Content |
The 481 and 482 are slave units which include all of the functionality and features of the 480 . They both incorporate 4 inputs and 8 outputs with Euroblock connectors on the 481 and XLRs on the 482. However, they do not include the front panel programming interface. All programming functions can be performed through the 480, the 480R, or via the Windows GUI. An unlimited number of slaves can be chained together.
Features: 4 Input and 8 Outputs with routing 31 band graphic or 9 band parametric equalizer on every input (pre-crossover) Dual Real Time Audio Analyzers Butterworth, Bessel or Linkwitz-Riley crossover filters 27 Different Crossover Configurations Time Alignment and Transducer Alignment Delays Compressor/Limiter on every output Speaker Compensation EQ (post crossover) Multi-level Security System Separate House and Show EQ with individual lockout Triple redundant back-up of all parameters when running network, 480R and PC GUI TYPE IV? Conversion System Electronically balanced/RF filtered Euroblock Inputs and Outputs Proprietary RS-485 Control Network RS-232 PC Interface for computer display and configuration |
The ARX EC-2 is a flexible yet affordable 24 dB per octave Phase Correct active crossovers. It has 2 modes of operation; as either Stereo 2 way or a Mono 3 way units, with a switch on the back panel selecting either mode.
Features Ultra low noise circuitry Totally phase aligned at crossover point Switchable Dual Channel 2 way or Single Channel 3 way Unique 'semi-fixed' crossover point 24dB per octave (Fourth Order) Linkwitz-Riley filters Separate Summed Mono Output Balanced Inputs and Outputs Built in High Pass filters Intuitive, 'user friendly' layout Flawless performance in any audio environment
Tamper-Proof Crossover Points The crossover points are determined internally by the value of 4 resistors per channel; changing the resistor value changes the crossover point. This 'semi fixed' method avoids the pitfalls of externally adjusted crossover points, making the crossover points tamper-proof once they are set. Idle fingers can't fiddle with the crossover points and create havoc with the system! As a handy guide, a list of common crossover points and their corresponding resistor values are printed inside the unit's lid, and also set out in the Owner's Manual. On the front panel are level controls for Low and High in dual channel 2 way mode, and Low, Mid and High in single channel 3 way mode, with corresponding Outputs on the rear panel.
Balanced Inputs and Outputs EC-2 has Balanced Inputs and Outputs, on XLR connectors. The EC-2 also has an additional summed Mono Low output, for applications that need a Mono Low feed (e.g. Left and Right full-range plus a single Sub Bass speaker). High Pass Filter There is also a preset 30 Hz HighPass filter to remove unwanted subsonics which can damage speakers and waste amplifier power. In addition, each output has up to +6 dB of gain available, to compensate for amplifiers and speakers of differing sensitivities. Universal AC Power AC power range is a universal 100 to 120V or 220 to 240VAC, and is connected to the unit via a standard IEC connector, with built-in fuse and voltage change switch. Uncompromising Audio Quality Innovative circuit design is pointless unless it delivers stunning sound quality, and here the EC-2 excels. It has been designed for uncompromising audio quality, and to achieve this, Linkwitz Riley 24dB (Fourth Order) state variable filters are used throughout, ensuring a smooth Phase Correct transition through the crossover region. From Stage Monitors to Studio Monitors, from Front of House to the Front room of your House, the ARX EC-2 is a crossover that is suited to any application that requires flawless, transparent sound. You'll never compromise on Quality when you choose ARX
T E C H N I C A L S P E C I F I C A T I O N S
Input Impedance Balanced 20 Kohms, Unbalanced 10 Kohms Input Headroom + 21 dB CMRR >45 dB, 20 Hz-20 KHz Output Impedance Balanced 300 ohms, Unbalanced 150 ohms Output Level (Max) + 21dB Frequency Response 30Hz-20KHz +or- 0.5dB Note: 30 Hz is a function of the High Pass filter Signal to Noise ratio (Controls at Unity) -90 dB Unweighted, -93 dB 'A' weighted Distortion 004% THD,0dB,1KHz Dynamic Range 111 dB Power Requirements 100/120 V AC, 220/240 V AC Weight 5 lbs/2.2 Kg Dimensions 19“W x 13/4“H x 6“D, 482 x 44 x 155mm Input Connector type XLR Output Connector type XLR Crossover point frequencies are changed internally by varying the value of 4 resistors per channel.
