| Content |
The DVX DM15 is a low-profi le stage monitor. Unobtrusive yet very muscular, it is designed for sound reinforcement applications that require powerful low-end performance without added subwoofers. It sports a high-performance 15" neodymium woofer and a 1.4" neodymium compression driver, coupled to an aluminum" CD horn. This combinationʼs response across the human voiceʼs full range is impressively assertive.
Paired with high-output digipro digital power amps in a bi-amped confi guration,
theDVX DM15belies its unobtrusive look with performance that is far from understated, delivering plenty of power to cover midsized to large stages.
|
- 1000w RMS, 2000w peak, power delivers clarity, punch and more than enough headroom for any
- performance or practice space
- Specially-voiced 12-inch woofer and high frequency compression driver deliver your drum sounds
- with precise, full response across the entire frequency range without any artificial colouration
- (2) XLR/TRS 1/4-inch combo inputs with independent volume controls and clip indicator
- XLR output to link another Strike Amp 12 or send your performance to another input device
- Lightweight and flexible tilt-back cabinet design that can also be pole-mounted
- Contour EQ switch to control your sound
- Ground-Lift switch eliminates unwanted noise
Specifications:
- Output: Power 2000W (peak, 1300LF + 700HF), 1000W (continuous RMS, 650LF + 350HF)
- Low-Frequency: 12.0” (305mm) low-frequency driver, 3.0” (76mm) high-temperature voice coil
- High-Frequency: 1.4” (35mm) voice coil, neodymium-magnet high-frequency driver with precision waveguide
- Crossover Frequency: 2.0KHz
- Maximum SPL: 131dB (peak), 128dB (continuous) (dB-SPL @ 1m)
- Frequency Response: 53Hz – 20kHz (+3dB)
- Frequency Range: 46Hz – 22kHz (-10dB)
- Horn Coverage 90o horizontal x 60o vertical (nominal)
- Equalisation: Contour switch with low- and high-frequency +3dB boost
Connectors:
- (2) XLR/TRS 1/4” (6.35mm) combo inputs
- (1) XLR link output
- (1) IEC power cable input
- Controls Power switch, (2) volume control knobs (1 per input), EQ contour switch, ground-lift switch
- Indicators: (2) power LEDs (1 front-panel, 1 rear-panel), clip limiter LED
- Protection: Electronic clip, thermal & transducer overdrive
- Input Voltage: 100V~, 110–120V~, 220–240V~; 50/60Hz (switchable)
- Fuse: 100–120V T10AL AC250V 220–240V T5AL AC250V
- Consumption: 800W
- Enclosure: Trapezoidal, injection-molded polypropylene enclosure with perforated steel grille
Dimensions: (width x depth x height) 605 x 354 x 350mm
Weight: 16.3kg |
StageSource™ is designed to be the worldʼs most versatile loudspeaker system for musicians. Using six powerful DSP-based Smart Speaker modes, the StageSource L3m output is optimized for a variety of performance scenarios including front-of-house PA, floor monitor, personal PA, keyboard backline, acoustic guitar backline, or with a multi-effects guitar processor as a high-performance electric guitar speaker system. Onboard accelerometer and pole mount sensors automatically detect the speakerʼs orientation and set the Smart Speaker mode accordingly.
The 1,400-watt, 3-way, tri-amped speaker system and a dual-braced tour-grade plywood enclosure combine to deliver astounding power and reliability. The innovative multi-function design enables the L3m to be the perfect loudspeaker in a wide variety of applications including floor or stage-stacked, pole-mounted, horizontal as a floor monitor, Virtual Tilt-back for instrument backline or flown with the integrated M10 suspension points for installation.
| Cabin Type: | Wooden, 3-way | | Monitor Use: | Yes | | Amplifier: | 1,400‐watt | | LF/MF, Woofer: | 2x10” | | HF, Horn: | 1” exit compression driver | | DSP Processor: | Yes | | Frequency Response: | 47 Hz to 18 kHz | | Dimensions: | 312 mmx861 mmx 312 mm | | Weight: | 26.1 kg | | Color: | Black |
| The self-powered KD12 is an uncompromising monitor and fullrange speaker - all-in-one. The KD12 delivers advanced sonic clarity and top performance. Whether as stage monitor, fullrange speaker, frontfill for larger stages or as delay speaker: The KD12 is the ideal allround solution for the up-market user.
