| Content |
Specifications | Frequency Response (at 1 watt into 4 ohms, 20Hz - 20 kHz) |
+0/–1 dB
| | Signal to Noise Ratio (below rated 8-ohm power at 1 kHz, A-weighted) |
100 dB
| | Damping Factor (8 ohm): 20 Hz to 400 Hz |
> 500
| | Input Stage |
Input is electronically balanced and employs
precision 1% resistors
| | AC Line Current |
CDi 1000: 11.50A, CDi 2000: 11.93A, CDi 4000: 11.75A
At idle: Draws no more than 45 watts.
| | Crosstalk (below rated power) 20 Hz to 1 kHz |
> 70 dB
| | Input Impedance (nominal) |
20 kilohms balanced, 10 kilohms unbalanced
| Load impedance (note: safe with all types of loads)
Dual
Bridge mono |
2–8 ohms
4–16 ohms
| | Voltage Gain (at 1 kHz, 8 ohm rated output) |
CDi 1000: 30.5 dB, CDi 2000: 32.9 dB, CDi 4000: 34.2 dB
| | Sensitivity (at 8 ohm rated output) |
1.4V
| | Maximum Input Signal |
+22 dBu typical
| | Operating Temperature |
0° C to 40° C at 95% relative humidity (non-condensing)
| | AC Line Voltage and Frequency Configurations Available (± 10%) |
100V, 120V-240V, 50/60 Hz
| | Ventilation |
Flow-through ventilation from front to back
| | Cooling |
Heat sinks and proportional-speed fan
| | Dimensions: Width, Height, Depth (behind mounting surface) |
EIA Standard 19 in. W (EIA RS-310-B)
x 3.5 in. (8.9 cm) H x 12.25 in. (31.1cm) D
| | Net Weight, Shipping Weight |
19 lb (8.6kg), 22 lb (10.0 kg)
| |
Multi-purpose, multi-function mixer/power amplifiers specifically designed for maximum versatility and cost-effective high-performance are ideal units for any PA requirement in locations such as schools and offices and other intermediate size environments. A choice of different power outputs are offered as well as functions such as paging and dual zone coverage.
| Specification | |
|---|
| Power Source |
AC mains 50/60Hz, or 24V DC (M4 screw terminal) |
| Output |
120W |
| Power Consumption |
AC operation: 158W (rated output), 66W (EN60065)
24V DC operation: 7.0A (rated output), 2.8A (EN60065) |
| Frequency Response |
50 - 20,000Hz ±3dB |
| Distortion |
Under 2% at 1kHz, rated power |
| Input |
MIC 1: -60dB*, 600Ω, electronically-balanced, combined type of XLR-3-31 equivalent and phone jack DIN socket (5 pins)
MIC 2, 3: -60dB(*1), 600Ω, electronically-balanced, combined type of XLR-3-31 Equivalent and phone jack
AUX 1(MOH): -20dB*, 10kΩ, unbalanced RCA pin jack
AUX 2: -20dB(*1), 10kΩ, unbalanced, RCA pin jack
AUX 3: -20dB(*1), 10kΩ, unbalanced, RCA pin jack combined type of XLR-3-31 and phone jack
TEL(*2): -20dB*1, 10kΩ, electronically-balanced, M3 screw terminal |
| Output |
REC: 0dB(*1), 600Ω, unbalanced, RCA pin jack
LINE 1,2(*3): 0dB(*1), 600Ω, unbalanced, RCA pin jack
MOH: 0dB(*1), 600Ω transformer balanced, M3 screw terminal
SPEAKER SELECTOR:
2 zone, high impedance (100V line/83Ω), individual selector switch, M4 screw terminal
DIRECT SPEAKER OUT:
High impedance (100V line/83Ω),M4 screw terminal
Low impedance (4 - 16Ω), M4 screw terminal(Both Low and High impedance terminals cannot be used at the same time.) |
| Phantom Power |
ON or OFF for each MIC 1 - 3 with switch setting |
S/N ratio
(Band Pass: 20 - 20,000Hz) |
Over 100dB (Master volume: min)
Over 76dB (Master volume: max)
Over 60dB (MIC 1 - 3))
Over 76dB (AUX 1 - 3)
Over 90dB (TEL)
Over 96dB (EMERGENCY) |
| Control Input |
Bass: ±10dB at 100Hz, Treble: ±10dB at 10kHz
TEL: No-voltage make contact input, open voltage: 24V DC, short-circuit: under 5mA, M3 screw terminal
EMERGENCY (*4): No-voltage make contact input, open voltage: 24V DC, short-circuit: under 10mA, M3 screw terminal |
| Control Output |
Power remote: Open collector output, withstand voltage: 35V DC, control current: under 50mA, M3 screw terminal |
