With added functionality and enhanced audio performance, the AR-133 has been designed to be more affordable for musicians, studios and PA companies. The unit includes phantom power and battery supplies as standard. Should the phantom power from the console fail or be accidentally switched off, the AR-133 automatically switches over to the internal 9V battery […]
With added functionality and enhanced audio performance, the AR-133 has been
designed to be more affordable for musicians, studios and PA companies.
The unit includes phantom power and battery supplies as standard. Should the
phantom power from the console fail or be accidentally switched off, the AR-133
automatically switches over to the internal 9V battery providing uninterrupted use.
The unit is housed in a rugged aluminium extrusion case, with robust polyurethane
end-cheeks which give the AR-133 a very distinctive look.
Input connectors are both 1/4″ jack sockets and an XLR socket, the latter meaning
that the AR-133 can be used to convert unbalanced signals to a balanced output on
XLRs throughout.
The arched case allows cables to run back underneath the unit from the end for neat
cable management.
Input attenuation is 0, -20 or -40dB, making the box suitable for instrument, line or
amplifier levels on inputs. On the output side, a ground-lift switch is provided for quick
solutions to ground-loop problems.
The AR-133 uses an enhanced version of the same audio path as the AR-116, now
regarded by many people as a reference standard. The sound quality is legendary,
particularly on acoustic and bass guitars.
Numerous applications can be satisfied by the AR-133. For example, as well as the
traditional guitar use, the AR-133 can be used with keyboards, DJ consoles, amplifier
outputs, and other electronic sources.An additional bonus is the ability to use the AR-133
as an active balancing device.
Input Section
Input Impedance 1M Ohm (pad at 0dB)
47k Ohm (pad at -20dB)
47k Ohm (pad at -40dB)
Max Input Level +9dBu (pad at 0dB)
+29dBu (pad at -20dB)
+49dBu (pad at -40dB)
Connectors Two Parallel 1/4″ jack connectors and a parallel
XLR connector (unbalanced)
Jack: Tip Hot (+ve)
Sleeve Ground
XLR: Pin 2 Hot (+ve)
Pin 1 & 3 Ground
Output Section
Output Transformer Balanced
Max. Output Level +8dBu into 600 Ohms or greater
Connector XLR3-32 or equivalent
System Performance
Distortion (THD) < 0.005% at 1khz, 0dbu output
Noise < -105db unweighted, 22hz-22khz, rms*
Frequency Response 30Hz to 20kHz, +0dB/-1dB
General
Main/Standby battery 9 volt PP3 type, preferably alkaline.
Current drain on phantom – less than 7.5mA
on battery – less than 2mA.
Phantom Power +20 volts DC to +48 volts DC
Weight 650 gms, excluding batteries.
Overall Dimensions 59 mm x 124 mm x 143 mm
(2.3″ x 4.9″ x 5.6“)
Weight
0.65 kg
Reviews
There are no reviews yet.
Be the first to review “BSS AR-133 ACTIVE DI BOX (Battery/ Phantom Powered)” Cancel reply
Professional and multi-purpose direct injection box for stage and studio applications
Provides impedance and signal matching for the direct connection of instruments to mixers and amplifiers
Ultra-flat frequency response due to renowned BEHRINGER OT-1 transformer
Internal battery automatically shuts off when phantom power is applied
Allows direct connection to speaker outputs with up to 3,000 Watts
Content
With added functionality and enhanced audio performance, the AR-133 has been
designed to be more affordable for musicians, studios and PA companies.
The unit includes phantom power and battery supplies as standard. Should the
phantom power from the console fail or be accidentally switched off, the AR-133
automatically switches over to the internal 9V battery providing uninterrupted use.
The unit is housed in a rugged aluminium extrusion case, with robust polyurethane
end-cheeks which give the AR-133 a very distinctive look.
Input connectors are both 1/4" jack sockets and an XLR socket, the latter meaning
that the AR-133 can be used to convert unbalanced signals to a balanced output on
XLRs throughout.
