| Content |
The COM3 and COM6 are public adress amplifiers with a power of up to 60 W. They contain 2 unbalanced stereo line level inputs, which are switchable between Line and Mic level and one Microphone level Input. This way, a maximum of 3 balanced microphones can be connected.
The output level is selectable between high impedance 100 V, 70 V and 25 V outputs, or 4 Ohm low impedance. It is equipped with an advanced protection circuit, which protects against DC short ciruit, overheating, overload and limits the signal when necessary. All control functions such as individual channel volume controls, a 2 band tone control, the master volume control and indicators like a VU LED bar and clipping leds are located at the front of the amplifier.
Features- 2 stereo unbalanced inputs selectable between Mic / Line
- 1 Microphone Input
- 100 V / 70 V / 25 V high impedance outputs
- 4 Ohm low impedance output
- Telephone pager connection
- 2 band tone control
Specifications- Model Name / Type: COM3 / public adress amp
- RMS Power: 30 W
- Frequency Response: 80 Hz - 18 kHz
- THD+N:
- Signal / Noise: > 100 dB
- Output Voltage / Impedance: 100 V / 70 V / 25 V / 4 ohms
- Power Supply: 240 V AC / 50 - 60 Hz
- Dimensions (W x H x D): 270 x 76 x 230 mm
|
- Easy installation in practically any 12V battery equipped car.
- Compact, rugged construction and front panel controls.
- Two phone jack mic. inputs and handy phone jack AUX input for external equipment connection.
- Unidirectional dynamic microphone with talk switch.
| Specification |
|
|---|
| Power Source | Standard voltage: 14VDC
Usable Voltage; 10 ~ 16V DC (12V Battery Used) | | Power Consumption | 4.4A or less at rated power output. | | Output Power | Rated 30W, max. 60W | | Output Impedance | 4Ω (BRN), 8Ω (ORG), COmmon (WHT)
Changeable by changing lead wire connections. | | Distortion | Less than 5% (at 1kHz rated output) | | Frequency | Response 100 ~ 10,000Hz | | Input | Mic 1, 2 : 600Ω, 4 mV, Phone Jack
Aux : 10 kΩ, 500 mV, Phone Jack | | Dimensions | (W x H x D): 178 x 50 x 144mm (mounting device excluded) | | Weight | 1.1 kg | | Finish | Front panel; ABS resin, Black
Case; Zinc plated steel sheet | | Accessory | Microphone holder ... 1
Mounting Bracket ... 1
Mounting Screw ... 1
Fuse (8A) ... 1
Connection cord ... 1 set | | Accessory | Microphone Unidirectional dynamic type with Talk switch
Impedance : 600Ω
Sensitivity : -53dB (IkHz, 0 dB = 1 V / Pa) |
|
High cost-performance
Suitable for commercial audio systems in schools,
offices, shops, restaurants, factories, houses of worship, and large meeting rooms.
Equipped with balanced mic. inputs for better isolation from external noise, compared to unbalanced inputs.
Improved durability compared with conventional
TOA models.
Flexibility
A wide range of power outputs from 30W to 240W
Offers a comfortable acoustic space thanks to tone
control at bass and treble.
Both AC and DC operation possible
Phantom power provided to MIC1, for supplying
power to a condenser microphone.
Easy to handle
Scratch and fingerprint-resistant finish•Easy and quick volume control with master volume control.
| Specification |
|
|---|
| Power Source | 220 - 240V AC or 24V DC | | Rated Output | 30W | | Power Consumption | 34W (EN60065), 78W(AC operation at rated output, 2A (DC operation at rated output) | | Frequency Response | 50 - 20,000Hz (+/- 3 dB) | | Distortion | Under 1% at 1kHz,1/3 rated power | | Input | MIC 1: -60db 600Ω,electronically balanced, 5-P Din type. MIC 2,3:-60db 600Ω,electronically balanced, 5-P phone jack. AUX 1,2: -20dB, 10kΩ, unblanced, RCA pin jack. Mute: Contact Pin 4 - 5 Closure input (for MIC 1) | | Output | SPEAKER OUT:Balanced (floating)
HIGH IMPEDANCE:330W (100V)
LOW IMPEDANCE: 4Ω (11V)
REC. OUT: Odb, 600Ω unbalanced, RCA pin jack | | Phnatom Powe | DC + 21V (MIC 1) | | S/N Ratio | Over 60dB | | Tone Control | Bass: +/- 10 dB at 100k Hz Treble: +/- 10 dB at 10k Hz | | Muting | MIC1: Mutes other signals by 0 - 30 dB attenuation | | Indicator | Power signal, peak | | Finish | Panel: ABS resin, black/Case: Steel plate, black | | Dimensions | 420 (W) x 100.9 (H) x 280.2 (D) mm | | Weight | 5kg |
|
P-120D features 2x 200W into 4 Ohm load. This amplifier matches the needs for noiseless operation through air-cooling. It is ideally suitable in studios, small theatres, cabarets, churches, conference- and multimedia rooms etc. Multiple protection circuits care for stable operation. The amplifier is rackmountable (2 units). The optional transformer LT-101 converts the input to a balanced transformer isolated input. | - Easy installation in practically any 12V battery equipped car.