| Indicator |
5 point LED output level meter, Power indicator LED, Zone indicator LED, Emergency LED, TEL LED |
| Priority |
EMERGENCY: Overrides other inputs
TEL: Overrides other inputs except "EMERGENCY”, ON/OFF selectable with switch setting
MIC 1: Overrides other inputs except "EMERGENCY & TEL”, ON/OFF selectable with switch setting |
| Operating Temperature |
-10ºC - +40ºC |
| Finish |
Panel: ABS resin, black, hair line
Case: Steel plate, black |
| Dimensions |
420 (W) x 107.7 (H) x 367 (D)mm |
| Weight |
12.6kg |
| Accessory |
Power cord x 1,
Terminal block cover x 1,
Terminal block cover mounting screw x 2 |
| Option |
Rack mounting bracket: MB-25B,
Volume control cover: YA-920,
Input transformer: IT-453A |
| Note* |
(*1) 0dB = 1V
(*2) Can be transformer-balanced with the addition of optional IT-453A input transformer.
(*3) LINE 1 and LINE 2 outputs can be interlocked with ZONE 1 and ZONE 2 speaker selectors, respectively. (This function needs internal modification.)
(*4)Operation when activated can be selected from the following: Turning ON the unit\'s power (factory-preset) or OFF. (The OFF function needs internal modification.) |
|
- Easy installation in practically any 12V battery equipped car.
- Compact, rugged construction and front panel controls.
- Two phone jack mic. inputs and handy phone jack AUX input for external equipment connection.
- Unidirectional dynamic microphone with talk switch.
| Specification |
|
|---|
| Power Source | Standard voltage: 14VDC
Usable Voltage; 10 ~ 16V DC (12V Battery Used) | | Power Consumption | 4.4A or less at rated power output. | | Output Power | Rated 30W, max. 60W | | Output Impedance | 4Ω (BRN), 8Ω (ORG), COmmon (WHT)
Changeable by changing lead wire connections. | | Distortion | Less than 5% (at 1kHz rated output) | | Frequency | Response 100 ~ 10,000Hz | | Input | Mic 1, 2 : 600Ω, 4 mV, Phone Jack
Aux : 10 kΩ, 500 mV, Phone Jack | | Dimensions | (W x H x D): 178 x 50 x 144mm (mounting device excluded) | | Weight | 1.1 kg | | Finish | Front panel; ABS resin, Black
Case; Zinc plated steel sheet | | Accessory | Microphone holder ... 1
Mounting Bracket ... 1
Mounting Screw ... 1
Fuse (8A) ... 1
Connection cord ... 1 set | | Accessory | Microphone Unidirectional dynamic type with Talk switch
Impedance : 600Ω
Sensitivity : -53dB (IkHz, 0 dB = 1 V / Pa) |
|
| | - SPEAKER SELECT(5ZONE SPEAKER OUTPUT) Six speaker select switches enable you to select any combination of up to five speakers. - SELECTABLE PRIORITY MUTING Switchable audio signal priority for MIC Channels 1, siren, Chime and Telephone input over other input sources. - MONITOR SPEAKER You can monitor output signal by using the monitor speaker, and can control the monitor level on front panel by 3 step lever switch. - ANNOUNCEMENT CHIME Convenient four-tone chime for use with announcements. - REMOTE CONTROL INPUT Individual speaker zones can be selected and chime can be operated by wired remote control. - EM(EMERGENCY) When EM switch is pressed in emergencies, EM broadcasting stored in VOICE IC is outputted. - REMOTE POWER You can turn on/off amplifier by remote control. - INDIVIDUAL INPUT GAIN CONTROLS Rear-panel gain controls for each input channel for total control of individual levels. - MODULAR DESIGN Optional modules can be installed in multiple configurations for convenience and ease of use. Choose the PAM-CDA (Compact Disc), PAM-T (AM/FM Tuner) or PAM-D (Cassette Deck) modules to expand the PAM-510/520ʼs audio capabilities. ACCESSORIES One detachable AC power cord is provided for use with this product. | | | | | | | PAM-510 | PAM-520 | | Amplifier Section (Amp In@1kHz, 4Ω