Content |
•
|
2-way bi-amplified, optimized Active loudspeaker system
|
•
|
High-output precision titanium compression driver
|
•
|
Neodymium long-throw low frequency transducer with 3-inch voice coil
|
•
|
Servo Feedback controlled woofer for tight low-end punch
|
•
|
300W class-D, Fast Recovery LF amp / 100W HF amp
|
•
|
Ultra-wide, smooth dispersion via multi-cell horn aperture and HF waveguide
|
•
|
Built-in phase-accurate 24dB Linkwitz-Riley electronic crossover
|
•
|
Mackie Active Electronic time alignment, phase correction and EQ for studio quality sound
|
•
|
Mic/line input and pass-thru connector
|
•
|
Lightweight for ultimate portability (40lbs)
|
•
|
Flyable, Pole Mountable, Floor Wedge-able
|
|
The tops of the LDBLOCKX Power Tower are fitted with 12" custom made midrange speakers and a 1" Celestion Driver, they are driven by a 450 W RMS Bi-Amp amplifier producing a maximum sound pressure level of 128 dB.
Specifications LD Block X 12" Topteil Active: - Model Name: LDATOP12
- Type: Bassreflex
- Components:
- Woofer: 12" Custom Made
- Compression Driver: 1" Custom Made
- Amplification: Class A / B (Bi-Amp)
- Dispersion: 60° x 40°
- Power (RMS): 350 W + 100 W
- Frequency Range: 80 Hz - 20 kHz
- SPL (1 W/ 1 m): 101 dB
- Max SPL: 128 dB
- Protection: Limiter, Thermal, DC, Short circuit, HF
- Controls: Main Volume, Tweeter Volume, switchable High Pass (80 / 120 Hz), On/Off Switch
- Indicators: Power, Limiter, Signal, Protect
- Connectors:
- Input: Line: XLR + Jack 6,3mm (Combo)
- Output: Line: XLR
- Power Supply: Transformer
- Cabinet Material: 15 mm Plywood
- Cabinet Surface: Painting
- Dimensions (W x H x D): 450 x 500 x 520 mm
- Features: Ergonomic milled handles
|
Features
400 Watt digital bi-amplification
128 dB max spl
Wide dispersion 90 x 60 constant directivity horn
12" High power woofer, 3" voice coil
2" Titanium dome, high frequency driver
DSP processing, boost eq, soft limiter and protection
Xlr/jack input, xlr signal output
Acoustical Specifications
Frequency Response -3 dB: 45 Hz ÷ 20 kHz
Max SPL: 128 dB
Horizontal coverage angle: 90°
Vertical coverage angle: 60°
Compression Driver: 2" 2.5" voice coil
Woofer: 12" 3" voice coil
Input/Output Section
Input connectors: xlr-jack
Output connectors: xlr
Processor Section
Crossover frequencies: 1300 Hz
Controls: Flat, Boost
Amplifier Specifications
Total power: 400 W
High frequencies: 100 W
Low frequencies: 300 W
Cabinet
Handles: 1 on top, 2 on sides
Pole Mount/Cap: yes
Grille: steel
Physical Specifications
Height: 637/25 mm/inch
Width: 384/15.11 mm/inch
Depth: 363/14.2 mm/inch
Net Weight: 20.2/44.53 kg/lbs
|
- 2000W power via ultra-efficient Class-D amplification
- TruSourceTM Technology
- Mackie designed, vertically-aligned, common-magnet TruSource driver
- 12″ LF woofer / 1.75″ HF compression driver
- Incredibly compact, lightweight design
- Powerful TruSource DSP delivers seamless clarity, consistent coverage and unmatched fidelity
- DL2 Integrated Digital Mixer
- Powerful, one-touch digital mixer with bright OLED screen
- Two highly-versatile input channels with FX
- Independent channel level, 3-band EQ and effects control
- 16 great-sounding channel effects include reverb, chorus and delay
- XLR/TRS combo and dual RCA connectors
- Handles mic, line, stereo and instrument signals
- Unmatched system control for professional applications
- Multi-band feedback destroyer
- Six speaker modes deliver the perfect voicing for your application
- Alignment delay up to 300ms for delay stack, balcony, etc.
- Three memory locations for instant venue setting recall
- Smart Protect DSP dynamically protects amp/driver
- Innovative ultra-compact design
- 1/3 smaller than a traditional 2-way
- Fit an entire DLM system in nearly any car
- Stack them up for storage
- Pole-mountable on tripod or atop DLM12S using SPM300 speaker pole
- Flyable via standard M10 rigging hardware
- Wall-mount them using SWM300 articulated arm for stealthy, powerful install system
- Roadworthy PC-ABS cabinet with pro black finish and ergonomic top carry handle
- Rugged, powder-coated 20 gauge steel grille
- Integrated kickstand delivers perfect angle for personal monitor use
- Ridiculously lightweight (31 lbs. / 14.1 kg)
|
Key Features:
- Compact Powered bi-amplified
full-range loudspeaker with JBL
DrivePack® technology for portable or
installed use
- Optimized for both portable/rental or
permanent-venue use
- 1750 watts peak output power,
875 watts continuous
- 12-inch Differential Drive® lowfrequency
driver for extended lowfrequency
output
- Robust powder-coated die cast
aluminum handles, designed for
strength and comfort
- Integrated 35 mm stand mount
Specifications:
Frequency Response (+/-3 dB): 65 Hz - 18 kHz80 Hz – 20 kHz
Frequency Range (-10 dB): 55 Hz - 20 kHz50 Hz – 20 kHz
Coverage Pattern: 90° x 50°
Directivity Factor (Q): 12.6
Directivity Index (DI): 11 dB
Maximum Peak Output1: 134 dB SPL 1m
Transducer Section:
Low Frequency Section: JBL 2262FF, 304 mm (12 in) dia., 76 mm (3 in) Dual Coil
neodymium Differential Drive®, Direct Cooled
Bandpass Nominal Impedance: 2 x 2 ohms
High Frequency: JBL 2452H-SL, 100 mm (4 in) titanium damped
diaphragm, 1.5 in. exit.
