| Content |
The 481 and 482 are slave units which include all of the functionality and features of the 480 .
They both incorporate 4 inputs and 8 outputs with Euroblock connectors on the 481 and XLRs
on the 482. However, they do not include the front panel programming interface. All programming
functions can be performed through the 480, the 480R, or via the Windows GUI. An unlimited
number of slaves can be chained together.
Features:
4 Input and 8 Outputs with routing
31 band graphic or 9 band parametric equalizer on every input (pre-crossover)
Dual Real Time Audio Analyzers
Butterworth, Bessel or Linkwitz-Riley crossover filters
27 Different Crossover Configurations
Time Alignment and Transducer Alignment Delays
Compressor/Limiter on every output
Speaker Compensation EQ (post crossover)
Multi-level Security System
Separate House and Show EQ with individual lockout
Triple redundant back-up of all parameters when running network, 480R and PC GUI
TYPE IV? Conversion System
Electronically balanced/RF filtered Euroblock Inputs and Outputs
Proprietary RS-485 Control Network
RS-232 PC Interface for computer display and configuration |
The ARX EC-2 is a flexible yet affordable 24 dB per octave Phase Correct active crossovers.
It has 2 modes of operation; as either Stereo 2 way or a Mono 3 way units, with a switch on
the back panel selecting either mode.
Features
Ultra low noise circuitry
Totally phase aligned at crossover point
Switchable Dual Channel 2 way or Single Channel 3 way
Unique 'semi-fixed' crossover point
24dB per octave (Fourth Order) Linkwitz-Riley filters
Separate Summed Mono Output
Balanced Inputs and Outputs
Built in High Pass filters
Intuitive, 'user friendly' layout
Flawless performance in any audio environment
Tamper-Proof Crossover Points
The crossover points are determined internally by the value of 4 resistors per channel; changing
the resistor value changes the crossover point. This 'semi fixed' method avoids the pitfalls of
externally adjusted crossover points, making the crossover points tamper-proof once they are set.
Idle fingers can't fiddle with the crossover points and create havoc with the system!
As a handy guide, a list of common crossover points and their corresponding resistor values are
printed inside the unit's lid, and also set out in the Owner's Manual.
On the front panel are level controls for Low and High in dual channel 2 way mode, and Low, Mid
and High in single channel 3 way mode, with corresponding Outputs on the rear panel.
Balanced Inputs and Outputs
EC-2 has Balanced Inputs and Outputs, on XLR connectors.
The EC-2 also has an additional summed Mono Low output, for applications that need a Mono Low
feed (e.g. Left and Right full-range plus a single Sub Bass speaker).
High Pass Filter
There is also a preset 30 Hz HighPass filter to remove unwanted subsonics which can damage speakers
and waste amplifier power.
In addition, each output has up to +6 dB of gain available, to compensate for amplifiers and speakers of
differing sensitivities.
Universal AC Power
AC power range is a universal 100 to 120V or 220 to 240VAC, and is connected to the unit via a standard
IEC connector, with built-in fuse and voltage change switch.
Uncompromising Audio Quality
Innovative circuit design is pointless unless it delivers stunning sound quality, and here the EC-2 excels.
It has been designed for uncompromising audio quality, and to achieve this, Linkwitz Riley 24dB (Fourth
Order) state variable filters are used throughout, ensuring a smooth Phase Correct transition through the
crossover region.
From Stage Monitors to Studio Monitors, from Front of House to the Front room of your House, the ARX
EC-2 is a crossover that is suited to any application that requires flawless, transparent sound.
You'll never compromise on Quality when you choose ARX
T E C H N I C A L S P E C I F I C A T I O N S
Input Impedance Balanced 20 Kohms, Unbalanced 10 Kohms
Input Headroom + 21 dB
CMRR >45 dB, 20 Hz-20 KHz
Output Impedance Balanced 300 ohms, Unbalanced 150 ohms
Output Level (Max) + 21dB
Frequency Response 30Hz-20KHz +or- 0.5dB
Note: 30 Hz is a function of the High Pass filter
Signal to Noise ratio (Controls at Unity) -90 dB Unweighted, -93 dB 'A' weighted
Distortion 004% THD,0dB,1KHz
Dynamic Range 111 dB
Power Requirements 100/120 V AC, 220/240 V AC
Weight 5 lbs/2.2 Kg
Dimensions 19“W x 13/4“H x 6“D, 482 x 44 x 155mm
Input Connector type XLR
Output Connector type XLR
Crossover point frequencies are changed internally by varying the value of 4 resistors
per channel.