The arched case allows cables to run back underneath the unit from the end for neat
cable management.
Input attenuation is 0, -20 or -40dB, making the box suitable for instrument, line or
amplifier levels on inputs. On the output side, a ground-lift switch is provided for quick
solutions to ground-loop problems.
The AR-133 uses an enhanced version of the same audio path as the AR-116, now
regarded by many people as a reference standard. The sound quality is legendary,
particularly on acoustic and bass guitars.
Numerous applications can be satisfied by the AR-133. For example, as well as the
traditional guitar use, the AR-133 can be used with keyboards, DJ consoles, amplifier
outputs, and other electronic sources.An additional bonus is the ability to use the AR-133
as an active balancing device.
Input Section
Input Impedance 1M Ohm (pad at 0dB)
47k Ohm (pad at -20dB)
47k Ohm (pad at -40dB)
Max Input Level +9dBu (pad at 0dB)
+29dBu (pad at -20dB)
+49dBu (pad at -40dB)
Connectors Two Parallel 1/4" jack connectors and a parallel
XLR connector (unbalanced)
Jack: Tip Hot (+ve)
Sleeve Ground
XLR: Pin 2 Hot (+ve)
Pin 1 & 3 Ground
Output Section
Output Transformer Balanced
Max. Output Level +8dBu into 600 Ohms or greater
Connector XLR3-32 or equivalent
System Performance
Distortion (THD) < 0.005% at 1khz, 0dbu output
Noise < -105db unweighted, 22hz-22khz, rms*
Frequency Response 30Hz to 20kHz, +0dB/-1dB
General
Main/Standby battery 9 volt PP3 type, preferably alkaline.
Current drain on phantom - less than 7.5mA
on battery - less than 2mA.
Phantom Power +20 volts DC to +48 volts DC
Weight 650 gms, excluding batteries.
Overall Dimensions 59 mm x 124 mm x 143 mm
(2.3" x 4.9" x 5.6“)
Product Features:
Professional and multi-purpose direct injection box for stage and studio applications
Provides impedance and signal matching for the direct connection of instruments to mixers and amplifiers
Ultra-flat frequency response due to renowned BEHRINGER OT-1 transformer
Internal battery automatically shuts off when phantom power is applied
Allows direct connection to speaker outputs with up to 3,000 Watts
Switchable input attenuation allows input levels of up to +50 dB
Ground Lift switch eliminates typical ground loop problems
¼" TRS and gold-plated XLR connectors
Ultra-rugged, road-suitable aluminum case
Stackable oversized rubber corners
High-quality components and exceptionally rugged construction ensure long life and durability
Conceived and designed by BEHRINGER Germany
With the DI100, you can rest assured that your sound source will reach the console balanced and noise-free. BEHRINGER's take on the all-important active DI box gives you functionality, durability and incredible sound at a remarkable price.
Be Direct
Plug into the DI100's balanced 1/4" TRS or XLR input, then send a signal to your console via the balanced XLR output. You can even plug your guitar or bass amp's speaker output into the DI100, which can handle ratings of up to 3,000 Watts and still deliver a perfect signal. It also features a 1/4" LINK jack to send your signal to an on-stage amplifier. The DI100 also has a switchable attenuation pad, allowing input levels of up to +50 dB. There is also a ground lift switch to eliminate noise associated with ground loops. The DI100 also features BEHRINGER's renowned OT-1 output transformer.
Superior Sound, Incredible Value
DI boxes are an essential part of any stage or studio, and the DI100 delivers the exceptional sound you expect, wrapped up in a rugged, road-proof aluminum case with stackable rubber corners.