Bandpass Nominal Impedance: 8 ohms
System:
DPC1 Internal Amplification Output
(at nominal load) 1750 Watts Peak, 875 Watts Continuous
DPC1 Output (Continuous IEC shaped
pink noise into rated load impedance): 750LF/125HF Watts
DPC1 Output Section: LF: Dual Bridged Technology™, Class D
HF: Bridged Class D
Audio Input connector XLR with loop-through
User Controls: 80 Hz Subwoofer High Pass Filter. Enable/Disable
0-16 dB input Attenuator with 32 precision 0.5 dB steps
Signal Processing: DSP based, resident in Input Module.
System Management: DSP based limiters for mechanical and thermal
protection
AC Power Operating Range: 90-132 VAC/216-264 VAC, 50/60 Hz
AC Line Voltage: 50/60 Hz; User Selectable; 120V/240V (-15%, +10%)
AC Input Connector: Neutrik PowerCon (NAC 3MPA)
AC Loop-thru: Neutrik PowerCon (NAC 3MPB)
AC Current Requirement: 6A per system at 120V, 3A per system at 240V
Enclosure:
Box Construction: 5/8 in. multi-ply exterior grade Baltic birch. Internally
braced. Black DuraFlex™ finish.
Suspension System: 9 M10 Fittings + 2 M6 Fittings, 35 mm pole mount
socket
Grille: 14 Gauge Black powder-coated perforated steel with
foam backing.
Dimensions (H x W x D): 533 x 358 x 334 mm
21.0 x 14.1 x 13.1 in
Net Weight: 21.3 kg (47 lb)
|
- EV QuickSmart Mobile application: quickly and wirelessly configure, control and monitor up to six ELX200 loudspeakers simultaneously, and receive immediate notification during critical performance conditions. Bluetooth® is available in select countries.
- QuickSmartDSP features best-in-class processing. Easy setup via four presets, sub/top system-match, three-band EQ, five user-programmable presets, visual monitoring of limiter status, input level control and meters, and master volume control to optimize gain structure, all via LCD.
- High-efficiency 1200 W Class-D power amplifier delivers up to 130 dB peak SPL utilizing transducers designed and engineered by EV.
- EV-patented Signal Synchronized Transducers (SST) waveguide design provides precise and consistent coverage, minimal distortion, and maximized acoustical loading.
- Professional-grade hardware: three M10 threaded mounting points for forged eyebolts, integrated pole-mounts and the proven ZLX three-handle design for easy lifting.
ELX200-12P features high-efficiency Class-D power amplifiers (up to 1200 W) with integrated QuickSmartDSP, and delivers up to 130 dB SPL utilizing transducers designed and engineered by EV (12-inch EVS-12M woofer coupled with a DH-1C 1-inch titanium compression driver). Powered full-range models allow easy setup via four presets (Music, Live, Speech, Club), sub/top system-match crossovers,
three-band EQ, five user-programmable presets (Store and Recall settings), visual monitoring of limiter status, input level control and meters, and master volume control to ensure optimal gain structure.
ELX200 powered models are ideal for portable and installed applications, with lightweight and durable polypropylene enclosures, three M10 threaded mounting points and the proven ZLX handle design for easy lifting.
The new QuickSmart Mobile wireless control and monitoring application, using Bluetooth® Low Energy (BTLE) technology, allows intuitive system control, configuration and monitoring of up to six powered ELX200 loudspeakers simultaneously. Receive alerts when your system is being overdriven, and control your system while in front of your speakers, not behind. Bluetooth® is available in select countries.
Available Color |
Black |
Connector Type |
(1) Stereo RCA Input, (2) XLR/TRS combo jack, and (1) XLR |
Coverage (Nominal -6 dB) H |
90° |
Coverage (Nominal -6 dB) V |
60° |
Crossover Frequency |
1700Hz |
Depth |
344mm (13.5“) |
Enclosure Material |
Polypropylene Composite |
Family |
ELX200 |
Frequency Range (-10 dB) |
51 Hz – 20 kHz |
Frequency Response (-3 dB) |
57 Hz – 16 kHz |
Grille |
18 AWG steel with powdercoat |
Height |
629mm (24.8“) |
HF Transducer |
DH-1C 1-inch titanium compression driver |
LF Transducer |
EVS-12M 300 mm (12 in) |
Max. SPL/1m (calc) |
130dB |
Power Consumption |
100 - 240 V~, 50 - 60 Hz, 1.8A |
Power Rating |
1200W |
Powered or Passive |
Powered |
Shipping Weight |
17.7kg (39 lbs) |
Speaker Type |
Full-Range |
Suspension |
(3) M10 suspension points |
Weight Net |
15.6kg (34.4 lbs) |
Width |
363mm (14.3“) |
Woofer Size |
12inch |
|
Reviews
There are no reviews yet.