Front Panel Controls
Low and High Output controls for 2 way mode
Low, Mid and High Output controls for 3 way mode
Marker panels for labelling crossover assigns
2 way/ 3 way status LEDs
Rear Panel
Balanced XLR Inputs and Outputs
Additional summed mono Low output
2 way / 3 way mode switch |
| Power supply: |
100-240 V AC, 50/60 Hz
6 V DC 800 mA |
| Power connection: |
Mains input via Coaxial power connector (M) mounting version power supply cord with AC adapter (provided) |
| Frequency range: |
10 - 30000 Hz |
| THD: |
<0,005 % at 1 kHz |
| DSP: |
Digital signal processor |
| Impedance: |
Input: 10 kOhm
Output: 50 Ohm |
| Gain: |
Output: -50 dB to +12 dB |
| Filter: |
Linkwitz-Riley; Butterworth; Bessel; 6db/oct; 12db/oct; 18db/oct; 24db/oct |
| Delay: |
0 - 5 ms |
| Dynamic range: |
Input: 114 dB
Output: 110 dB |
| Sample rate: |
67 kHz |
| Connections: |
Input: line via 2 x 3-pin XLR
Output: line via 6 x 3-pin XLR |
| Crossover frequency: |
20-20000 Hz |
| Max. level: |
Input: +22 dBu
Output: +9 dBu |
| USB port: |
Typ B |
| PC connect: |
DXO Software via USB, firmware can be updated |
| Housing design: |
(19") 48.3 cm rack installation 1 U |
| Dimensions: |
Width: 48,3 cm
Depth: 12,8 cm
Height: 4,45 cm |
| Weight: |
1,77 kg |
| Operating system: |
Win XP, Win Vista, Win 7, Win 10, OS X 10,5 or better |
|
With 6 inputs and 4 outputs the dbx ZonePro? 640 and 641 provide flexible signal routing,
powerful DSP processing and multiple control interfaces for Commercial Audio applications.
Designed to offer superior system sonic performance and flexibility, the 640/641 deliver the
highest quality tools available. Even the input and outputs connectors were chosen for their
standard usage and reliability. The ZonePro products offer Euroblock connectors for balanced
signals and RCA connectors for interfacing with consumer equipment often used in commercial
applications; there is also a simple analog input buss that allows inputs to be sent from one
unit to the next for unit and job scalability. The 640 and 641 provide every necessary processing
tool, from the input processing like gain control and EQ available on all inputs to highly sophisticated
and specific functions such as selectable paging microphone processing including Gating,
De-Essing, Auto Gain Control, Compression and Feedback Suppression. The heart of the
ZonePro products is the Routing module that provides of course Primary Source Selection
but also Source Ducking for Paging and Priority Override. The outputs also offer a wealth of
processing designed for commercial applications like our patent-pending AutoWarmth? function
that was co-developed with JBL to provide natural low frequency extension at any signal level.
Each output also offers EQ, Bandpass and Crossover filters, Limiting and Delay for system
optimization. With the ZonePro? every tool is at your disposal to maximize the response of
your system.
Beyond processing, the ZonePro? products offer multiple forms of control to further extend the
versatility of your system. From easy-to-use wall panel Zone Controllers for standard end-user
functions like source select and volume control to advanced system control including a built-in
Real Time Clock that can provide programmable system changes throughout the day or week.
For system setup and monitoring the ZonePro Designer software provides an intuitive interface
and a speedy setup Wizard for configuring and editing all system parameters.
The ZonePro? 640 and 641 will take your Commercial Audio system to the next level with advanced
processing, versatility and control.
? Advanced Feedback Suppression (AFS?)
? Autowarmth?
? Auto Gain Control
? Compression
? Limiting
? Noise Gating
? Notch Filtering
? Bandpass and Crossover Filters
? Parametric EQ
? Security Lockout
? Wall Panel Control
? RS-232 Control
? Windows? 2000 and XP GUI
? IEC, UL and CSA Approvals
| The DriveRack® PA2 provides all the processing you need between your mixer and amplifiers to optimize and protect your loudspeakers. With the latest advancements in dbx's proprietary AutoEQTM and AFSTM algorithms, a new input delay module for delaying the FOH system to the backline, Ethernet control via an Android®, iOS®, Mac®, or Windows® device, and updated Wizards, the DriveRack PA2 continues the DriveRack legacy of great-sounding, powerful, and affordable loudspeaker management processors, for a whole new generation.