Load Output) | Rated Output Power (THD 1%) | 120W(RMS) | 240W(RMS) | | Speaker Zone 1~5 Output | 25W MAX | 50W MAX | | Input Sensitivity/Impedance | 1V/20kΩ | | S/N | Better than 85dB | | Frequency Response (at 1kHz Half Power Output, ±3dB) | 80Hz~18kHz | | Mic Input Section (Mic 1~4 In@1kHz, Preamp Out) | Input Sensitivity/Impedance | –60dBV/600Ω | | S/N | Better than 55dB | | Frequency Response (±3dB) | 120Hz~10kHz | | Tone Control (Bass:100Hz,Treble:10kHz) | ±12dB | | Phantom Power | +24VDC | | Line Input Section (Line 1~2 In@1kHz, Preamp Out) | Input Sensitivity/Impedance | –30dBV/10kΩ | | S/N | Better than 65dB | | Frequency Response (±3dB) | 80Hz~15kHz | | Tone Control (Bass:100Hz,Treble:10kHz) | ±12dB | | Remote Amp Section (Remote In@1kHz, Preamp Out) | Mic Input Sensitivity/Impedance | –60dBV/600Ω | | S/N | Better than 55dB | | Frequency Response (±3dB) | 120Hz~10kHz | | Tel In Section (Tel In@1kHz, Preamp Out) | Input Sensitivity/Impedance | 0.3V/600Ω(USA/Canada) | | 0.775V/600Ω(EC & Associated) | | S/N | Better than 65dB | | Frequency Response (±3dB) | 330Hz~3kHz | | Pre Amp Out(Mic 1~4, Line 1~2, Tel In, Remote In) | 0dBV/600Ω | | | T.H.D | Less than 0.5% | | Record Out | –10dBV/3kΩ | | Operating Temperature | –10°C~40°C | | Power Source | 100–120VAC or 220–240VAC; 50/60Hz, 24VDC | | Power Consumption (1/8 POWER) | 180W | 320W | | Weight | 17kg/37.6lb | 19kg/42lb | | Dimensions | 482(W) x 132(H) x 398(D)mm 19(W) x 5.2(H) x 15.7(D)in | | ※ Specifications and design subject to change without notice. | | | |
|
The TOA VM-3000 Series is a highly cost-effective combined emergency voice alarm system and public address system. The VM-3000 Series is ideal for small and medium-sized applications, such as shopping centres, retail stores, nursing homes, schools and fitness clubs. It incorporates such emergency voice alarm functions as continuous speaker line monitoring and a built-in voice alarm. This easy to install and set-up, all-in-one system also offers PA broadcasting, paging and BGM functions that operate with uncompromisingly high audio quality to ensure consistently high intelligibility. The VM-3000 Series is digitally audio processed and controlled, with full digital audio mixing and a built-in high-quality electronic voice message feature. The system may be set up directly using the controls and LCD display on the front panel, also enabling easy operation of the system. Operational versatility is further enhanced by a dedicated software configuration capability for entering and updating settings via a PC.
| Specification |
|
|---|
| Power Source | AC mains, 50/60 Hz DC: 24 V DC | | Power Consumption | 600W | | Rated Output | 240W | | Frequency Response | 50 – 20,000 Hz, ±3dB (at 1/3 rated output) | | Distortion | Under 0.8% (at rated output, 1kHz) | | Signal-to-Noise Ratio | Over 85dB | Audio Input/Output
Characteristic | Sampling frequency: 48kHz
A/D D/A CONVERTER: 24bit | | Input | Input 1 – 3 : -50 dB (MIC)/-10dB (LINE) (changeable) 600Ω, electronically balanced combined XLR connector (female)/phone jack
Input 4: -50 dB (MIC)/-10 dB (LINE) (changeable) 600Ω, electronically balanced plug in screw connector
BGM 1 – 2 : -10 dB, 10kΩ RCA pin jack
External AMP Input: 100V Line plug in screw connector | | Output | Speaker output 1 – 2 : max (240w) per output
Speaker output 3 - 6 : max (120w) per output
Total with in 240W
Plug-in screw connector
Direct output : Direct output from internal or external amplifier
Plug-in screw connector
Recording output BGM / Paging : 0dB, 10kΩ, RCA pin jack | | RM Link 1.2 in | 2 RJ45 female connector for connecting the RM-300MF/RM-200M
Remote Microphone.