- Compact, rugged construction and front panel controls.
- Two phone jack mic. inputs and handy phone jack AUX input for external equipment connection.
- Unidirectional dynamic microphone with talk switch.
| Specification |
|
|---|
| Power Source | Standard voltage: 14VDC
Usable Voltage; 10 ~ 16V DC (12V Battery Used) | | Power Consumption | 2.2A or less at rated power output. | | Output Power | Rated 15W, max. 35W | | Output Impedance | 4Ω (BRN), 8Ω (ORG), COmmon (WHT)
Changeable by changing lead wire connections. | | Distortion | Less than 5% (at 1kHz rated output) | | Frequency Response | 100 ~ 10,000Hz | | Input | Mic 1, 2 : 600Ω, 4 mV, Phone Jack
Aux : 10 kΩ, 500 mV, Phone Jack | | Dimensions | (W x H x D): 178 x 50 x 132mm (mounting device excluded) | | Weight | 900g | | Finish | Front panel; ABS resin, Black
Case; Zinc plated steel sheet | | Accessory | Microphone holder ... 1
Mounting Bracket ... 1
Mounting Screw ... 1
Fuse (4A) ... 1
Connection cord ... 1 set | | Accessory | Microphone Unidirectional dynamic type with Talk switch
Impedance : 600Ω
Sensitivity : -53dB (IkHz, 0 dB = 1 V / Pa) |
|
High cost-performance
Suitable for commercial audio systems in schools,
offices, shops, restaurants, factories, houses of worship, and large meeting rooms.
Equipped with balanced mic. inputs for better isolation from external noise, compared to unbalanced inputs.
Improved durability compared with conventional
TOA models.
Flexibility
A wide range of power outputs from 30W to 240W
Offers a comfortable acoustic space thanks to tone
control at bass and treble.
Both AC and DC operation possible
Phantom power provided to MIC1, for supplying
power to a condenser microphone.
Easy to handle
Scratch and fingerprint-resistant finish•Easy and quick volume control with master volume control.
| Specification |
|
|---|
| Power Source | 220 - 240V AC or 24V DC | | Rated Output | 120W | | Power Consumption | 124W (EN60065), 260W(AC operation at rated output, 8A (DC operation at rated output) | | Frequency Response | 50 - 20,000Hz (+/- 3 dB) | | Distortion | Under 1% at 1kHz,1/3 rated power | | Input | MIC 1: -60db 600Ω,electronically balanced, 5-P Din type. MIC 2,3:-60db 600Ω,electronically balanced, 5-P phone jack. AUX 1,2: -20dB, 10kΩ, unblanced, RCA pin jack. Mute: Contact Pin 4 - 5 Closure input (for MIC 1) | | Output | SPEAKER OUT:Balanced (floating)
HIGH IMPEDANCE:83W (100V)
LOW IMPEDANCE: 4Ω (22V)
REC. OUT: Odb, 600Ω unbalanced, RCA pin jack | | Phnatom Powe | DC + 21V (MIC 1) | | S/N Ratio | Over 60dB | | Tone Control | Bass: +/- 10 dB at 100k Hz Treble: +/- 10 dB at 10k Hz | | Muting | MIC1: Mutes other signals by 0 - 30 dB attenuation | | Indicator | Power signal, peak | | Finish | Panel: ABS resin, black/Case: Steel plate, black | | Dimensions | 420 (W) x 100.9 (H) x 360.3 (D) mm | | Weight | 10kg |
|
Reviews
There are no reviews yet.