Available Input Processing
- dbx Compression
- AFSTM (Advanced Feedback Suppression)
- Graphic EQ
- 8-Band Parametric EQ (adjusted when using the AutoEQ)
- Subharmonic Synthesis
Available Output Processing
- Crossover (supports full range, 2-way, and 3-way systems)
- 8-Band Parametric EQs (used for speaker tunings)
- dbx Limiting
- Driver Alignment Delays
| Input |
(2) line inputs. (1) RTA Mic input |
| Input Connectors |
(2) Female XLR line inputs. (1) Female XLR RTA Mic input |
| Input Type |
Electronically balanced/RF filtered |
| Input Impedance |
>50 kohm |
| A/D Converter |
dbx Type IVTM Conversion System |
| CMRR |
> 45dB |
| Mic Preamp Phantom Power |
+15VDC (RTA) |
| Mic Preamp Equivalent Input Noise (EIN) |
|
| Output |
(6) Line Outputs |
| Output Connectors |
Male XLR |
| Output Type |
Electronically balanced, RF filtered |
| Output Impedance |
120 Ω |
| Max Output |
+20dBu |
| A/D Dynamic Range |
112 dB A-weighted, 110 dB unweighted |
| Type IV Dynamic Range |
123 dB with transient material, A-weighted, 22kHz BW; 121 dB with transient material, unweighted, 22kHz BW; 115 dB typical with program material, A-weighted, 22kHz BW |
| Input Delay Length |
100ms |
| Alignment Delay |
10ms per channel (60ms total) |
| Sample Rate |
48kHz |
| Dynamic Range |
>110 dB A-weighted, >107dB unweighted |
| THD+Noise |
0.003% typical at +4dBu, 1kHz, 0dB input gain |
| Frequency Response |
20Hz - 20kHz, +/- 0.5dB |
| Interchannel Crosstalk |
|
| Operating Voltage |
100-120VAC 50/60 Hz - EU: 220-240 VAC 50/60 Hz |
| Power Consumption |
22 W |
| Unit Weight |
5.25 lbs. (2.4 kg) |
| Shipping Weight |
6.75 lbs. (3.1 kg) |
| Dimensions |
1.75" (H) x 5.75" (D) x 19" (W), 4.4cm (H) x 14.6cm (D) x 48.26cm (W) |
| D/A Dynamic Range |
112 dB A-weighted, 110dB unweighted |
|
Full-featured Speaker Processing in a 1U Space
Speaker processing can be a complicated business requiring a substantial array of equipment, but the Yamaha SP2060 offers everything you need in a single rack space. This innovative 24-bit, 96-kHz digital speaker processor delivers excellent sound quality, an impressive variety of processing functions — gain, delay, PEQ, comp, crossover, limiter, and an all-pass filter for phase adjustment — and intuitive programming from Yamaha's DME Designer application running on a personal computer. It has two analog inputs and six analog outputs, plus two AES/EBU format digital inputs for connectivity with a broad range of systems. And if you use Yamaha Installation Series Speakers, all you need to do is select one of the many optimized presets provided for great sound with minimum measurement and setup time. The SP2060 is a compact, portable 1U unit that is ideal for live sound or installations.
| Sampling Frequency | Internal Clock | 96kHz | | External Clock | Normal Rate | 44.1, 48kHz (±0.1%) | | Double Rate | 88.2, 96kHz (±0.1%) | | Signal Delay | 761µsec Input to Output, fs = 96kHz | | Frequency Response | 20Hz -40kHz (TYP 0dB, MAX +0.5dB, MIN -1.0dB), fs=96kHz, RL=600ohms | | Total Harmonic Distortion | 0.007% (+22dBu@1 kHz),
0.05% (+4dBµ@20 Hz - 40kHz)
fs=96kHz, RL=600ohms;
measured with 18dB/octave filter @80kHz | | Hum & Noise | TYP -82dBu,
fs=96kHz, RL=600ohms, Rs=150 ohms;
measured with 6dB/octave filter @12.7kHz;
equivalent to a 20kHz filter with ∞ dB/octave attenuation. | | Dynamic Range | 106dB AD+DA
fs=96kHz, RL=600ohms;
measured with 6dB/octave filter @12.7kHz;
equivalent to a 20kHz filter with ∞dB/octave attenuation. | | Crosstalk @1kHz | -80dB INPUT to Output
fs=96kHz, measured with 18dB/octave filter @80kHz | | Power Consumption | 30W | | Dimensions (W x H x D) | 480 x 44x 360.2mm | | Net Weight | 4.2kg |
|
Reviews
There are no reviews yet.