| Content | The PRM1 Precision Reference Microphone is a special type of condenser microphone that provides an accurate reproduction of a room's sound characteristics for use with audio-analysis tools such as real-time analyzers (RTAs) and spectrographs.
- ¼-inch, pre-polarized electret-condenser capsule
- Linear frequency response between 20 Hz and 20 kHz
- Omnidirectional polar pattern
- Low noise, low distortion
- All-metal chassis
- Comes with a clip, foam windscreen, and hard case
- High-quality components and rugged construction
- Suitable for system analysis and measurement
- Especially recommended for use with PreSonus StudioLive mixers and VSL with Smaart® Measurement Technology
| General Specifications |
| Type |
Black electret condenser |
| Element |
Pressure, FET preamplifier |
| Polar Pattern |
Omnidirectional |
| Connections |
| Polarity |
Pin 2 output positive voltage (relative to Pin 3) when diaphragm receives positive pressure (moves inward) |
| Connector |
3-pin XLR Male |
| Performance |
| Frequency Response |
20 Hz to 20 kHz |
| Sensitivity (@ 1 kHz open-circuit voltage) |
-37 dB/Pa (14 mV/Pa) 1 Pa=94 dB SPL |
| Rated Impedance |
200Ω |
| Minimum Load Impedance |
1,000Ω |
| EIN (A-weighted) |
26 dB |
| Max. SPL (1 kΩ load) |
132 dB SPL (THD ≤ 1%, 1 kHz) |
| Dynamic Range (1 kΩ load) |
106 dB |
| S/N Ratio |
70 dB |
| Power |
| Phantom Power |
9-52V |
| Current Consumption |
2 mA |
| Physical |
| Length |
7.56" (192 mm) |
| Width |
0.83" (21 mm) |
| Weight |
5.3 oz (150g) |
| Finish |
Metal, matte black |
| Environmental Conditions |
10-50˚ C, humidity 0-95% |
| The NT5 matched pairs are a masterpiece of small-diaphragm cardioid-
condenser microphone design.Intended for recording acoustic instruments,
drum overheads, cymbals and live performances, the compact externally
polarized mic employs a .5? capsule, an active J-FET impedance converter
with bipolar output buffer.
Finished in durable satin nickel, the NT5 is intended for either single or stereo
X/Y mic set-ups. The NT5 matched pairs comesupplied in a custom carry case
with windshields and mounts.
SPECIFICATIONS:
Acoustic principle: Externally polarised single diaphragm
Directional pattern: Cardioid
Frequency range: 20Hz - 20kHz
Output impedance: 100?
Signal noise ratio din iec 651: 78dB
Equvalent noise: Maximum spl: 143 dB @ 1% THD into 1k_
Sensitivity:
-38 dB re 1v/Pa ± 2 dB equivalent to 12mV/Pa where 1 Pa = 94dBSPL
Power supply voltage: P48 Supply (38V?52V), P24 Supply (20V-26V)
Current consumption: 4 mA, 2 mA,
Weight: 100g |
The R?DE NT6 is specifically designed for difficult mounting applications. Although
clearly relevant to instrument mic'ing, the new NT6 is extremely well suited to any
situation where a small 'unobtrusive' but powerful microphone system is required.
The NT6 utilises the 1/2" (externally biased) gold sputtered true condenser transducer
used in the internationally renowned R?DE NT5. The capsule is designed to attach to
a custom made, multi-position swivel mount allowing it to be independently positioned
with ease.
To further increase the versatility of the NT6, it is supplied with 2 thread adaptors - 1/4"
to 5/8" and 1/4" to 3/8" that enable the capsule assembly to be securely attached to a
wide variety of mic stands, tripods and boom poles.
The capsule is connected to the pre-amplifier (body) by a custom 3 m Kevlar? fibre reinforced
cable. Housed within the heavy duty satin-nickel-plated body, is a state-of-the-art low noise
balanced output preamplifier, exhibiting a wide dynamic range and full frequency response.
The surface-mount pre-amplifier circuit also incorporates a 2-position variable pad: 0 dB an -10 dB
attenuation, and a 2-position variable high-pass filter that enables you to step from a flat response
to 80 Hz high pass filter; both conveniently located away from the capsule, providing additional
control without the need to move the capsule once in position.
The NT6 is intended for Film, Television, Broadcast, Live Performance, Theatre, Television,
Surround and Environmental recording applications or wherever your imagination takes you.
The NT6 is produced in R?DE's design and manufacturing facility in Sydney, Australia. Utilising
state of the art computer controlled machining and assembly technologies, R?DE is able to
achieve levels of finish and repeatability of the most exacting standards and tolerances.
The NT6 comes supplied with Microphone Preamp (Body), Capsule, 3 m Kevlar? fibre reinforced
cable, RM5 Stand Mount, 2-axis Swivel Mount, 2 thread adaptors, ZP1 Zip Pouch and WS5 Wind Shield.
FEATURES:
? 1/2? (externally biased) gold sputtered true condenser capsule ? Heavy duty satin-nickel-plated body
? 2-position variable pad: 0 dB and -10 dB ? 2-position variable high-pass filter: flat and 80 Hz ? Surface
mount technology ? Low noise ? Wide dynamic range ? Full frequency response ? Supplied complete
with 2-axis swivel mount, 2 thread adaptors, M5 clip, WS5 (Black) Wind Shield and Soft Pouch ? Designed
& manufactured in Australia ? Full 2 year guarantee
Operation power:
The NT6 is designed to operate from phantom power to the P48 standard. The NT6 will operate
between 44V and 52V applied with positive polarity to pin 2 and pin 3 of the output XLR connector.
