Content |
Headset microphone suitable for item MB504
- Output impedance: 600 Ohm
- Frequency response: 50-12000 Hz
- Connector: 3 poles mini XLR
|
General Specs:
Frequency Response:
| ..... | 20 - 20,000 Hz +/-3dB |
Pick-Up Pattern:
| ..... | Omni-Directional |
Nominal Impedance:
| ..... | 1000 Ohms at 1kHz |
Min. Terminating Impedance:
| ..... | 4.7 K Ohms |
Sensitivity:
| ..... | 2 mV / Pz |
Diameter of Mic Capsule:
| ..... | 4.8mm |
Max. SPL:
| ..... | 150 dB |
Equivalent Noise Level:
| ..... | 28 dB (A) |
Supply Current:
| ..... | 250uA |
Power Supply:
| ..... | 4.5 - 15V |
Cable Length:
| ..... |
1.6 m
|
Diameter of Boom Arm:
| ..... | 1.1 mm |
Weight of Boom Arm:
| ..... | 2.1 g |
Connector:
| ..... | ew Connector |
Weight Neckband:
| ..... | 4.4 g |
| High-quality permanently polarized condenser headmic with omni-directional pick-up pattern, designed for professional "hands free” applications. The adjustable neckband is visually unobtrusive and very comfortable to wear. The twelve available HSP 2 variants differ in color, size and connector.
Τype: |
Headset |
Series Compatibility: |
Εvolution Wireless |
|
Shure WCM16 Headworn Condenser Microphone
The Shure Model WCM16 headworn electret condenser microphone is intended for wireless use by
performers, lecturers, and others who require the highest quality voice pickup with maximum mobility.
Its wide frequency response, low RF susceptibility and reliable operation at temperature and humidity
extremes make the WCM16 suitable for virtually any vocal application. When used with the Shure bodypack
transmitters, the performance of the WCM16 closely resembles the finest conventional vocal microphones.
Miniaturized active circuitry included in the cartridge assembly provides equalization that tailors the low-frequency
response to resemble the warmproximity effect of larger vocal microphones. Because of this low-end response, it
is not necessary to position the microphone directly in front of the mouth, thus avoiding much popping and breath
noise, even without the supplied foam pop screen.
The microphone's hypercardioid unidirectional pickup pattern provides maximum isolation from ambient noise and
from adjacent sound sources such as musical instruments, loudspeakers and other performers. This permits higher
gain-before-feedback without loss or masking of vocals.
Features:
Extra lightweight, adjustable headband stays secure and virtually disappears while being worn
Response comparable to finest conventional vocal microphones
Hypercardioid polar pattern provides maximum isolation from vocalist's own instrument and those of other performers
Uniform polar pattern at all frequencies for maximum gain before feedback
High input clipping level eliminates overload distortion
Cable terminates as 4-pin mini connector
Supplied acoustic foam pop screen
Reliable at temperature and humidity extremes
Specifications:
Frequency Response
50 to 18,000 Hz
Polar Pattern
Hypercardioid, uniform with frequency
Output Impedance
1200 ohms
Output Level (close-talked at 1,000 Hz)
Open Circuit Voltage -55.0 dbV (1.8 mV) at 0.6 m
1 Pascal=94 db SPL
Maximum Sound Pressure Level
150 dB at 1% THD
Dynamic Range
121 dB
Output Noise
29 dB equivalent SPL, A-weighted
Signal-to-Noise Ratio
65 dB at 94 dB SPL
Polarity
Microphone: Positive sound pressure on diaphragm produces positive voltage on pins 3 and 4 with respect to pin 1 (ground) of microphone output connector
Receiver-- 1/4" Phone Jack Output: Positive sound pressure on diaphragm produces positive voltage on tip of receiver 1/4" output connector
Receiver-- XLR Output: Positive sound pressure on diaphragm produces positive voltage on pin 2 with respect to pin 3 of the XLR output connector
Current Drain
0.35 mA
Recommended Operating Voltage
+5 Vdc (positive on pin 2, negative on pin 1)
Environmental Conditions
Operating Temperatures: -18 to 60 degrees C (0 to 140 degrees F)
Storage Temperatures: -29 to 66 degrees C (-20 to 150 degrees F)
Humidity: 0 to 95%
Cable
1.5m (5 ft), small-diameter, shielded, with 4-pin mini connector
Case Finish (Microphone and Headband)
Matte black enamel
Net Weight
36 g (1.27 oz)
|
Shure WCE6LTD Features:
Smallest, lightest, most comfortable microphone of its kind
User-friendly for new and experienced users alike
Excellent for singing and spoken word applications
Extremely popular in houses of worship, theater and broadcast settings
Almost invisible against many skin tones
Rugged, bendable boom assures a custom fit for every wearer
Hands-free, wireless-enabled microphone allows total freedom of movement
Exclusive snap-on cables in 1mm or 2mm diameter for field replacement or compatibility with various wireless systems
Highly resistant to sweat and moisture
High quality voice pickup - more consistent than any lavalier
Excellent rejection of surrounding noise
Reduces feedback in meeting rooms or houses of worship an average of 12dB compared to an omni lavalier
Omnidirectional microphone is virtually immune to wind and breath pops, even without a windscreen
|
Features:
* Head-worn microphone with continuously adjustable behind-the-neck headband
* External shock mount for high mechanical-noise rejection
* Miniature gooseneck for precise positioning near the user's mouth
* Microphone arm provides choice of left or right-hand use
Specifications:
* Polar pattern: cardioid
* Frequency range: 60 Hz to 20 kHz
* Sensitivity: 5 mV/Pa (-46 dBV)
* Max. SPL: 130 dB/132 dB (for THD = 1 %/3 %)
* Equivalent noise level: 31 dB-A
* Signal/noise ratio (A-weighted): 63 dB
* Impedance: = 2000 ohms
* Power requirement: 9 to 52 V phantom power to DIN 45596 or battery powering from B 29 L, or AKG bodypack transmitter
* Connector: C 520: 3-pin male XLR; C 520 L: 3-pin mini XLR
* Cable: C 520: 3 m (10 ft.); C 520 L: 1.5 m (5 ft.)
* Finish: matte black
* Dimensions: length: 195 mm (7.7 in.) (microphone only); max. diameter: 134 mm (5.3 in.)
* Net weight: 26 g (0.9 oz.)
* Shipping weight: C 520: 380 g (13.4 oz.); C 520 L: 260 g (9.2 oz.)
|
Reviews
There are no reviews yet.