| Content |
Power Output Level R-300 PLUS
STEREO
8ohm(T.H.D 0.05%) 170W+170W
4ohm(T.H.D 0.05%) 250W+250W
BRIDGED MONO
8ohm(T.H.D 0.05%) 460W
8ohm(T.H.D 0.5%) 500W
Frequency Response 20Hz- 20kHz, ±0.5dB
Convection Cooled
SoftStart Protection System
Balanced 10kΩ@0.775V Inputs
|
- Output Power:
500W RMS Per Channel @ 4 Ohms, 1kHz, 0.1% THD
330W RMS Per Channel @ 8 Ohms, 1kHz, 0.1% THD
- Bridge Mode, Mono 820W RMS @ 8 Ohms, 1K Hz, 1% THD
- Total Harmonic Distortion: Less Than 0.1% (20Hz - 20kHz @ 8 Ohms)
- Frequency Response: (+/-01db, @rated output Power, 8 Ohms): 20Hz - 20K Hz
- Slew Rate: 15V Per usec
- Damping Factor: @ 8 Ohm: 300
- Impedance: 20 Ohms balanced / 10 Ohms unbalanced
- Cooling System: 2 individual fans
- Special Features: High/Low Pass Filter / Input Sensitivity Selector / Ground Lift; Limiter
- build in clip limiter
- Input: XLR 3pin + Jack 6,3mm
- output: Speakon + Binding post
- Dimensions (LxWxH): 360 x 482 x 88mm 2-rack mount spaces
- Weight: 15 KG.
|
XB Series - Intelligent Power
Power Without Compromises.
The XB is designed for paging, music and alarm signals. Versatile, dynamic
and extremely rugged according to IEC286-3. For the highest requirements
in safety and quality.
Sequential power on, alive contacts and incorporated ground fault detection-
the XB is the solution under all conditions. Without the need for additional
equipment. For uninterrupted and troublefree operation.
High Tech SMT Design
Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter,
3 ms Muting Delay
PHOENIX / Speakon
LED Indicators for POWER, SIGNAL, CLIP, PROTECT
Temperature controlled, variable speed low noise fans
Volume Controls at the back
Stereo / Bridged / Parallel Mode
Softstart
Sequential Remote Power On
Alive Contact
Ground Lift
3 Years Warranty
TECHNICAL DATA:
XB 400: 2x 200 W @ 4 Ohm
Class: AB
Frequency Response: 20 Hz - 20 kHz (0 / -0.3 dB)
THD: < 0.025%
Signal-to-Noise Ratio: < 103 dB
Channel Seperation: > 85 dB
Input Sensitivity: +6 dBu
Input Clipping: 22 dBu
Input Impedance: 20 kOhm
Damping Factor: 500 @ 4 Ohm
Cooling: 2x fan (temp. reg. variable speed)
Weight:12 kg /(26 lbs)
Dimensions: 2 RU / 483 x 88 x 382 mm (19" x 3.5" x 15“) |
XB Series - Intelligent Power
Power Without Compromises.
The XB is designed for paging, music and alarm signals. Versatile, dynamic
and extremely rugged according to IEC286-3. For the highest requirements
in safety and quality.
Sequential power on, alive contacts and incorporated ground fault detection-
the XB is the solution under all conditions. Without the need for additional
equipment. For uninterrupted and troublefree operation.
High Tech SMT Design
Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter,
3 ms Muting Delay
PHOENIX / Speakon
LED Indicators for POWER, SIGNAL, CLIP, PROTECT
Temperature controlled, variable speed low noise fans
Volume Controls at the back
Stereo / Bridged / Parallel Mode
Softstart
Sequential Remote Power On
Alive Contact
Ground Lift
3 Years Warranty
TECHNICAL DATA:
XB 800: 2x 400 W @ 4 Ohm
Class: AB
Frequency Response: 20 Hz - 20 kHz (0 / -0.3 dB)
THD: < 0.025%
Signal-to-Noise Ratio: < 103 dB
Channel Seperation: > 85 dB
Input Sensitivity: +6 dBu
Input Clipping: 22 dBu
Input Impedance: 20 kOhm
Damping Factor: 500 @ 4 Ohm
Cooling: 2x fan (temp. reg. variable speed)
Weight: 13 kg/(29 lbs)
Dimensions: 2 RU / 483 x 88 x 382 mm (19" x 3.5" x 15“)
|
The high efficiency of the ED series enables maximum efficiency with low heat generation.
