| Content |
The DigiMAX LT is essential to the modern digital studio. Eight channels of pristine mic
preamplification, inserts on every channel, and an internal power supply set this unit apart
from anything on the market. Each channel features our award-winning, high performance,
dual servo microphone preamplifiers with 48V phantom power, and -20dB pad. Each channel
features a Neutrik?connector that accepts line level or microphone input. DigiMAX LT digital
synchronization is achieved by offering word clock in and out via BNC connectors. The sample
rate can be set on the front panel to 48K, 44.1K, and 32K providing compatibility across multiple
platforms.
The DigiMAX LT provides TRS inserts on every channel to allow external dynamics processors
or equalizers to be placed in the signal chain. The DigiMAX LT is the perfect partner for recording
systems such as DigiDesign 002?, MOTU828, MOTU 2408? as well as numerous digital mixers
and hard disk recorders.
Features
? ADAT? LightPipe Output
? Eight Dual Servo Mic Preamps and Line Inputs
? Eight TRS Insert Points
? Linear Internal Power Supply
? 48V Phantom Power on Each Channel
? -20dB Pad on Each Channel
? Adjustable Sample Rates
? BNC I/O for Sync
Technical Specifications
Number of Channels Eight
Input
Input Impedance, XLR Input 1.3k Ohms
Input Impedance, Line Level Input 10k Ohms
Connectors Neutrik? Combo
Panel Controls
Gain 0dB to +40dB
Pad -20 dB
Phantom Power +48 V
Meters
Signal Present LED -20dBu
Clip LED +22dBu
Output
ADAT? LightPipe Digital Optical 24-bit
Insert (TRS)
Send (Unbalanced) 51 Ohms
Return (Unbalanced) 10k Ohms
Digital
Sampling Rates 32kHz, 44.1kHz, 48kHz
Performance
Headroom +22dB
Frequency Response 20Hz-50kHz
THD + Noise (Unweighted) 98dB
Analog Dynamic Range >120dB
Power Supply Rejection >98dB
Amplifier Type Dual Servo
Power Supply
Type Linear, Internal Input: 100/120/220/240V AC (Factory Configured)
Power 80 Watts
Physical
Size 1U Rack
Dimensions 19" x 1.75" x 9“
Weight 10 lbs./ 4.5 kg.
Chassis Steel
Panel Aluminum
|
The PreSonus HP60 is the most flexible and advanced headphone amplifier system available for professional and project recording studios as well as live sound in-ear monitoring systems. Loaded with six independent,
loud and clear headphone amplifiers, the HP60 features dual stereo inputs as well as external input, for each
channel allowing you to mix between three stereo audio streams (mix A, mix B, and external input). Stereo output is also available on each channel to send line level headphone channel mixes to additional headphone amplifiers or monitor systems. Each channel features headphone level, mix control between A and B inputs, external input volume, mute and mono. The HP60 also features talkback via external XLR microphone input. Common set up of the HP60 in a recording session is to send the main control room mix to input A. Send the click track to input B. Send the each band member direct recording input to each channelʼs external input (more me). This will allow each band member to create a mix between the main mix, the click track and themselves. The HP60 is the ultimate headphone amplification system delivering loud and clear headphone mixes for real-world recording situations.
Features:
-Six independent ultra low noise, high output headphone amplifiers (150 mW per channel)
-Two sets of stereo inputs (A and B) with balanced TRS connectors
-Stereo external input point on each channel for "more me” with trim control
-Mix control between inputs A and B
-Talkback with external XLR microphone with control
-Direct stereo line output on each channel
|
Input A
|
(2) ¼” TRS balanced 10 Ohms
| |
Input B
|
(2) ¼” TRS balanced 10 Ohms
| |
External input
|
TRS stereo unbalanced 10 Ohms
| |
Headphone amplifier output power
|
150 mW RMS (60 Ohms) per channel
| |
Audio outputs
|
¼” TRS stereo unbalanced per channel
| |
Master controls
|
Talk button, Talkback volume, Input A, Input B
| |
Channel controls
|
Headphone level, Mix A/B control, External input level, Mono, Mute
| |
External talkback
|
XLR with TS external control jack
| |
Power
|
IEC 110V-240V internal switching
|
|
- 1 microphone, XLR (bal.) or 6.3 mm jack (unbal.)