Front Panel Controls Low and High Output controls for 2 way mode Low, Mid and High Output controls for 3 way mode Marker panels for labelling crossover assigns 2 way/ 3 way status LEDs Rear Panel Balanced XLR Inputs and Outputs Additional summed mono Low output 2 way / 3 way mode switch |
Full-featured Speaker Processing in a 1U Space
Speaker processing can be a complicated business requiring a substantial array of equipment, but the Yamaha SP2060 offers everything you need in a single rack space. This innovative 24-bit, 96-kHz digital speaker processor delivers excellent sound quality, an impressive variety of processing functions — gain, delay, PEQ, comp, crossover, limiter, and an all-pass filter for phase adjustment — and intuitive programming from Yamaha's DME Designer application running on a personal computer. It has two analog inputs and six analog outputs, plus two AES/EBU format digital inputs for connectivity with a broad range of systems. And if you use Yamaha Installation Series Speakers, all you need to do is select one of the many optimized presets provided for great sound with minimum measurement and setup time. The SP2060 is a compact, portable 1U unit that is ideal for live sound or installations.
Sampling Frequency | Internal Clock | 96kHz | External Clock | Normal Rate | 44.1, 48kHz (±0.1%) | Double Rate | 88.2, 96kHz (±0.1%) | Signal Delay | 761µsec Input to Output, fs = 96kHz | Frequency Response | 20Hz -40kHz (TYP 0dB, MAX +0.5dB, MIN -1.0dB), fs=96kHz, RL=600ohms | Total Harmonic Distortion | 0.007% (+22dBu@1 kHz),
0.05% (+4dBµ@20 Hz - 40kHz)
fs=96kHz, RL=600ohms;
measured with 18dB/octave filter @80kHz | Hum & Noise | TYP -82dBu,
fs=96kHz, RL=600ohms, Rs=150 ohms;
measured with 6dB/octave filter @12.7kHz;
equivalent to a 20kHz filter with ∞ dB/octave attenuation. | Dynamic Range | 106dB AD+DA
fs=96kHz, RL=600ohms;
measured with 6dB/octave filter @12.7kHz;
equivalent to a 20kHz filter with ∞dB/octave attenuation. | Crosstalk @1kHz | -80dB INPUT to Output
fs=96kHz, measured with 18dB/octave filter @80kHz | Power Consumption | 30W | Dimensions (W x H x D) | 480 x 44x 360.2mm | Net Weight | 4.2kg |
|
Lab Gruppen NLB 60E
The NomadLink network provides remote monitoring, control and power sequencing functions for multiple C Series or FP+ amplifiers. Indeed up to 16 NLB 60E network bridges, each monitoring up to 60 amplifiers may be accommodated in one system. Easy setup, redundancy, and minimum maintenance were bywords when developing this network format.
NomadLink is a closed-loop, daisy-chained network topology with the NLB 60E providing the bridge to the familiar world of Ethernet/LAN. NomadLink reduces installation time and cost significantly, includes redundancy during operation by design and simplifies the location of faults or system abuse.
NomadLink together with the associated DeviceControl software allows the subnets’ architecture to be automatically uploaded even without individual IP addresses in the amplifiers. All in all, it is the fastest and easiest monitoring and control network on the market today.
