BSS BLU-320 I/O Expander with Digital Audio Bus and CobraNet

The Soundweb London BLU-320 offers configurable I/O, CobraNet audio, and a high bandwidth, fault tolerant digital audio bus.

The BLU-320 is configurable through HiQnet™ London Architect. A rich palette of logic objects and a "drag and drop” method of configuration provide a simple and familiar design environment.

This processor features CobraNet audio with primary and secondary ports for fault tolerance. Control is through a separate Ethernet port which allows CobraNet and control networks to be easily separated or mixed depending upon requirements.

The BLU-320 also features a low latency, fault tolerant digital audio bus of 256 channels which uses standard Category 5e cabling giving a distance of 100m between compatible devices. Fiber optic media converters can be used to increase the distance between devices to over 40km.

Four card slots which accommodate analog inputs, analog outputs, digital inputs and digital outputs in banks of four facilitate many different device I/O configurations.

Analog Input Cards provide software configurable gain in 6dB steps up to +48dB per channel and software selectable Phantom Power per channel. Digital Input Cards and Digital Output Cards process AES/EBU and/or S/PDIF audio and offer a variety of clocking and syncing options. (Further information about the I/O cards can be found on dedicated datasheets)

Phantom Power, Sync, Signal Present and Clip information per channel is easily accessible, without the requirement for a PC, from clear front panel LED indication. Device-specific information such as Device Name, Device Type, Firmware Version Number, Time, IP Address and Subnet Mask is available from the front panel display. A bi-directional locate function allows devices to be identified both from and within HiQnet London Architect.

12 Control Inputs and 6 Logic Outputs allow the BLU-320 to be integrated with GPIO compatible devices. The

Soundweb London Interface Kit, comprehensive documentation which details how Soundweb London systems can be integrated with third party control systems, is included within the installation of HiQnet London Architect.

The BLU-320 and the other members of the Soundweb London family provide the building blocks of the perfectly tailored system solution.

KEY FEATURES:

• Four Input / Output Card Slots


• Configurable Inputs / Outputs


• Analog Inputs (with Phantom Power per Channel)


• Analog Outputs


• Digital Inputs (AES/EBU and S/PDIF)


• Digital Outputs (AES/EBU and S/PDIF)


• Rich Palette of Logic Objects


• CobraNet Audio


• 256 Channel, Low Latency, Fault Tolerant Digital Audio Bus


• Clear Front Panel LED Indication


• Informative Front Panel Display


• Bi-Directional Locate Functionality


• 12 Control Inputs and 6 Logic Outputs for GPIO Integration


• Soundweb London Interface Kit for Third Party Control System Integration (Documentation)


• HiQnet Device


• Configuration, Control and Monitoring from HiQnet London Architect

With 12 inputs and 6 outputs and Ethernet control the dbx ZonePro? 1260 and 1261
are the newest members of the ZonePro? family providing a complete suite of signal
processing and control for Commercial Audio applications.
Designed to offer superior system sonic performance and flexibility, the 1260/1261 deliver
the highest quality tools available. Even the input and outputs connectors were chosen for
their standard usage and reliability. The ZonePro products offer Euroblock connectors for
balanced signals and RCA connectors for interfacing with consumer equipment often used
in commercial applications; there is also a simple analog input buss that allows inputs to be
sent from one unit to the next for unit and job scalability. The 1260 and 1261 provide every
necessary processing tool, from the input processing like gain control and EQ available on all
inputs to highly sophisticated and specific functions such as selectable paging microphone
processing including Gating, De-Essing, Auto Gain Control, Compression and Feedback
Suppression. The heart of the ZonePro products is the Routing module that provides of course
Primary Source Selection but also Source Ducking for Paging and Priority Override. The outputs
also offer a wealth of processing designed for commercial applications like our patent-pending
AutoWarmth? function that was co-developed with JBL to provide natural low frequency extension
at any signal level. Each output also offers EQ, Bandpass and Crossover filters, Limiting and Delay
for system optimization. With the ZonePro? every tool is at your disposal to maximize the response
of your system.
Beyond processing, the ZonePro? products offer multiple forms of control to further extend the
versatility of your system. From easy-to-use wall panel Zone Controllers for standard end-user
functions like source select and volume control to advanced system control including a built-in
Real Time Clock that can provide programmable system changes throughout the day or week.
For system setup and monitoring the ZonePro Designer software provides an intuitive interface
and a speedy setup Wizard for configuring and editing all system parameters. The addition of
Ethernet control means that not only will it work with standard network equipment, but it can also
be accessed from remote dialup locations or from wireless access points.
The ZonePro? 1260 and 1261 will take your Commercial Audio system to the next level with advanced
processing, versatility and control.
 
? Advanced Feedback Suppression (AFS?)
? Autowarmth?
? Auto Gain Control
? Compression
? Limiting
? Noise Gating
? Notch Filtering
? Bandpass and Crossover Filters
? Parametric EQ
? Security Lockout
? Wall Panel Control
? RS-232 Control
? IEC, UL and CSA Approvals
 
ZonePro? 1260/1261 Specifications    
      
ANALOG INPUT
Number of Inputs:
12 Total (2) Switchable mic or line, (8) RCA, and (1)
S/PDIF
Connectors:
Euroblock (Line and Mic) RCA (Source)
Type:
Impedance (Euroblock):
> 50kΩ Balanced, >25kΩ Unbalanced, RF Filtered
Impedance (RCA):
>25kΩ Unbalanced, RF Filtered
Max input line level:
+20dBu Mic/Line, +12dBu RCA
CMRR:
> 40dB, typically >55db @ 1kHz
Mic Pre gain:30 to 60dB
Mic EIN:
> 118dB, 22Hz-22kHz, 150Ω Source Impedance
Mic Phantom Power:
15V
 