Features
► High-class performance in ultra-lightweight design (14 kg only)
► 1.000 W Class D bi-amped power module
► Extensive DSP featuring with delay function (up to 100 m)
► IDSE© intelligent digital sound editor (on-board optimization)
► Single-encoder EASY CONTROL DSP interface
► DBL© dual-band limiters for independently stable performance
► User presets (5 user preset memories)
► Graphic backlit screen (with locking function)
► Two combo inputs (XLR/6.3 jack with MIC/LINE switches)
► Two high-resolution microphone pre-amplifiers (in MIC mode)
► Rugged, texture-painted plywood enclosure
► Sophisticated 12" coaxial transducer
► 90° x 90° beam angle (for advanced sound distribution) | LD Systems Stinger MON81AG2
The LD Stinger MON81AG2 is an especially compact active monitor with broad frequency response and a maximum sound-level pressure of 116dB for versatile use on stage.
The 8" coaxial speaker with an integral 1" HF driver attains a dispersion angle of 75°x75°, which is beneficial in multifaceted applications as a stage monitor. The coaxial configuration results in a very homogenous sound in the entire dispersion area plus very low susceptibility to feedback. The active monitor is driven by a Class AB power amplifier with an output power of 80W RMS; short-circuit protection and a limiter ensure dependable operation.
The signal is connected and looped through using an XLR/ jack combo socket and the XLR output. The rear connector panel is rounded out by a volume control, LED indicators, and the IEC power socket
The elegant bass-reflex housing made of 15mm multiplex is finished with a durable coating and has ergonomically milled handles and a metal grille to protect the speaker. The monitor angle is 35°.
Type: active
Woofer size: 8“
Woofer size: 203 mm
Woofer type: coaxial speaker
Woofer magnet: ferrite
Woofer brand: custom made
Woofer voice coil: 2
Woofer voice coil: 50.8 mm
HF driver size: 1“
HF driver size: 25.4 mm
HF driver magnet: ferrite
HF driver brand: custom made
HF driver voice coil: 1“
HF driver voice coil: 25.4 mm
Amplifier: Class A / B
Dispersion angle (H x V): 75° x 75°
Power output (RMS): 80 W
Power output (peak): 160 W
Frequency response: 90 Hz - 20 kHz
Crossover frequency: 2.400 Hz
SPL (1 W/1 m): 97 dB
Max. SPL (continuous): 111 dB
Max. SPL (peak): 116 dB
Protection: limiter, short-circuit
Controls: Volume, On / Off
Indicators: Power, Limit
Number of line inputs: 1
Line input connectors: XLR/ 6.3 mm jack (combo)
Number of line outputs: 1
Line output connectors: XLR
Power supply: transformer
Operating voltage: 230 V AC / 50-60 Hz
Cabinet material: 15 mm plywood
Cabinet type: bass reflex
Monitor angle: 35°
Width: 320 mm
Depth: 250 mm
Height: 361 mm
Features: Ergonomic insert handles |
The HD 12-A offers an extremely linear response and a precise, deep low frequency control. The 12” woofer guarantee a superior sound projection indoor and outdoor. It is the ideal speaker for main front of house in small PA systems, for high power monitoring and it is the best solution where higher power is required for various applications in larger venues.
APPLICATIONS
- • Live Sound
- • Rental
- • Portable PA
- • Stage Monitoring
- • Clubs
General Specs
1200 WATT PEAK, 600 WATT RMS
Digital Bi-amp
DSP Sound Processing
RCF Precision Transducers
130 dB MAX SPL
Acoustical Specs
Frequency Response -3 dB:45 Hz ÷ 20000 Hz
Max SPL:130 dB
Horizontal coverage angle:90°
Vertical coverage angle:60°
Compression Driver:1“, 1.7" voice coil
Woofer:12“, 2.5" voice coil
Inputs/Outputs
Input signal:bal/unbal
Input connectors:Jack-XLR male
Output connectors:XLR female
Input sensitivity:-2 dBu / + 4 dBu
Processor Section
Crossover frequencies:1600 Hz
Protections:thermal, RMS
Limiter:Fast limiter
Controls:Volume, EQ shape, Mic/line
Amplifier Specifications
Total power:1200 W PEAK
High frequencies:300 W PEAK
Low frequencies:900 W PEAK
Total power:600 W RMS
High frequencies:150 W RMS
Low frequencies:450 W RMS
Connections:VDE AC socket
Cabinet Specs
Cabinet Material:Composite PP
Hardware:1 x M10 top, 1 x M10 bottom, 3 x M6 bottom
Handles:1 top, 2 side
Pole Mount/Cap:Yes
Grille:Steel
Colour:Black
Size/Weight
Height:647/25.47 mm/inch
Width:380/14.96 mm/inch
Depth:380/14.96 mm/inch
Net Weight:18.3/40.34 kg/lbs |
Reviews
There are no reviews yet.