| Content | Dual (stereo) hum eliminator
- DATI (dual audio transformer / isolater)
- Frequency range: 10 - 50,000 Hz
- Total harmonic distortion (THD): 0.01%
- 2 Channels
- Inputs: XLR balanced, jack balanced, RCA
- Outputs: XLR balanced, jack balanced, RCA
|
DOD AC 275 Active Direct Box with Switchable Ground Lift and Attenuator-2nd Hand- The AC 275 is an active, phantom powered direct box. Unlike a passive DI where the frequency response of the signal can be altered depending on the connected impedance, an active DI buffers the input signal with an amplifier. This assures that the sound source will reach the mixer balanced and noise-free. Housed in a cast alloy chassis, the AC 275 supplies two, high impedance, unbalanced 1/4" jacks and one low impedance balanced XLR jack. It operates with battery or phantom power.
Key Features
| ?![]() | Active direct box | ?![]() | Allows a hi impedance unbalanced source to directly feed a low impedance balanced input | ?![]() | Flat frequency response | ?![]() | Connects guitar pickups, microphones or electric instruments to a recording or P.A. console without audio quality loss | ?![]() | Internal pad for speaker level input | ?![]() | Operates with battery or phantom power | ?![]() | Ground lift switch eliminates typical ground loop problems | ?![]() | Rugged, road-proof cast alloy chassis |
| Standard active DI box. Can be operated with 9 V batteries or 48 V phantom power. High-impedance input; higher output level than with a passive DI box. Active circuitry allows for high input impedance ( 1 meg. ohm) and higher input sensitivity (typical difference between in and out -4 dB). Maximum output impedance with phantom power operation +10 dB. Output: transformer balanced. The special "floating ground" circuitry enables ground lift even during phantom power operation. Metal case 110 x 73 x 42 mm. |
Phantom or battery powered in a rugged steel chassis
The ARX DI-PLUS 2 represents another major step forward in active direct boxes. Packaged in
a single channel stand-alone format, the DI-PLUS 2 represents a fresh look at active stereo
D.I. concepts.
Precision engineered
Ultra quiet, ultra clean circuitry delivers maximum headroom whatever the signal. Premium grade
components, plus an all-steel chassis gives excellent hum and noise specifications and superb
audio quality in a tough, roadworthy package. Accurate Left and Right channel level matching keeps
the stereo image centred.
Level control
The DI-PLUS 2 features two high impedance unbalanced inputs on the front panel, running to balanced
XLR outputs on the rear. A a global Pad switch drops inputs by 20dB, making it suitable for all applications
from the softest keyboard to the hottest broadcast levels.
Battery compartment
The revolutionary simple 'clamshell' action of the DI-PLUS 2 battery compartment makes battery changing
extremely easy, even on the darkest stages.
A 9v alkaline battery snaps into a PCB mounted battery holder for fast, secure location. No fragile battery clip
leads to break, no tools required, no screws to lose. Production crew heaven!
Automatic Phantom switching
The DI-PLUS 2 will automatically switch itself to the console's own Phantom Power, if available, and an LED
will indicate this mode. Turn the Phantom Power off and it will instantly revert back to battery mode.
Rugged all-steel case
A lot of direct boxes are fitted into brittle cast alloy cases. Not this one! The tough all-steel inner and outer
chassis of the DI-PLUS 2 provide excellent RF/EMF shielding while making it a sturdy, heavy duty unit that
is hard to dislodge, and hard to leave behind.
Rear panel showing Left and Right XLR connectors, ground lift switch, battery check switch and LED, plus
phantom power On LED and captive screw for opening up the unit for battery changing
Whether you're a Studio or Live Sound engineer, installation contractor, or broadcast engineer, you want all
the dynamics,clarity and stereo information of the original sound source transferred to the mixing console.
The ARX DI-PLUS 2 provides a rugged, no-compromise solution to all stereo direct injection and signal
balancing requirements.
T E C H N I C A L S P E C I F I C A T I O N S:
Max Input Level
+12 dB Phantom powered
+6 dB Battery powered
Input Impedance 1 Meg Ohm
Max Output Level
+17 dB 10K Ohm load Phantom powered
+12 dB 10K Ohm load Battery powered
+11 dB 600 Ohm load Phantom powered
+12 dB 600 Ohm load Battery powered
Output Impedance 680 Ohms Balanced
Output Signal to Noise
-100 dB unweighted
-104 dB A weighted
Dynamic Range
117 dB 10K Ohm load Phantom powered
112 dB 10K Ohm load Battery powered
111 dB 600 Ohm load Phantom powered
107.5 dB 600 Ohm load Battery powered
Distortion 100 Hz .0018%, 1KHz .0028%, 10KHz .0056%
Frequency Response 20Hz to 20KHz, ± 0.2 dB
Gain through Unit: 6dB (Pad switch out)
Pad Switch: Global -20 dB attenuation
Input and Loop Out Connectors
Insulated jacks (!!!Note that Channel A Input connector switches the unit on
when a plug is inserted. Remove plug when storing to avoid battery drain!!!)