Specifications:
Network Connectors:
* Nomadlink Out: EtherCon housed RJ45
* Nomadlink In: EtherCon housed RJ45
* Ethernet rear-panel: EtherCon housed RJ45
* Ethernet front-panel: Standard RJ45
General Purpose Inputs (GPI):
* One Voltage sensing input: Two pole Phoenix
* Two contact closure inptus: Two pole Phoenix
Front Panel Indicators:
* Front operation locked: Yellow LED
* Fault warning: Red LED
* Amplifier subnet muted: Red LED
* NomadLink network connected/activity: Blue LED
* Ethernet connected: Orange LED
* Ethernet Activity: Yellow LED
2 x 16 Character display: White text, Blue background
Navigation and Adjust keys: Yes, x 6
Subnet Power on/off keys: Yes, x 2
Power: 100 to 240 VAC, 50 to 60 Hz (auto-select)
Power consumption:
Finish: Anodized aluminum front, Plated and painted steel chassis
Approvals: CE, CSA
Dimensions (W x H x D): 19" x 1.73" x 8.2" (483 x 44 x 208 mm), 1 RU
Weight: 5 lbs. (2.25 kg)
|
Power supply: |
100-240 V AC, 50/60 Hz
6 V DC 800 mA |
Power connection: |
Mains input via Coaxial power connector (M) mounting version power supply cord with AC adapter (provided) |
Frequency range: |
10 - 30000 Hz |
THD: |
<0,005 % at 1 kHz |
DSP: |
Digital signal processor |
Impedance: |
Input: 10 kOhm
Output: 50 Ohm |
Gain: |
Output: -50 dB to +12 dB |
Filter: |
Linkwitz-Riley; Butterworth; Bessel; 6db/oct; 12db/oct; 18db/oct; 24db/oct |
Delay: |
0 - 5 ms |
Dynamic range: |
Input: 114 dB
Output: 110 dB |
Sample rate: |
67 kHz |
Connections: |
Input: line via 2 x 3-pin XLR
Output: line via 6 x 3-pin XLR |
Crossover frequency: |
20-20000 Hz |
Max. level: |
Input: +22 dBu
Output: +9 dBu |
USB port: |
Typ B |
PC connect: |
DXO Software via USB, firmware can be updated |
Housing design: |
(19") 48.3 cm rack installation 1 U |
Dimensions: |
Width: 48,3 cm
Depth: 12,8 cm
Height: 4,45 cm |
Weight: |
1,77 kg |
Operating system: |
Win XP, Win Vista, Win 7, Win 10, OS X 10,5 or better |
| Behringer DCX2496 Overview
The DCX2496 ULTRADRIVE PRO from Behringer is a digital loudspeaker management system, that provides excellent audio quality, along with a comprehensive feature list. It allows for precise set-up of multiple loudspeaker arrays, suitable for live sound, fixed installations that require control of loudspeaker systems, and other contractor-installed applications.
Each of the three-inputs and six-outputs have fixed processing blocks, including gain, delay, EQ and dynamic EQ on the input channels, and gain, crossover, EQs, limiter and delays on the output side. One of the inputs can accept a stereo AES/EBU digital signal. An integrated sample rate converter assists in accepting various sample rates. Additionally, an internal input-sum signal is easily set-up.
Four different mono and stereo output operating modes are available, all with individual crossover filter types with selectable roll-off characteristics. Input and output delays allow for time adjusting signals to compensate for ambient temperature changes or for adjusting arrival time differences for individual speaker clusters. EQs can be used for both musical enhancement or for level-dependent equalization. Brick-wall limiters guarantee speaker protection.
Remote control of one or several units can be accomplished utilizing downloadable software for a Windows based computer. Set-ups can be saved to the software, or to an optional PCMCIA card for the ultimate in portability. Servo-balanced, gold-plated XLR connectors for all inputs and outputs guarantee excellent connectivity.
- Three-input, six-output loudspeaker management system
- Four different mono- and stereo-output operating modes
- Individual crossover filter types including Butterworth, Bessel and Linkwitz-Riley, with selectable roll-off characteristics from 6dB to 48dB per octave
- Choice of high-, band- and low-pass filters for each input and output
- Dynamic EQ for level-dependent equalization and parametric EQ selectable for each channel
- “Zero" attack limiters on all output channels for optimal signal protection
- Automatic or manual-adjustable delays for all inputs and outputs allow for adjustment due to room temperature, phase and arrival time differences
- Link option via RS-485 network interface allows for linking multiple units for larger installation requirements
- Downloadable software enables single- or multiple-unit remote control utilizing a Windows based computer
- Sixty user-defined internal presets can bestored via software or on a PCMCIA card
- Internal universal power supply allows the unit to operate virtually anywhere
Frequency Response |
10Hz to 35kHz, -1dB |
Dynamic Range |
109dB |
Input Connections |
3 x XLR |
Output Connections |
6 x XLR |
Input Impedance |
20kΩ @ 1kHz |
Output Impedance |
160Ω @ 1kHz |
Maximum Input Level |
+22dBu |
Maximum Output Level |
+22dBu |
Sample Rate |
32kHz to 96kHz |
RTA Mic Phantom Voltage |
+15V |
Crosstalk (Main Outputs) |
-100dB @ 10dBu In |
THD & Noise |
0.007% @ 0dBu In |
Dimensions |
19" x 8.5 x 1.75" (483 x 217 x 45mm) |
Weight |
6.6 lbs (3 kg) |
|
Reviews
There are no reviews yet.