Maximum distance: RM1.2 Total 800 m
Link cable: Category 5 Shielded Twisted-Pair straight cable (CAT5-STP) | | Network I/F | RJ45 female connector for switching hub or PC
10 BASE-T/100 BASE-TX Circuit (Selectable by automatic negotiation)
Maximum distance: 100m between this unit and a switching hub or PC
Link cable: Category 5 Shielded Twisted-Pair straight cable (CAT5-STP) | | VM Link | RJ45 female connector for connecting the VM-3240E or VM-3360E
Maximum distance : 800 m
Link cable: Category 5 Shielded Twisted-Pair straight cable (CAT5-STP) | | EXT PA Link | RJ45 female connector for connecting the VP-2241 or VP-2421
Maximum distance : 5 m
Link cable: Category 5 Shielded Twisted-Pair straight cable (CAT5-STP) | | General Control In: 1 – 8/Out: 1 – 8 | Plug-in screw connector
Input : No-Voltage make contact input, open voltage: 24V DC, short-circuit current: under 1 mA
Output : Isolated open collector output, withstand voltage: 30V DC, operating current: under 50 mA | | Emergency Control In: 1 – 6/Status out | RJ45 female connector
Input 1 – 5 : No-Voltage make contact input, open voltage : 24V DC, short-circuit current: under 2 mA
Connection resistance to make the function: Inactive; 9.4kΩ ±5%/Active; 4.7kΩ ±5%
Input 6: Isolated voltage input: Inactive; -24V ±20%/Active; +24V ±20%
Status out: Relay contact output, withstand voltage: 40V DC, operating current: 2 – 300mA | | ATT Control | Plug In connector, relay contact, 30V DC, 125V AC 5A (AC/DC) | Power In/Out
PS Out/DC Power In | M4 Screw terminal distance between barriers 11 mm
This connector for connecting the VX-2000DS only
DC 28V/20A (operating range: 20 - 40V DC) | | DC24V Output | 24V DC ±10% Maximum feeding current 0.4A | | DS Link | RJ45 female connector for connecting the VX-2000DS
Maximum distance: 5 m
Link cable: Category 5 Shielded Twisted-Pair straight cable (CAT5-STP) | | Dimensions | 482 (W) x 132.6 (H) x 460 (D)mm | | Weight | 18kg | | Option | Input transformer: IT-450 |
|
High cost-performance
Suitable for commercial audio systems in schools,
offices, shops, restaurants, factories, houses of worship, and large meeting rooms.
Equipped with balanced mic. inputs for better isolation from external noise, compared to unbalanced inputs.
Improved durability compared with conventional
TOA models.
Flexibility
A wide range of power outputs from 30W to 240W
Offers a comfortable acoustic space thanks to tone
control at bass and treble.
Both AC and DC operation possible
Phantom power provided to MIC1, for supplying
power to a condenser microphone.
Easy to handle
Scratch and fingerprint-resistant finish•Easy and quick volume control with master volume control.
| Specification |
|
|---|
| Power Source | 220 - 240V AC or 24V DC | | Rated Output | 240W | | Power Consumption | 238W (EN60065), 520W(AC operation at rated output, 15A (DC operation at rated output) | | Frequency Response | 50 - 20,000Hz (+/- 3 dB) | | Distortion | Under 1% at 1kHz,1/3 rated power | | Input | MIC 1: -60db 600Ω,electronically balanced, 5-P Din type. MIC 2,3:-60db 600Ω,electronically balanced, 5-P phone jack. AUX 1,2: -20dB, 10kΩ, unblanced, RCA pin jack. Mute: Contact Pin 4 - 5 Closure input (for MIC 1) | | Output | SPEAKER OUT:Balanced (floating)
HIGH IMPEDANCE:42W (100V)
LOW IMPEDANCE: 4Ω (31V)
REC. OUT: Odb, 600Ω unbalanced, RCA pin jack | | Phnatom Powe | DC + 21V (MIC 1) | | S/N Ratio | Over 60dB | | Tone Control | Bass: +/- 10 dB at 100k Hz Treble: +/- 10 dB at 10k Hz | | Muting | MIC1: Mutes other signals by 0 - 30 dB attenuation | | Indicator | Power signal, peak | | Finish | Panel: ABS resin, black/Case: Steel plate, black | | Dimensions | 420 (W) x 100.9 (H) x 360.3 (D) mm | | Weight | 13kg |
|
Reviews
There are no reviews yet.