Content |
The iP 2100 is a space-saving power amplifier, ideal for use in installations as well as in cost-effective live sound systems. The Iron Power (iP) family of power amplifiers is the new compact and versatile line of professional power amplifiers with classic toroidal iron transformers. To achieve a compact design, the latest semiconductor technology is utilized. This, together with Lab.gruppen?s proprietary copper cooling system, Intercooler?, enhances the 2 ohms capacity. A new Bi-phase wiring scheme also increases the capacity of the power supply. This extends the power bandwidth in the low end.
Key Features: 2 x 425 watts @ 8 ? 2 x 700 watts @ 4 ? 2 x 1050 watts @ 2 ? (Measured just below clip level, with both channels driven) Compact design: 2U high Intercooler? cooling system with front-to-rear airflow Multiple positions gain switch Easily accessible dust filter Improved low-end power bandwidth Neutrik Combo jack and Phoenix terminal block input connectors Bridged mono outputs in one SpeakOn connector
Besides the traditionally superb Lab.gruppen sonic performance, there is a full line of features to make the iP family functional in all situations from installation to cost-effective live sound systems:
Multiple positions Gain switch To meet the demands for a flexible gain structure in the system, Lab.gruppen offers a multiple position gain switch. The maximum amplifier gain can be set to all industry standards: 20, 23, 26, 29, 32, 35, 38 and 41 dB.
Versatile input connection With the Neutrik Combo-jack we offer both the professional XLR-type standard and the semi-pro 1/4? TRS phono-jacks. For installations the 3-pin Phoenix terminal block may be handier.
Soft Start Toroidal transformers require a huge amount of start current to build up a magnetic flux when the amplifier is switched on. Therefore Lab.gruppen have included a soft start circuit to minimize the risk of blowing the wall fuse and to reduce flickering in the lighting.
Sophisticated protection circuitry, combining: ALStm short circuit protection; the Adaptive Limiting System permits very high peak currents, but keeps the amplifier within the Safe Operation Area. DC protection; protects against infrasonic signals VHF protection; protects the loudspeakers against strong very high frequency non-musical signals above the audible range. Thermal protection; prevents the amplifier from being overheated. The protection indicators on the front panel are switched on, as a warning, before the protection process is initiated. AC protection; shuts down the power supply if the line voltage is outside the operating voltage. Clip limiter; prevents severely clipped waveforms from reaching the loudspeakers, whilst maintaining full peak power.
|
Crown DSi 2000 2x800W-4Ω Power Amplifier
The Crown? DSi 2000 power amplifier shall be a solid-state two-channel model with a switch-mode universal power supply. A rear-panel HD-15 connector shall provide input/output connectivity between the DSi amplifier and the DSi-8M System Monitor.
The outputs shall be usable as stereo or bridged-mono modes of operation.
The bridged-mono mode shall bridge the outputs to provide increased output voltage.
Front panel controls and indicators shall include the following:
Level: Detented rotary level control, one per channel.
Power Switch: On/off switch applies AC power to the amplifi er.
Sel/Prev/Next Buttons: Three buttons near the LCD screen shall be used to access menu items and front panel lockout.
LCD Screen: Backlit liquid crystal display shows speaker presets and signal processing.
Signal Indicator: Green LED, one per channel, illuminates when a very low-level signal is present at input.
?10 Indicator: Green LED fl ashes when output signal exceeds ?10 dB below clip.
?20 Indicator: Green LED fl ashes when output signal level exceeds ?20 dB below clip.
Ready Indicator: Green LED, one per channel, illuminates when the amplifier is ready to produce audio.
Clip Indicator: Red LED, one per channel, turns on at the threshold of audible distortion.
Temp Indicator: Red LED, one per channel, illuminates under excessive temperature conditions.
Power Indicator: Blue LED illuminates when the amplifi er has been turned on and has power.
Rear panel controls and connectors shall include the following:
AC Line Connector: NEMA 5-15P (15A).
Input Connector: Two 3-pin removable Phoenix-type connectors each accept a balanced line-level input signal.
Output Connectors: 4-position barrier strip with connectors for dual louspeakers or bridge-mono loudspeaker.
HiQnet USB Connector: Type B, connects to a HiQnet network.
HD-15 Connector: For cinema I/O compatibility with DSi-8M System Monitor.
The amplifier shall have the following specifications:
Output Power: 2 ohm Stereo (per channel): 1,000W with 1% THD, 4 ohm
Stereo (per channel): 800W with 0.5% THD, 8 ohm Stereo (per channel) 475W
with 0.5% THD, 4 ohm Bridge-Mono: 2,000W with 1% THD, 8 ohm Bridge-
Mono: 1,600W with 0.5% THD.
Voltage Gain at 1kHz, 8 ohm rated output: 26 dB.
Frequency Response: +0/?1 dB from 20 Hz to 20 kHz at 1 watt into 4 ohms.