ANALOG OUTPUTS
Number of Outputs 6
Connectors: Euroblock
Type:
Electronically balanced, RF filtered
Impedance:
120 ohms balanced, 60ohm unbalanced
Max Output Level: +20dBu
 
A/D PERFORMANCE
Type:
dbx Type IV? conversion system
Dynamic Range line:
>113 dB, A-weighted, >110 dB unweighted
Type IV dynamic range:
>119 dB, A-weighted, 22kHz BW
>117 dB, A-weighted, 22kHz BW
Sample Rate: 48kHz
 
D/A PERFORMANCE
Dynamic Range:
112 dB A-weighted, 109dB unweighted
 
SYSTEM PERFORMANCE
Dynamic Range:
>110 dB A-weighted, >107dB unweighted
THD+N:
0.003% typical at +4dBu, 1kHz, 0dB gain
Frequency Response:
20Hz - 20kHz, +/-0.5dB
Interchannel Crosstalk:
>80dB typical
Crosstalk input to output:
>80dB
Propagation Delay
0.6 msec
 
POWER REQUIREMENTS
Operating Voltage:
100-240 VAC, 50/60Hz
Power Consumption:
27 Watts
 
Physical:
Weight:
6.8 lbs.(3.1 kg) Shipping weight 8.8 lbs. (4.0 kg)
Dimensions:
1.75? H x 5.75? D x 19? W

Full-featured Speaker Processing in a 1U Space
Speaker processing can be a complicated business requiring a substantial array of equipment, but the Yamaha SP2060 offers everything you need in a single rack space. This innovative 24-bit, 96-kHz digital speaker processor delivers excellent sound quality, an impressive variety of processing functions — gain, delay, PEQ, comp, crossover, limiter, and an all-pass filter for phase adjustment — and intuitive programming from Yamaha's DME Designer application running on a personal computer. It has two analog inputs and six analog outputs, plus two AES/EBU format digital inputs for connectivity with a broad range of systems. And if you use Yamaha Installation Series Speakers, all you need to do is select one of the many optimized presets provided for great sound with minimum measurement and setup time. The SP2060 is a compact, portable 1U unit that is ideal for live sound or installations.

The LD DPA260 is a 6-Channel 19" Speaker Processor for our VA-4, VA-8 and UNO-Array with plenty of useful setups for each system

• Type: DSP Controller for Line Array VA-4, VA-8 and UNO
• Model Name: DPA-260
• Description: 6-Channel 19" speaker processor, 32bit DSP, 24bit AD/DA (48 kHz) converter
• Inputs: 2 Channels Analog/Digital, L + R, Noise Gate, the inputs and outputs are freely assignable, that means you can assign any input to any output and vice versa
• Input EQ: 5 Band PEQ, Low Shelf and High Shelf Types available
• Crossover Range: 20 Hz - 20 kHz
• Outputs: 6 Channels, High/Low Pass Filter, Filtertype and dB available, 7 Band PEQ, Low Shelf and High Shelf Types available, Limiter with Threshold, Attack and Release Parameters
• Delay: Time or Meter available, Max. Delay up to 848 ms
• Phase Invert Function: USB Port, Full programmable Software included with 24 Memory Capacity for Presets
• Display: 2 × 16 character LCD with backlight
• Switch mode power supply: 90 V - 250 V
• Dimensions:    19" / 1U

Providing 48-bit filter algorithms, 24-bit AD/DA conversion and a dynamic range of 115 dB, the DSP 244 sets new standards for digital loudspeaker controllers and processors. The DSP 244 is an universal Digital Sound System Processor that provides 2 inputs and 4 outputs; plus internal summing of the inputs 1 and 2. Via matrix it is possible to assign the outputs to any input or to the sum of the inputs. It is further possible to establish the following configurations: Stereo or Dual 2-Way systems, 3-Way + Direct and 4-Way systems, each with Mono Subchannel, but also full range systems. High and low-pass filters are provided for the frequency crossover functions in all operation modes. The selection includes Linkwitz-Riley, Butterworth and Bessel type filters with switchable slopes between 6, 12, 18 and 24 dB/oct. A huge number of additional filters offers extremely flexible correction of the frequency response. Each input incorporates a 5-band equalizer, allowing to assign high and low-pass, high and low-shelving or parametric peak-dip filters to its individual filter sections. Next to the frequency crossover filters, four additional filters are employed in each output channel, which also can be set to work as high or low-pass, high or low-shelving filters, parametric peak-dip filters, or all-pass filters. Additional filtering is provided through 2. order high-passes for the realization of B-6 alignment, or special LPN-filters (Low-Pass Notch filters) for correcting the frequency and phase responses of optimally vented woofer cabinets. Each channel additionally provides a delay, a polarity switch, a programmable level control and a digital compressor / limiter while the master delays are located in the input channels. Datasheets / ManualsBrochure (309KB)

Mains voltage 90 - 250 V AC / 50 - 60 Hz Power consumption 20 watts Safety class I Inputs 2 x XLR IN, electronically balanced, transformer optional available 2 x XLR OUT (Direct Out) Input voltage (nominal) 1.55 V / + 6 dBu Max. input voltage 24.5 V / + 30 dBu Input impedance 20 kohms Common mode rejection > 40 dB AD-conversion 24-bit, Sigma-Delta, 128 times oversampling, linear phase Outputs 4 x XLR OUT, electronically balanced Output voltage (nominal) 1.55 V / + 6 dBu Max. output voltage 8.7 V / + 21 dBu Output impedance