Operation output impedance:
Output Impedance: The NT6 will operate satisfactorily into a load impedance as low as 1 kΩ. If a
load below this is used, the output signal level will be reduced. The NT6 output is balanced between
pin 2 (hot) and pin 3 (cold). Pin 1 is ground.
Acoustic principle:
Externally polarised 1/2" (13mm) pressure gradient condenser
Directional pattern: Cardioid
Frequency range:
40 Hz ~ 20,000 Hz selectable HPF @ 80 Hz/12 dB/octave
Output impedance: 200 Ω
Signal noise ratio din iec 651:
75 dB (1 kHz rel 1 Pa; per IEC651, IEC268-15)
Equvalent noise: 19 dB SPL (per IEC651, IEC268-15)
Maximum spl:
138 dB (@ 1% THD into 1 kΩ)148 dB (@ 1% THD into 1 kΩ) - pad at maximum
Sensitivity:
-38 dB re 1 Volt/Pascal (16 mV @ 94 dB SPL) +/- 2 dB
Dynamic range din iec 651: 119 dB (per IEC651, IEC268-15)
Power supply voltage: 48 Volts (P48)
Weight: 386 grm.
Maximum output voltage: 6 dBu (@ 1% THD into 1 kΩ)
Pin assignment:
3 pin XLR, balanced output between pin 2(+), pin (-) & pin 1 (ground)
|
The Shure Model VP88 is a single-point, stereo condenser microphone for use in professional studio recording, field production, electronic news gathering (ENG), and studio broadcasting applications. It combines two condenser cartridges in a single housing to create a stereo audio image of the sound source. It is unique in its ability to capture the realism of a live event and yet withstand rigorous field production environments.
The VP88 uses a mid-side (M-S) configuration. One microphone cartridge (Mid) faces forward to capture on-axis sound using a cardioid pickup pattern. The other microphone cartridge (Side) is bi-directional, capturing sound from either side. The VP88 contains an internal M-S matrix with three settings for different degrees of stereo image seperation. The internal matrix can be bypassed if an external matrix is used or if stereo imaging is done in post-production. Switches on the top of the microphone control output mode, stereo imaging, low-frequency rolloff settings, and battery on/off.
The VP88 can operate on phantom power or an internal 6V battery. The VP88 is supplied with a multi-connector "Y-splitter" cable, foam windscreen, swivel stand adapter, 6-volt battery, and zippered carrying/storage bag. Optional accessories include an isolation mount, a 7.6 m (25 ft) microphone extension cable, a phantom power supply, and a 4.3 m (14 ft) microphone stand.
- Time-coherent, Mid-Side (M-S) design for optimal stereo imaging
- Built-in stereo matrix for direct control of the stereo spread; direct M-S outputs available
- Mono compatibility ideal for broadcast applications
- 40 to 20,000 Hz frequency response
- Low noise and distortion
- Wide dynamic range
- Switch-selectable, low-frequency rolloff (12 dB/octave below 80 Hz) for reduced pickup of ambient noise and stand vibration
- Operates on phantom power or a 6V camera battery
- LED power indicator
- Internal shock mount for reduced stand vibration and handling noise
- Built-in "pop" screen
- Includes windscreen, swivel adapter, and Y-cable
|
MC10M is a multi capsule microphone set including a cardioid electret condenser microphone
(MC10) with the replaceable super cardioid capsule, shock mount adaptor, and wind screen.
MC10M can be used in wide applications, from studio & home recording to field sound aquisition.
FEATURES:
Replaceable 2 types of polar pattern capsule, cardioid/super cardioid as standard
Wide frequency response range
High sensitivity
Low distortion
High input withstand S.P.L.
Rugged brass case
Light weight
Shock mount adaptors, stereo mounting blacket & wind screen as standard
Dedicated carrying case as standard
SPECIFICATIONS:
Type :Back Electret
Condenser Microphone
Polar Pattern :Cardioid/Super Cardioid
Frequency Response :40Hz to 20kHz +/-10dB
Sensitivity :-40dBV/pa (10mv/pa)
Rated Impedance :200W
Equivalent Noise Level
:22dB (A weighted IEC/DIN 651)
Maximum S.P.L. :134dB (THD£0.5%, 1kHz)
Dynamic Range :112dB
Power Supply :48V Phantom Power
(IEC 268-15/DIN45596)
Current Consumption :3.5mA
Dimensions :?20mm x 150mm
Net Weight :130g (MC10 x 1)
Full Package Weight :865g
|
8 Wide frequency response range
High sensitivity, Low distortion
High input withstand S.P.L.
Rugged brass case, Light weight
Shock mount adapters, stereo mounting bracket and wind screens as standard
PREMLIMINARY INFORMATION.
The MC10ST is a stereo microphone set including a pair of cardioid electret condenser microphones,
shock mount adapters, stereo mounting bracket and wind screens. The MC10ST can be used in a
wide range of applications, from studio and home recording to field or location sound aquisition.
Wide frequency response range
High sensitivity
Low distortion
High input withstand S.P.L.
Rugged brass case
Light weight
Shock mount adapters, stereo mounting bracket and wind screens as standard
Dedicated carry case as standard
SPECIFICATIONS:
Type: Back Electret Condenser Microphone
Polar Pattern: Cardioid
Frequency Response: 40Hz to 20kHz +/-10dB
Sensitivity: -40dBV/pa (10mv/pa)
Rated Impedance: 200ohm
Equivalent Noise Level: 22dB (A weighted IEC/DIN 651)
Maximum SPL: 134dB (THD |
Reviews
There are no reviews yet.