Tube-buffered DI-Box DI-1000
The Tube-Buffered DI-Box DI-1000 allows the extraction of all the musical details of musical interfaces without degrading the sound. This can only be achieved by providing a very high input impedance to avoid any loading of instrument pickups.This design approach allows seemingly infinite headroom to preserve the real dynamic range of the interfaced instruments.A vacuum tube enables all these goals to be achieved without any compromises in sound quality.The sonic difference between a standard DI-Box and the Tube-Buffered DI-Box is comparable to the musical resolution difference between a standard microphone and a studio microphone.One of the best transformers, the very transparent sounding JENSEN JT-DB-E, was chosen providing complete ground isolation. The parameters of this transformer, like frequency response, phase response, group delay and geadroom capabilities, play a vital part in the performance of this DI-Box.
Technical Specifications Input The signal of the instrument is directly fed to the tube circuit with > 20 MOhms input impedance to prevent any signal degradation, inevitable in traditional designs. Buffered Output“ The second stage of the vacuum tube is used to buffer the signal and lower the output impedance to < 8 kOhms. This unity gain output allows for cable runs of 10 meters without loosing high frequency information. Boost circuit The boost circuit increases the signal send to the output transformer by 15 dB. This may be useful for instruments with extremely low output, but decreases headroom capability to 6 Volt rms. Under these circumstances the signal may be clipped, concerning the output transformer?s signal, which gives you 2nd harmonic tube-like distortion. This distortion normally does not occur - but is sometimes desirable, being the reason for this special feature. Unity circuit The unity circuit feeds a low distortion unity gain signal to the JENSEN output transformer. This gives the best possible sound quality. Ground-lift“-Switch This front panel mounted switch allows complete ground and electrical isolation between the direct injection box and the console or recording device.
Mechanical Specifications Cabinet 2 mm stainless steel Front- and rear-panel 1,5 mm stainless steel lasercut and photo-chemically etched Dimensions 185 x 100 x 40 mm Vibration insulation 4 high-compliance rubber-elements Operating Voltage 220/110 V AC, selectable via rear panel mounted switch. The fuse is easily accessible from the rear panel. IEC mains connector with optional fixture. Construction details Double sided glass fibre contacted PCB with 70 mm copper plating. 1% metal film resistors and the finest polypropylene capacitors are used in the signal path. MIL type Switchcraft jacks and high performance switches ensure flawless operation. The power supply is optimised via measurement quality toroid transformer and a low impedance design to ensure the lowest possible noise. Through a double sided PCB all parts are roadworthy secured. A waterclear blue LED perfects the aesthetics of the DI box.
Technical Data Input impedance > 20 MOhm Output impedance180 Ohm at 1 kHz Frequncy response 20 Hz - 20 kHz (-0,1 dB) 5 Hz - 120 kHz (-3 dB) THD at 0 dBv 0,06% at 20 Hz 0,04% at 1 kHz 0,035% at 20 kHz Signal to Noise Ratio 86 dB Tube ECC 83/7025 A - military E 83 CC optional Output transformer JENSEN JT-DB-E Polarity Pin 2 Hot , AES/IEC -Standard Max. Input voltage > 30 V peak
User´s Manual
LD Systems LDI02
DI Box active
Active DI box in a sturdy metal housing (aluminium/steel) with protective corners, silver-blue metallic, internal battery (9 V flashes during operation) is switched off automatically when phantom power is used (LED permanently illuminated),
extremely low battery consumption. Battery: 9 V block (not included).
Product type DI Boxes
Channels 1
Inputs 2
Input connectors 6.3 mm Jack , XLR
Max. input level + 10 / + 30 dBu dBu
Input impedance 1 M Ohm(s)
Outputs 1
THRU outputs/channel 1
Output connectors XLR
Frequency response 20 - 20.000 Hz
THDIndicators Power
Controls ground lift , Power
Operating voltage +48 V phantom power , 9 V block
Cabinet material metal
Cabinet surface painted
Width 135 mm
Depth 128 mm
Height 53 mm
Weight 0,645 kg
Passive DI box. Jack input with paralell "THRU" output, transformer balanced XLR output. Attenuable input sensitivity, can handle both line level and speaker level signals.