- Gain control, 10 steps (6-50 dB)
- Phantom power can be switched on
- Clip LED
- 1 line output, XLR (bal.) or 6.3 mm (unbal.)
- Operation via supplied power unit
| Power supply: | 12 V DC, 150 mA | | Input impedance: | 10 kohms bal./unbal. | | Max. input level: | +4 dB bal./+10 dB unbal. | | Gain: | 50 dB XLR/44 dB jack | | T.H.D.: | 0.01 % | | Frequency range: | 25 Hz - 16 kHz | | S/N ratio: | >75 dB | | Dimensions: | 143 x 93 x 45 mm | | Weight: | 350 g |
|
The U5 high-voltage DI-preamp combines a unique passive tone selector with a variable
gain preamp and filter. The high input impedance accepts a wide variety of signal levels
and instruments from acoustic guitars to high-output active bass guitars and keyboards.
The U5 direct box is loaded with sonic character and user features professionals demand.
U5 FEATURES
Pure Class A, 100% discrete design
Smooth musical detail and sonic excellence
Variable gain preamp to +30dB.
Dual microphone and line outputs
Hi-Z 3,000,000 ohm input impedance
Very low noise -100dB
High headroom +30dB
Six tone bank selections.
DC coupled Class A output for superior bass
High cut switch eliminates noise
LED active signal indicator
Headphone monitor output jack
Low distortion less than 0.5% THD and IMD
High level 400 watt speaker input
Active to thru selector - ground isolation switch
100% discrete power supplies for audio path
Internal toroidal power supply for low noise
Long lasting, stainless steel hardware
SONIC EXCELLENCE
The Avalon U5 Pure Class A instrument DI & preamplifier is the most powerful direct box
available today. Designed to optimize absolute signal integrity and musical performance,
the U5 includes many features and sonic excellence unequaled by lesser designs. The
U5 is ideal for bass guitar and acoustic instruments, electric guitars, keyboards, synthesizers
and low output pickups.
Features include state-of-the-art, high input impedance input stage for zero load effect on
sensitive pickups and keyboards, 100% discrete, Pure Class A signal amplifiers, practical
user features and rugged hardware designed to deliver true high performance audio for many
years.
DESIGNED FOR DEEP & CONTROLLED BASS
Avalon U5 DI-preamps have been in use around the world since 1995. They have found their way
into the world's leading musicians rigs and recording sessions and been featured on thousands
of the best selling (and sounding) albums and live performances.
MINIMUM SIGNAL PATH DESIGN
The U5 includes a variable gain Class A preamplifier to boost low level pickup signals and a high
level speaker input for capturing the live sound of the instruments amplifier. Six passive tone-EQ
curves are also included to enhance a variety of acoustic and electric instruments. A high-cut switch
eliminates unwanted acoustic pickup and high frequency noise, while a headphone monitor amp
has been included for personal listening. Twin DC coupled Class A output amplifiers drive both low
level microphone preamp inputs and high level +4dB inputs for direct to tape recording or processing.
The active-to-thru switch selects either the instrument input directly or sends the boosted-equalized
signal to the amplifier via the front panel jack. A ground isolation switch eliminates any possible earth
loop or AC buzz problems with complete safety.
