Content | ACTIVE DI-BOX, plug in/out, XLR in/out, changeable chassis, only use with phantom power, 30 dB Groundlift.
Brand |
KLARK TEKNIK |
Model |
DN100 |
DI Type |
Active |
Channels |
Mono |
Application |
Concert, Portable PA, Studio |
Warranty |
3 Years |
The new Klark Teknik DN100 Direct Injection Box is the
natural successor to the long-established LBB100.
A ground-up redesign provides an extended dynamic range,
lower noise floor and all the world-class audio performance
you?d expect from Klark Teknik. DN100 is also designed to
handle the rigours of life on the road: a thick aluminium shell
protects the electronics, and this in turn is protected by a
tough silicone rubber casing, which is replaceable and available
as a spare part.
We?ve also fitted a Kensington security slot in one of the end
panels to allow the unit to be made secure using a Kensington
MicroSaver security cable.
Attention to detail ? it?s what makes a good unit into a great one.
DN100 Technical Data:
Input:
Type active electronic, balanced or unbalanced
Impedance 1M ohms nominal, balanced or unbalanced (jack connectors)
20K ohms (XLR input only)
Connectors 2 quarter inch jacks and 3-pin XLR linked in parallel
Max. Level 30dBu
Attenuator 30dB, switchable
Output:
Type Transformer Isolated, balanced
Impedance 300 ohms
Connector 3 pin XLR
Max. Level 10dBu with load >2k ohms
Min. load 600 ohms
Performance:
Noise -100dBu, 20Hz to 20kHz unweighted, with input terminated by 10k resistor
Frequency response +0.5/-1dB 20Hz to 20kHz
Distortion (THD+N) |
You're serious about getting rid of all that excess noise on stage, but you've got so many line instruments you don't know where to start. The ADB-4 from Stewart can take care of all your high impedance problems. The ADB-4 is 4 active direct boxes, all in a module that only takes up half a space on your keyboard rack. It's a rugged, durable piece of equipment that packs a lot of DI power.
? Requires phantom power or 9v battery ? Ground lift switch ? Instrument or speaker level switch ? Transformerless ? Can be used with amp up to 400w ? RF shielding |
Tube-buffered DI-Box DI-1000
The Tube-Buffered DI-Box DI-1000 allows the extraction of all the musical details of musical interfaces without degrading the sound. This can only be achieved by providing a very high input impedance to avoid any loading of instrument pickups.This design approach allows seemingly infinite headroom to preserve the real dynamic range of the interfaced instruments.A vacuum tube enables all these goals to be achieved without any compromises in sound quality.The sonic difference between a standard DI-Box and the Tube-Buffered DI-Box is comparable to the musical resolution difference between a standard microphone and a studio microphone.One of the best transformers, the very transparent sounding JENSEN JT-DB-E, was chosen providing complete ground isolation. The parameters of this transformer, like frequency response, phase response, group delay and geadroom capabilities, play a vital part in the performance of this DI-Box. Technical Specifications Input The signal of the instrument is directly fed to the tube circuit with > 20 MOhms input impedance to prevent any signal degradation, inevitable in traditional designs. Buffered Output“ The second stage of the vacuum tube is used to buffer the signal and lower the output impedance to < 8 kOhms. This unity gain output allows for cable runs of 10 meters without loosing high frequency information. Boost circuit The boost circuit increases the signal send to the output transformer by 15 dB. This may be useful for instruments with extremely low output, but decreases headroom capability to 6 Volt rms. Under these circumstances the signal may be clipped, concerning the output transformer?s signal, which gives you 2nd harmonic tube-like distortion. This distortion normally does not occur - but is sometimes desirable, being the reason for this special feature. Unity circuit The unity circuit feeds a low distortion unity gain signal to the JENSEN output transformer. This gives the best possible sound quality. Ground-lift“-Switch This front panel mounted switch allows complete ground and electrical isolation between the direct injection box and the console or recording device.
Mechanical Specifications Cabinet 2 mm stainless steel Front- and rear-panel 1,5 mm stainless steel lasercut and photo-chemically etched Dimensions 185 x 100 x 40 mm Vibration insulation 4 high-compliance rubber-elements Operating Voltage 220/110 V AC, selectable via rear panel mounted switch. The fuse is easily accessible from the rear panel. IEC mains connector with optional fixture. Construction details Double sided glass fibre contacted PCB with 70 mm copper plating. 1% metal film resistors and the finest polypropylene capacitors are used in the signal path. MIL type Switchcraft jacks and high performance switches ensure flawless operation. The power supply is optimised via measurement quality toroid transformer and a low impedance design to ensure the lowest possible noise. Through a double sided PCB all parts are roadworthy secured. A waterclear blue LED perfects the aesthetics of the DI box.
Technical Data Input impedance > 20 MOhm Output impedance180 Ohm at 1 kHz Frequncy response 20 Hz - 20 kHz (-0,1 dB) 5 Hz - 120 kHz (-3 dB) THD at 0 dBv 0,06% at 20 Hz 0,04% at 1 kHz 0,035% at 20 kHz Signal to Noise Ratio 86 dB Tube ECC 83/7025 A - military E 83 CC optional Output transformer JENSEN JT-DB-E Polarity Pin 2 Hot , AES/IEC -Standard Max. Input voltage > 30 V peak |
Inline Transformer IA-2
The model IA-2 line matching transformers !S designed to properly match a low impedance signal to a low impedance source. The advantage of "ground lift" switching allows to optmize hum problems. Technical Data Frequency response 20 Hz - 20 KHz + 1 dB Impedance 600 : 600 Ohm THD K3 50 Hz = 0.5 % Level < + 6 dBm Weight 100 g Dimensions diameter 17 mm, lenght 115 mm | 2-channel passive DI box for line and loudspeaker levels. PAN-04 consists of a housing containing the equivalent of two PAN-01s, making it a dual channel passive DI box. This „stereo" configuration makes it ideally suited for use with certain keyboards and devices which have several outputs.ive DI box. Jack input with paralell „THRU" output, transformer balanced XLR output. Attenuable input sensitivity, can handle both line level and speaker level signals.
Specifications
- No. of channels: 2
- Passive/Actibe: Passive
- Transformer balanced: Yes
- Attenuator: -30 dB
- Input/Output Gain: -20 dB
- Ground lift switch: Yes
- Max Input Level: +54 dBu
- Max Output Level: +4 dBu
- Frequency Range 2K Source Imp. -1dB: 10 Hz - 40 kHz
- Input Impedance 60Hz: 60 kΩ
- Nom. Output Impedance: 600 Ω
- Housing: Steel
- Dimension: 110 x 110 x 45 mm
|
1-channel DI box, passive Converts unbalanced 6.3 mm jack line input (e.g. from instruments) into balanced XLR output for connecting a mixer Switchable input attenuation: 0 dB, -20 dB, -40 dB Ground-lift switch eliminates ground loop problems 1 signal input (6.3 mm jack) 1 parallel output (6.3 mm jack), feed-through of the input signal 1 low-impedance output (XLR) Gray housing |
Reviews
There are no reviews yet.