Product type
DI Boxes
Type
passive
Channels
1
Inputs
1
Input connectors
6.3 mm Jack
Max. input level
+ 54 dBu
Input impedance
(@ 60 Hz) 60k Ohm(s)
Input pad
0 / -30 dB
Outputs
1
THRU outputs/channel
1
Output connectors
6.3 mm Jack , XLR
Max. output level
+ 4 dBu
Output impedance
600 Ohm(s)
Frequency response
20 - 20000 Hz
Transformer balanced
yes
Ratio
10 : 1
Controls
attenuator , ground lift
Cabinet material
sheet steel
Cabinet surface
powder coated
Width
110 mm
Depth
73 mm
Height
42 mm
Weight
0,34 kg
Behringer DI-600P High-Performance Passive Direct Injection Box
Introducing the Ultra-Compact DI-Boxes from BEHRINGER
There are times when you will want to connect certain sound sources straight to other audio gear, be it for a live performance or a studio session. A direct connection between audio equipment can be a challenge though: technical problems crop up that?ll corrupt the signal.
The DI600P lets you connect instruments or amplifier outputs of up to 3,000 Watts. It converts any unbalanced signal to a balanced signal and eliminates unwanted noise. With its high-performance transformer, it also allows you to use very long cables without the loss of high frequencies.
This is the sort of medicine that?ll cure headaches in your studio or on stage.
It often happens that you want to connect certain sound sources straight to other audio gear, be it for a live performance or a studio session. The direct connection between audio equipment can quickly turn out to be a real challenge: technical problems crop up that can affect the signal.
Hook Your Guitar or Amp Up to the PA
Be ready for your next gig with the Behringer Ultra-DI DI600P direct box. Designed to send instrument or amplifier signals to the main mixing board, the DI600P is a high-performance passive DI is a useful tool in any gig rig or studio. Dual 1/4" TS jacks are wired in parallel let you plug your instrument into one and use the other as an output to your amp. The balanced XLR mic-level output feeds your mixer a clean and super-flat signal that is true to the source. Sweetwater knows that grounding issues and hum can be a problem at live gigs. The DI600P sports a ground lift switch to kill unwanted ground loops and hum. It also has a filter switch for optimal guitar tone and an instrument/amp switch with a 30dB input level drop. The Behringer Ultra-DI DI600P direct box is an extremely useful tool for any stage rig!
Behringer Ultra-DI DI600P Direct Box Features:
Compact, high-performance passive direct box
Jack input 1/4" TS in and parallel out
Gold-plated XLR output / impedance balanced
Super-flat frequency output for uncolored sound
Switchable filter that optimizes the DI for guitars
Instrument/Amp switch lowers the input level 30dB for feeding amplifiers into the DI
Instruments or amplifier outputs with up to 3,000 watts can be connected directly
Offers impedance and signal matching of instruments to mixers
This website uses cookies to improve your experience. We'll assume you're ok with this, but you can opt-out if you wish. Cookie settingsACCEPT
Privacy & Cookies Policy
Πολιτική χρήσης
Αυτός ο ιστότοπος χρησιμοποιεί cookies για να βελτιώσει την εμπειρία σας ενώ περιηγείστε στον ιστότοπο. Από αυτά τα cookies, κάποια cookie κατηγοριοποιούνται ως απαραίτητα να αποθηκεύονται στο πρόγραμμα περιήγησης σας, καθώς είναι απαραίτητα για τη λειτουργία βασικών λειτουργιών του ιστότοπου. Χρησιμοποιούμε επίσης cookies τρίτων που μας βοηθούν να αναλύσουμε και να κατανοήσουμε πώς χρησιμοποιείτε αυτόν τον ιστότοπο. Αυτά τα cookies θα αποθηκευτούν στο πρόγραμμα περιήγησης σας μόνο με τη συγκατάθεσή σας. Έχετε επίσης την επιλογή να εξαιρεθείτε από αυτά τα cookies. Ωστόσο, η εξαίρεση από ορισμένα από αυτά τα cookie μπορεί να επηρεάσει την εμπειρία περιήγησης σας.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.
Reviews
There are no reviews yet.