Content |
GX 230 is a 2 x 30 band graphic EQ with a superb Sound quality
FEATURES: DLT - technologie for perfectly flat amplitude and phase response Variable high-pass and low-pass filters with switchable 6/12 dB lowpass slope In/out switch for instant comparison with flat response 45 mm precision faders Comprehensive frontpanel lay-out Symmetrical in - and output Earth-lift switch Robust mechanical construction Constant Q design Available gain between in- and output: 6 dB Overload indicator: peak-peak sensing circuit giving overload indication for all circuits in the equaliser Failsafe bypass : The input is instantly connected to the output in case of power failure or power supply malfunction Extensive RF suppression XLR on in- and outputs Floating, transformerlike, electronically balanced output stage Power transformer with static screening for rejecting of power line interferences Options - Output transformer - Perpex security cover
SPECIFICATIONS: Input Electronically balanced Absolute overload point +21dBm Impedance 10k (each leg) in parallel with 560 pF equal impedance for "+" and "-" legs Connectors XLR-3 type ( pin 1: signal ground, pin 2: hot ?+?, pin 3: cold ?-? ) Output Electronically balanced and floating simulating transformer output with app. 50 kOhm/560pF to ground impedance for each leg RF suppresion with LC filters Impedance 50 Ohms (each leg) Max level +20 dBm into 600 Ohms Output symmetry balance > 65dB (20Hz-20KHz IEC) Connectors XLR-3 type ( pin 1: signal ground, pin 2: hot ?+?, pin 3: cold ?-? ) Performance frequency response +-0.5dB, 20Hz-20KHz (Eq switches out) THD 0.01%, 20Hz-20kHz Noise -90dBm (typ. -98dBm), 22Hz-22KHz graphic equaliser in circuit (0dB setting) Level control -infinite to +6dB Overload indicator lights for approximately 200ms if the instaneous peak voltage (+ or -) at any point in the equaliser comes within 1dB of clipping Filters Graphic equaliser: 30 ISO center frequencies 25Hz-20KHz in 1/3 octave steps Center frequency tolerance +-1% Q tolerance +-1% Max boost/cut 12dB Switchable in/out signal path High pass filter: Frequency Fixed 30Hz Type maximally flat 18dB/octave Switchable slople 6/12dB/octave Power Requirements Voltage 110/120/220/240V 50/60Hz Consumption 20VA IEC type connector Size and weigth Size 482mm (19inch) wide x 133mm high x 200mm deep Weight app. 6kg |
1215 Dual 15-Band Graphic Equalizer
The dbx 12 Series were designed to meet the needs of the most
demanding sound reinforcement environments, while offering the
simplicity of straightforward controls. The 1215 provides standard
features like dual channels, 15 2/3 octave bands, ISO frequency
centers, +/-12 dB input gain range, and switchable 40Hz/18 dB per
octave low-cut filters, but also includes other thoughtful features.
These include 45 mm faders; selectable +/-6dB or +/-15dB boost/cut
range for precise gain adjustments; XLR, barrier strip, and 1/4'' TRS
connectors for installation ease; balanced inputs and outputs for quiet
operation; and chassis/signal ground lift capabilities for quick hum isolation.
The visionary design of the dbx 12 Series makes your job easier.
The dbx 12 Series Equalizers were precision engineered to provide years
of maintenance-free operation in any application. The magnetically isolated
transformer, electronically balanced/unbalanced inputs and servo balanced/
unbalanced outputs, RF-filtered inputs and outputs, and power-off hard-wire
relay bypass with 2 second power up delay were steps our engineers took
to ensure compatibility for all installations. Only the best components were
utilized, yielding a 10Hz to 50kHz frequency response, greater than 90dB SNR
(ref +4dBu), less than 0.005% THD +Noise (1kHz at +4dBu), and interchannel
crosstalk of less than -80dB from 20Hz to 20kHz. All this attention to detail
is contained in a 2U steel/aluminum chassis.
- Switchable boost/cut ranges of ±6 or ±15 dB
- Electronically balanced/unbalanced inputs
- Servo balanced/unbalanced inputs
- RF filtered inputs and outputs
- XLR, Barrier Strip, and 1/4" TRS connectors
- -12dB/+12dB input gain range
- 18dB/octave 40Hz Bessel low-cut filter
- Chassis/signal ground lift capability
- Internal power supply transformer
- Power-off hardwire relay bypass with 2-second power-up delay
|
- Audiophile 31-band stereo graphic equalizer for live and studio applications
- Revolutionary FBQ Feedback Detection system instantly reveals critical frequencies and can also be used as audio analyzer
- Ultra-low noise 4580 operational amplifiers for highest signal integrity
- Dedicated Limiters with gain reduction meters for each channel protect your sound system from overload and distortion
- Pink noise generator provides test signals to adapt your sound system to any room acoustics
- Mono subwoofer output with dedicated level control and adjustable crossover frequency
- Additional sweepable high and low-cut filters for each channel remove unwanted frequencies e.g. floor rumble, hiss etc.