U5 SPECIFICATIONS
Circuit Topology: 100% discrete, high-voltage Class A
Gain: Switched 3dB steps, maximum gain +30dB
Input Impedance: 3 ,000,000 ohm unbalanced (single ended)
Maximum Input Level +24dBu unbalanced, 400w speaker input
Output Connectors (2): XLR type, pin 2 hot electronic balanced
Maximum Output Level (Class A): +30dBu DC coupled, balanced 600 ohms (mic and line out)
Headphone Output: 0.5w into 600 ohms
Noise 20kHz Unweighted: -100dBu minimum gain position
Distortion THD, IMD: 0.1% at +10dB
Frequency Response, -/+0.5dB: 5Hz to 100kHz
Frequency Response, -3dB: 1Hz to 500kHz (input band limited)
High Cut Filter: -3dB at 8kHz minimum phase design
Tone Selector: Six position rotary switch, all passive filters
AC Power: Internal toroidal AC supply
Dimensions: 8.5 x 3.5 x 12 in (216 x 88 x 305mm)
Weight-Packed: 12lbs (5.4kg)
Rack mount kit (1) RM-1: Single U5 19 inch rack mount kit (holds one half rack unit)
Rack mount kit (2) RM-2: Dual U5 19 inch rack mount kit (holds two half rack units)
| ISA OneClassic Single-channel Microphone Pre-amplifier with Independent D.I.
Key Features
ISA Series Transformer-based Pre-amplifier
Encased in a rugged and portable chassis, ISA One offers the classic Focusrite microphone pre-amplifier at its lowest cost to date.
Flexible Independent D.I. Channel
ISA One is ideal for both engineers and demanding performers alike, featuring independent gain control, an output for routing to an amp, an independent XLR output on the rear and routing to the optional ADC.
Switchable Impedance
Choose one of four carefully selected input impedances, including the original ISA 110 setting, to suit any microphone.
Optional Stereo 192kHz ADC
This optional card embodies cutting-edge conversion technology, incorporating Focusrite analogue circuitry to deliver the best A-D performance in its class (Dynamic range of 119dB).
Rugged Custom Flight Case
Built to protect your ISA One from the rigors of the road. Rugged plywood construction with a solid polypropylene exterior and reinforced corners.
Headphone Output with Volume Control
ISA One can feed either a sum of the two inputs to the headphones output, or an external stereo cue mix (such as a stereo mix feed from an interface) via two TRS Jack inputs on the rear of the unit.
Dedicated Insert Point
Allows you to place extra processing between the pre-amplifi er or D.I. and the optional converter, such as an EQ or compressor.
Specifications
Analogue Channel Inputs
- XLR Mic input
- One XLR and one TRS line input
- XLR Instrument input TRS Jack
- External ADC input TRS Jack
- TRS jack return
|
Analogue Channel Outputs
- TRS jack send
- XLR balanced line output
- XLR DI output
- TS jack DI through
|
Analogue Channel Additional I/O
- TRS Jack cue mix left input
- TRS Jack cue mix right input
- 1/4” TRS Jack headphones output
|
Mic Input Response
| Gain range |
0dB to 60dB in 10dB steps + 20 dB of variable gain |
| Input Impedance |
Switched Impedance setting Equivalent Input Impedance at 1kHz |
Low = 600 Ohms
ISA110 = 1400 Ohms
Med = 2400 Ohms
High = 6800 Ohms |
| EIN (Equivalent Input Noise) |
-126dB measured at 60dB of gain with 150 Ohm terminating impedance and 22Hz/22kHz band-pass filter |
| Noise |
Noise at output with unity gain (0 dB) and 22 Hz-22 kHz band pass filter |
-97 dBu |
| Signal-to-Noise Ratio |
106 dB relative to max headroom (9dBu) |
| Total Harmonic Distortion + Noise |
Measured at medium gain (30dB) with a 1kHz -20dBu input signal and with a 22Hz/22kHz band-pass filter |
|
| Frequency Response |
At minimum gain (0 dB) |