A new and unique Class-H circuity technology using state of the art SMD Surface Mount Technology with a reduced number of components offering performance levels exceeding audiophile levels like a slew rate of 50V/µs and high-end extended dynamic sound. The amplifier provides 2x300W into 4 Ohm is equipped complete with temperature-controlled fan cooling, all common protective circuits such as over-temperature, short circuit, RFI and soft start.
The integral soft clip limiter protects against damage to the connected loudspeakers, the activity of a protective circuit, signal and limiter are shown for each channel by LEDʼs.
| AMPLIFIER SPECIFICATIONS |
|---|
| Power output stereo 4Ω: | 2 x 300 Watt rms | | | Power output stereo 8Ω: | 2 x 180 Watt rms | | | Power output bridged 8Ω: | 600 Watt rms | | | Frequency Response: | 20 Hz ÷ 20 kHz | | | Signal/noise rate: | > 105 dB | | | Crosstalk: | > 70 dB | | | Distortion (THD+N): | | | | Intermodulation: | | | | Damping factor: | 200:1 (8 Ω) | | | Slew rate: | 50 V/μS | |
| INPUT SECTION |
|---|
| Input connector: | 2 x XLR balanced, 6,3mm jack unbalanced | | | Input sensitivity: | 0 / 0.775 dBm/V RMS | | | Input impedance: | 10.000 kΩ | | | Controls: | Volume control for each channel | |
| OUTPUT SECTION |
|---|
| Output connector: | 2 x Neutrik Speakon 4 ways | |
| SYSTEM PARAMETERS |
|---|
| Cooling: | Two-speed fan | | | Protections: | Temperature, DC, RFI short circuit, Soft-Start thermal on transformer | | | Amplifier class: | H | |
| POWER REQUIREMENT |
|---|
| Operating voltage: | 220÷240 / 110÷120 ~ 50 / 60 V ~ Hz | | | Max.current: | 6 A | | | Power Consumption: | 1300 W | |
| PHYSICAL SPECIFICATIONS |
|---|
| Height: | 88 / 3.46 mm/inch | | | Width: | 483 / 19.01 mm/inch | | | Depth: | 350 / 13.77 mm/inch | | | Net Weight: | 11.45 / 25.24 Kg/Lbs | |
| SHIPPING INFORMATION |
|---|
| Package height: | 120 / 4.72 mm/inch | | | Package width: | 540 / 21.25 mm/inch | | | Package depth: | 470 / 18.05 mm/inch | | | Shipping Weight: | 13.81 / 30.44 Kg/Lbs |
| Phonic's MAX 1500 Power Amplifier provides 900 Watts of power at 8 ohms (bridge mono) or 450 Watts at 4 ohms (stereo) - ideal for clubs, churches, auditoriums and more. Input to the MAX 1500 amp is achieved via XLR or phone jack, and output is achieved either through Speakon-type connectors or traditional binding posts. The MAX 1500 features ground switches, user defeatable clip limiters, selectable high pass filters, and the option to choose between stereo, parallel and bridge operating modes, making this amplifier ideal for real world application.
- Output power: 450W @ 4 Ohms stereo, 280W @ 8 Ohms stereo
- High-current toroidal transformers for greater power and low noise
- Independent user-defeatable peak limiters reduce distortion
- Selectable High-Pass filter at 30Hz or 50Hz
- XLR and 1/4' TRS input jacks
- Binding post and Speakon?-type outputs
- Front mounted gain controls for easy access
- Signal and Peak LED indicators to monitor performance
- Short circuit, thermal, subsonic, RF protection, output DC offset
- Power on/off muting
|
Reviews
There are no reviews yet.