- Highly accurate 8-segment LED input/output metering and input gain controls for easy level setting
- Relay-controlled hard bypass with an auto-bypass function during power failure (fail-safe relay)
- Servo-balanced inputs and outputs with 1/4" TRS and gold-plated XLR connectors
- “Planet Earth" switching power supply for maximum flexibility (100
- 240 V~), noise-free audio, superior transient response plus low power consumption for energy saving
| INPUT
Connectors: 1/4" TRS, female XLR (pin 2 hot)
Type: Electronically balanced/unbalanced, RF filtered
Impedance: Balanced 40k ohm, unbalanced 20k ohm
Max Input Level: >+21dBu balanced or unbalanced
CMRR: >40dB, typically >55dB at 1kHz
OUTPUTS
Connectors: 1/4" TRS, male XLR (pin 2 hot)
Type: Impedance-balanaced/unbalanced, RF filtered
Impedance: Balanced 100 ohm, unbalanced 50 ohm
Max Output Level: >+21dBu balanced/unbalanced into 2k ohm or greater
>+18dBm balanced/unbalanced (into 600 ohm)
SYSTEM PERFORMANCE
Bandwidth: 20Hz to 20kHz, +0.5/-1dB
Frequency Response: 50kHz, +0.5/-3dB
Dynamic Range: Typicall >112dB
Signal-to-Noise: Typically >95dB
THD+Noise: |
* 2 channel 15 2/3 octave band graphic equalizer
* 25Hz - 16kHz frequency control * Constant Q circuitry
(3% frequency accuracy) * Selectable 6dB or 12dB control
* Variable level control * By-pass switch * Overload threshold LED (5dB below clipping) * Ground lift switch * XLR & 1/4" TRS balanced Inputs/Outputs * Power: Selectable 120V/220V voltage
* Dimensions: 1.75" H x 19" W x x 8.5" D / 44.5mm x 483mm x 216mm - 1 space r.m. * Weight: 4.5 lbs. / 2.5kg
XEQ-152 Specifactions:
* Input type: Active balanced / Unbalanced * Output Impedance: |
DBX 2215 Dual 15-Band Graphic Equalizer with Noise Reduction
It's amazing. One little button. So much effect. dbx? Type III? Noise Reduction is an entirely new concept... virtually instantaneous encode/decode within the circuitry of the box. We started out to build the finest EQs possible, boxes with the heritage and performance to rival our famous 30 Series EQs. And to no one's surprise they came out awfully darn good. (Ask to see the Audio Precision plots compared to the competition.) But then, Roger (our chief engineer, a nice guy, as far as engineers go) got the crazy idea of putting this new noise reduction stuff in the box. We listened to it and were amazed. The EQs sounded great without it but with it the performance was nothing short of incredible. Check it out yourself and see.
But hey, Roger wasn't about to stop there. PeakPlus? Limiter. Who knows more about limiting than the folks at dbx; nobody... that's who. So when the guys were developing this new series of EQs they wanted something that would be unique to these EQs. That's when Roger got another one of his bright ideas and said "I bet they'll work a lot better if there's a cool limiter built in." Next thing you know, all the guys are in the studio amazed at the new limiter Roger had designed specially for the 20 Series. Once again, hearing is believing... With a threshold range of 0dbu to plus 20dbu, the patent-pending PeakPlus limiter is designed to tame your program material from the subtlest nuances to the rowdiest hits. Also, the four stage LED ladder gives you a great visual indication as to what the limiter is doing.
20 Series EQs. You used to have to settle for second best in a reasonably priced EQ but not any more. With the new 20 Series from dbx Professional Products you get a great EQ circuit, a graceful yet powerful limiter and the revolutionary new design of the Type III Noise Reduction. Check out the dbx 20 Series graphic EQs at your pro audio outfitter. You'll see, with the 20 Series EQs you get MORE!!!
SPECIFICATIONS:
INPUT
|
Connectors:
|
1/4" TRS, female XLR (pin 2 hot), and barrier terminal strip
|
Type:
|
Electronically balanced/unbalanced, RF filtered
|
Impedance:
|
Balanced 40k ohm, unbalanced 20k ohm
|
Max Input Level:
|
>+21dBu balanced or unbalanced
|
CMRR:
|
>40dB, typically >55dB at 1kHz
|
OUTPUTS
|
Connectors:
|
1/4" TRS, male XLR (pin 2 hot), and barrier terminal strip
|
Type:
|
Impedance-balanaced/unbalanced, RF filtered
|
Impedance:
|
Balanced 200 ohm, unbalanced 100 ohm
|
Max Output Level:
|
>+21dBu balanced/unbalanced into 2k or greater
>+18dBm balanced/unbalanced (into 600)
|
SYSTEM PERFORMANCE
|
Bandwidth:
|
20Hz to 20kHz, +/-0.5dB
|
Frequency Response:
|
50kHz, +0.5/-3dB
|
Noise Reduction In:
|
(+/-6 and +/-15dB range):
|
Signal-to-Noise:
|
>102dB, unweighted, ref: +4dBu, 22kHz measurement bandwidth
|
Dynamic Range:
|
>120dB, unweighted
|
Noise Reduction Out:
|
(+/-6dB range):
|
Signal-to-Noise:
|
>94dB, unweighted, ref: +4dBu, 22kHz measurment bandwidth
|
Dynamic Range:
|
>112dB, unweighted
|
Noise Reduction Out:
|
(+/-15dB range):
|
Signal-to-Noise:
|
>90dB, unweighted, ref: +4dBu, 22kHz measurement bandwidth
|
Dynamic Range:
|
>108dB, unweighted
|
THD + Noise:
|
| |
Reviews
There are no reviews yet.