-0.5dB down at 10Hz and -3dB down at 125kHz |
|
At maximum gain (60dB) |
-3dB down at 16Hz and -3dB down 118kHz |
| CMRR (Common Mode Rejection Ratio) |
98dB (Channel 1, 1kHz, maximum gain with +24 dBu input) |
| Crosstalk Channel to Channel |
With 10dB@1kHz input to chA, chB output =104dBrA. With 10dB@10kHz input to chA, chB output = 84dBrA |
Line Input Response
| Gain range |
-20dB to +10dB in 10dB steps + 20 dB of variable gain |
| Input Impedance |
10 kΩ from 10 Hz to 200 kHz |
| Noise |
Noise at main output with gain at unity (0 dB) measured with 50 Ω source impedance and a 22Hz - 22 kHz band pass filter |
-96 dBu |
| Signal-to-Noise Ratio |
Measured with a 22 Hz-22 kHz band pass filter |
120 dB relative to max headroom (24 dBu)
118dB relative to 0dBFS (+22dBu) |
| Total Harmonic Distortion + Noise |
Measured with a 0 dBu input signal, and a 22 Hz-22 kHz band pass filter |
0.0001% |
| Frequency Response |
At unity gain (0 dB) |
-0.3dB down at 10Hz and -3dB down at 200kHz |
Instrument Input Response
| Gain range |
10dB to 40dB continuously variable |
| Input Impedance |
High = greater than 1M
Low =greater than 300k |
| Noise |
Measured with 22 Hz-22 kHz band pass filter |
Minimum gain (+10 dB): -92 dBu
Maximum gain (+40dB): -62dBu |
| THD |
At minimum gain (+10) |
| Frequency Response |
At minimum gain (+10 dB) |
-10dB input: 10Hz-100kHz +/- 0.6dB |
|
At maximum gain (+40 dB) |
-40dB input: -2.5dB down at 10Hz and 0dB at 100kHz |
Meters
| Moving Coil (MC) Meter |
factory calibrated to 0VU = +4dBu with 1kHz sinewave. With the VU Cal button pressed the meter can be adjusted on the rear panel to allow 0VU to equal +10dBu to +26dBu with the centre detent being equal to +22dBu. |
| Peak LED Meters |
Calibrated in the detent position for 0dBFS = +22dBu, calibration is adjustable on the rear panel to allow 0dBFS to equal +10dBu to +26dBu |
| Routing for MC and Peak1 meter is after the HPF, pre insert send or switched post insert return. Peak2 is always pre ADC channel 2, which can be fed by external input or Instrument input. |
| LED Levels |
As follows, when peak calibration is set to center detent on the rear panel. (This is when using the internal ADC). |
0 = +22dBu
-2 = +20dBu
-6 = +16dBu
-12 = +10dBu
-18 = +4dBu
-42 = -20dBu |
| Frequency Response |
At minimum gain (+10 dB) |
-10dB input: 10Hz-100kHz +/- 0.6dB |
|
At maximum gain (+40 dB) |
-40dB input: -2.5dB down at 10Hz and 0dB at 100kHz |
High-Pass Filter
| Roll-Off |
18 dB per octave (3 pole filter) |
| Frequency |
Fixed 75Hz measured at the 3dB down point |
Weight and Dimensions
| W x D x H |
220mm (W) x 104mm (H) x 254 - 290mm (D - top to bottom) |
8.66" (W) x 4.1" (H) x 10" - 11.4" (D - top to bottom) |
| Weight |
3.9 kg |
8.6 lbs |
|
Designed for high-definition field production environments, the studio-quality MP-1 is an ideal line-driver for critical radio, television, and film applications.
The MP-1 is extremely durable and easy to use. With rugged mechanical and electrical construction and high-quality components it will provide years of superb audio performance under the most punishing field conditions.
MP-1 Key Features - Superb audio specifications
- 66 dB of gain, in eleven discrete steps
- Transformer-balanced input and output
- Phantom power - 48 volt or 12 volt
- High pass filter @ 80 Hz or 160 Hz, 6 dB/octave
- Limiter makes unit virtually "unclippable“
- High current line output drive
- Excellent immunity to RF interference.
- Battery power (two x AA)
- Durable mechanical construction
|
Reviews
There are no reviews yet.