO 1260
Ψηφιακός επεξεργαστής αναγγελιών 4 ζωνών. Διαθέτει 12 in/6 out. Διαθέτει agc (automatic gain leveler)
EQ, crossover, limiter, compressor, noise gate, parametric EQ, security lockout, AFS περιοριστή
μικροφωνισμών, RS 232 για έλεγχο και ρύθμιση μέσω PC, ethernet in & out. Δέχεται τα wall panel
dbx ZC. Ιδανικό για: ξενοδοχεία, εμπορικά κέντρα, καταστήματα, bar restaurants, cafe κτλ. δυνατότητα
να συνδεθεί και με άλλες ίδιες μονάδες και να επεκταθεί.
|
Features
Four Independent Compressor Channels
Channels 1 and 2, 3 and 4 are stereo linkable
7 LED Gain Reduction metering
Balanced XLR Inputs and Outputs
Sidechain Insert points
Intuitive, user friendly layout
Flawless performance
The sheer amount of effects and signal processors necessary for today's standards
of audio production puts a great strain on the available space in equipment racks,
both in the studio and on the road.So, ARX would like to introduce the ARX Quadcomp.
An all-new upgrade of the classic award-winning ARX Quadcomp?, the very first four
channel 1 RU compressor.You?ll notice that we haven?t strayed very far from our
original design concept. The Quadcomp is still four variable ratio Compressor/ Limiters
neatly housed in a compact all steel 1 RU package. However, all new low noise/low
distortion circuitry, better metering plus XLR inputs and outputs put the Quadcomp
in a class of its own.
More Control, Less Space
On the front panel, each channel has the 'industry standard' individual controls for Threshold,
Compression Ratio and Output, plus a new 7 LED Gain Reduction display for accurate visual
indication of the amount of gain reduction being applied to the program, and an IN/OUT
hardwire bypass switch.In addition to this, each channel has a blank numbered panel to write
on for easy confirmation of compressor assigns.
Precision Circuitry
Internally, each compressor uses Class A VCAs and true 2 pole averaging RMS/DC converters
for low distortion and accuracy, plus program dependent attack and release time, which
automatically determines optimum compressor response.
Balanced Inputs and Outputs
The rear panel has true differential Balanced XLR Inputs and Outputs for each compressor.
Each compressor has a TRS jack Sidechain access insert point, for frequency sensitive
compression, De-essing, etc. in conjunction with an external equalizer (such as the ARX EQ260).
Compressor pairs 1 and 2, 3 and 4 also have rear panel mounted Stereo Link switches for accurate
stereo tracking. When switched IN, the first channel becomes the master and controls all the functions
of the second except Output gain.
Universal AC Power
AC power range is switchable 100 to 120V, or 220 to 240V, and is connected to the unit via
a standard IEC connector, with built-in fuse and voltage switch.
Whatever the application ? Channel insert, Bus insert, Master Outputs, Monitor outputs,
Crossover outputs, the Quadcomp II?s unique High Density design, precision Low Noise circuitry
and clean uncluttered layout make it a truly useful audio tool for all applications.
T E C H N I C A L S P E C I F I C A T I O N S
Input Impedance
Balanced 20 Kohms, Unbalanced 10 Kohms
Input Headroom + 20dB
CMRR >50dB, 20 Hz?20 KHz
Output Impedance
Balanced 300 ohms Unbalanced 150 ohms
Output Level (Max) + 20 dB
Frequency Response 20Hz-20KHz ±0.5dB
Signal to Noise ratio
-93 dB Unweighted, -98 dB ?A? weighted
Distortion .015% THD @ 0dB,1KHz
Dynamic Range 108 dB
Attack and Release Times Program dependent
Metering
7 LED display: ?1, 2, 3, 6, 12, 18, ?24 dB
Sidechain Insert Impedance 10 Kohm
Power Requirements
100/120 V AC or 220/240 V AC
Weight 5 lbs/2.2 Kg
Dimensions
19“W x 1?“H x 6“D, 482 x 44 x 155mm
Input Connector type Balanced XLR
Output Connector type Balanced XLR
Sidechain Insert Connector TRS Jack
Front Panel Controls
Hardwire bypass IN/OUT switch
Threshold, Ratio and Output Gain controls
7 LED Gain Reduction display
Marker panel for labelling compressor assigns
Stereo link status LEDs
Rear Panel Connectors
Input and Output balanced XLR connectors
TipRingSleeve Sidechain insert connectors
Channels 1 and 2, 3 and 4 Stereo link switches
IEC AC mains connector with inbuilt fuse and
voltage change |
Αξιολογήσεις
Δεν υπάρχει καμία αξιολόγηση ακόμη.