Load Impedance: Safe with all types of loads. Rated for 2 to 8 ohms in Stereo
mode, 4 to 16 ohms in Bridge-Mono mode.
Sensitivity at 8 ohm rated output: 3.09V.
Sensitivity at 4 ohm rated output: 2.84V.
Sensitivity at 2 ohm rated output: 2.24V.
Signal to Noise Ratio (below rated 8-ohm power at 1 kHz): 105 dB
(A weighted).
Damping Factor: Better than 500 from 20 Hz to 500 Hz.
Crosstalk: > 70 dB below rated power, 20 Hz to 1 kHz.
Input Stage: Input is electronically balanced and employs precision 1% resistors.
Input Impedance (nominal): 20 k ohms, balanced;10 k ohms,unbalanced.
Maximum Input Signal: +22 dBu typical.
|
InterM V-2000 Power amplifier 2Χ550W/4ohm, 2Χ300W/8ohm, 2Χ900W/2ohm bridge 1900W/4ohm |
The high efficiency of the ED series enables maximum efficiency with low heat generation.
A new and unique Class-H circuity technology using state of the art SMD Surface Mount Technology with a reduced number of components offering performance levels exceeding audiophile levels like a slew rate of 50V/µs and high-end extended dynamic sound. The 2U amplifier provides 2x550W into 4 Ohm is equipped complete with temperature-controlled fan cooling, all common protective circuits such as over-temperature, short circuit, RFI and soft start.
The integral soft clip limiter protects against damage to the connected loudspeakers, the activity of a protective circuit, signal and limiter are shown for each channel by LEDʼs.
AMPLIFIER SPECIFICATIONS |
---|
Power output stereo 4Ω: | 2 x 550 Watt rms | | Power output stereo 8Ω: | 2 x 265 Watt rms | | Power output bridged 8Ω: | 1100 Watt rms | | Frequency Response: | 20 Hz ÷ 20 kHz | | Signal/noise rate: | > 105 dB | | Crosstalk: | > 70 dB | | Distortion (THD+N): | | | Intermodulation: | | | Damping factor: | 200:1 (8 Ω) | | Slew rate: | 50 V/μS | |
INPUT SECTION |
---|
Input connector: | 2 x XLR balanced, 6,3mm jack unbalanced | | Input sensitivity: | 0 / 0.775 dBm/V RMS | | Input impedance: | 10 kΩ | | Controls: | Volume control for each channel | |
OUTPUT SECTION |
---|
Output connector: | 2 x Neutrik Speakon 4 ways | |
SYSTEM PARAMETERS |
---|
Cooling: | Two-speed fan | | Protections: | Thermal, direct current, RFI, short circuit, transformer protection | | Amplifier class: | H | |
POWER REQUIREMENT |
---|
Operating voltage: | 220÷240 / 110÷120 ~ 50 / 60 V ~ Hz | | Max.current: | 10 A | | Power Consumption: | 2200 W | |
PHYSICAL SPECIFICATIONS |
---|
Height: | 88 / 3.46 mm/inch | | Width: | 483 / 19.01 mm/inch | | Depth: | 350 / 13.77 mm/inch | | Net Weight: | 15 / 33.06 Kg/Lbs | |
SHIPPING INFORMATION |
---|
Package height: | 120 / 4.72 mm/inch | | Package width: | 540 / 21.25 mm/inch | | Package depth: | 475 / 18.07 mm/inch | | Shipping Weight: | 17 / 37.47 Kg/Lbs |
|
Number of Channels: 2
Output Power: (per channel)
8 ohms 450W
4 ohms 850W
2 ohms 1550W
Output Power: (bridged)
8 ohms 1700W
4 ohms 3100W
THD%: (@1dB below max output)
@ 1kHz | Phonic\'s MAX 2500 Power Amplifier provides 1500 Watts of power at 8 ohms (bridge mono) or 750 Watts at 4 ohms (stereo)- ideal for medium to large-size clubs, churches, auditoriums and more. Input to the MAX 2500 amp is achieved via combo connectors that accept both XLR and 1/4\' jacks, and output is achieved through either Speakon?-type connectors or binding posts. The MAX 2500 features ground switches, user defeatable clip limiters, selectable high pass filters, and the option to choose between stereo, parallel and bridge operating modes, making this amplifier ideal for real world application.
- Output power: 750W @ 4 Ohms stereo, 500W @ 8 Ohms stereo
- High-current toroidal transformers for greater power and low noise
- Independent user-defeatable peak limiters reduce distortion
- Selectable High-Pass filter at 30Hz or 50Hz
- XLR and 1/4\' TRS input jacks
- Binding post and Speakon?-type outputs
- Front mounted gain controls for easy access
- Signal and Peak LED indicators to monitor performance
- Short circuit, thermal, subsonic, RF protection, output DC offset
- Power on/off muting
|
Reviews
There are no reviews yet.