Content |
Double-Brace, Low Profile Stand for Large Amps
and Combos
Height adjustment range
Front tier: 8.25" to 11" - 21 to 28 cm
Back tier: 11.4" to 18.6" - 29 to 47.2 cm
Width: 19.3" - 49 cm
Folded height: 22" - 56cm
Frame tube size: 20 x 15 mm
Tier tube size: 28mm
Weight capacity: 100lb - 45.2 kg
Weight: 6.6 lb - 3 kg
|
"When I run my guitar into two amps simultaneously, I always get a loud hum". This is a rather common problem, often discussed in the technology section of relevant industry magazines. The Palmer Y box is the solution. Converting the hi-Z guitar signal, the FET input circuitry also drives a transformer which routes the ungrounded signal to the output to eliminate ground loop hum. 9V battery operation is recommended.
The PGA03 Y-box can also be used as a line driver for long cable runs. Also, the PGA03 features a phase reverse switch for the AMP 2 output when using pre-amps or amps that are out of phase.
Technical specifications:
Input connectors
6.3 mm jack
Number of split-outputs per canal
1
Output connectors
6.3 mm jack
Transformer isolated outputs
Yes
Controls
ground lift, phase
Operating voltage
9 V block, 9 V DC power supply
Cabinet material
sheet steel
Cabinet surface
Powder coated
Optional Power Supply PW9V |
Description
The GS 08 WMB is a universal wall mount hanger for acoustic, electric and bass guitars. The yoke is self adjusting to accommodate any headstock. It is coated with specially formulated rubber that provides a secure grip and does not mar the finish.
Not recommended for guitars with nitro laquer.
Specifications
- Universal wall mount guitar hanger
- Self adjusting yoke
- Specially formulated rubber coating
- Interchangeable colour coding ring
- Material: steel/plastic
- Colour: Black
- Surface: rubber coated
- Suitable for: acoustic guitars , bass guitar , electric guitar
- Number of guitars: 1
- Weight: 0,168 kg
|
Also available as 2, 4 and 16 Ohm Versions
Special DI box with loadbox for guitars. The integrated load resistor permits tube amplifiers up to approximately 120 W to be connected to the PGA04, bypassing a loudspeaker. A jack socket (unbalanced) and balanced XLR connector are available for direct pickup of the signal. The extensive filter section provides for a realistic simulation of classic guitar loudspeaker sounds.
Technical specifications:
- Loadbox: 6.3 mm jack input with parallel THRU socket for speaker operation Loadbox
- Input impedance: 8 ohms, max.
- Input load: 120 w RMS
- Input level display: 6 LED's
- Output: 2 x 6.3 mm jack, unbalanced, floating ground, 1 x balanced XLR output
- Output impedance: jack: 10.000 ohms, XLR: 600 ohms
- Level: unbalanced 0 dB, balanced -10 dB at 25 w
- Input Controls: Volume FiIlter, LOW, HIGH, LITE/BROWN-switch for tone shaping
- Full Range Volume for unfiltered signal, used in conjunction with the HI-CUT to emulate the bright sound of, e.g., 10-inch speakers
- Both signals attenuable
| Adjustable drum stool, diameter 280mm
Drums seat adjustable in height (500mm-630mm), Anatomical round saddle with a diameter of 280mm, Tube diameter: 28.6mm/25mm, Legs double reinforced with anti-slip protectors at the ends. |
Large amp "X” stand with adjustable back tier Adjusts so that the back tier rests on the back panel of open back guitar amps/combos and does not enter the empty space This unique design assures no damage to tubes or electronics Αpplication: | Amplifier | Type: | Adjustable | Type: | Single |
|
Reviews
There are no reviews yet.