Output Connectors
3 pin XLR. Wired Pin 1 Ground, Pin 2 + Hot, Pin 3 - Cold.
Global Audio Ground (Pin 1) lift switch
Construction
All-steel chassis, fibreglass PCB
Battery Access
Twist connector opens chassis, snap-in battery holder inside.
No tools required
|
Active DI-Box SM-60
The electronic Direct-Injection Box SM-60 allows direct connection of electronic
music instruments such as keyboards, synthesizers, electric and electronic pianos,
etc. with mixing consoles in PA-systems and in recording studios.
The SM-6 is designed for applications, where a passive DI-Box does not perfom
satisfactorily, i.e., where the output level of a passive DI-Box is too low for the microphone
input section of the mixing desk.
Because the input impedance of the SM-6 is above 5 MOhm, instrument outputs are
not loaded or in any other way adversely affected. The voltage ratio from input to output
is 1: 1 and is always sufficient for connection with any microphone input. Input connectors
are 1/4" phone jacks, output connector is a Switchcraft D3M; output is 600 Ohms,
transformer balanced. The output level may in certain cases overload microphone inputs -
the line input section of the mixing console must then be used for connecting the SM-6.
The unit operates with a 9 V battery or phantom powering from 24 to 48 volts.
Technical Data
input impedance > 5 MOhm
max. input impedance + 6 dBu, 1,55V
ouptut impedance 600 Ohm
frequency response 20 ... 20000 Hz, ± 0,2 dB
gain 1 : 1
THD < 1 % at 30 Hz
< 0,7 % bei 40 Hz
powering 9-V battery (IEC 6LF22) or
phantom power 24 ... 48 V.
inputs two 1/4" phone jacks , unbalanced
(one being used as output to instruments amp)
outputs XLR, balanced
pin 1 = ground, pin 2 = hot, pin 3 = cold
case aluminium die-cast
weight 240 g
dimensions 113 x 71 x 37 mm | Behringer DI-600P High-Performance Passive Direct Injection Box
Introducing the Ultra-Compact DI-Boxes from BEHRINGER
There are times when you will want to connect certain sound sources straight to other audio gear, be it for a live performance or a studio session. A direct connection between audio equipment can be a challenge though: technical problems crop up that?ll corrupt the signal.
The DI600P lets you connect instruments or amplifier outputs of up to 3,000 Watts. It converts any unbalanced signal to a balanced signal and eliminates unwanted noise. With its high-performance transformer, it also allows you to use very long cables without the loss of high frequencies.
This is the sort of medicine that?ll cure headaches in your studio or on stage.
It often happens that you want to connect certain sound sources straight to other audio gear, be it for a live performance or a studio session. The direct connection between audio equipment can quickly turn out to be a real challenge: technical problems crop up that can affect the signal.
Hook Your Guitar or Amp Up to the PA
Be ready for your next gig with the Behringer Ultra-DI DI600P direct box. Designed to send instrument or amplifier signals to the main mixing board, the DI600P is a high-performance passive DI is a useful tool in any gig rig or studio. Dual 1/4" TS jacks are wired in parallel let you plug your instrument into one and use the other as an output to your amp. The balanced XLR mic-level output feeds your mixer a clean and super-flat signal that is true to the source. Sweetwater knows that grounding issues and hum can be a problem at live gigs. The DI600P sports a ground lift switch to kill unwanted ground loops and hum. It also has a filter switch for optimal guitar tone and an instrument/amp switch with a 30dB input level drop. The Behringer Ultra-DI DI600P direct box is an extremely useful tool for any stage rig!
Behringer Ultra-DI DI600P Direct Box Features:
- Compact, high-performance passive direct box
- Jack input 1/4" TS in and parallel out
- Gold-plated XLR output / impedance balanced
- Super-flat frequency output for uncolored sound
- Switchable filter that optimizes the DI for guitars
- Instrument/Amp switch lowers the input level 30dB for feeding amplifiers into the DI
- Instruments or amplifier outputs with up to 3,000 watts can be connected directly
- Offers impedance and signal matching of instruments to mixers
- Perfect for stage and studio use
- Ground lift switch eliminates typical ground loop problems
- Rugged metal case can take the rigors of the road
Get your signal to the board with Behringer\'s Ultra-DI DI600P direct box!
Tech Specs
- Type: Passive DI Box
- Channels: 1
- Ground Lift: Yes
- Inputs: 1 x 1/4"
- Outputs: 1 x 1/4“, 1 x XLR
- Height: 1.4"
- Width: 3.75"
- Depth: 5"
- Weight: 0.66 lbs.
- Manufacturer Part Number: DI600P
|
Reviews
There are no reviews yet.