| Content |
Double-Brace, Low Profile Stand for Large Amps
and Combos
Height adjustment range
Front tier: 8.25" to 11" - 21 to 28 cm
Back tier: 11.4" to 18.6" - 29 to 47.2 cm
Width: 19.3" - 49 cm
Folded height: 22" - 56cm
Frame tube size: 20 x 15 mm
Tier tube size: 28mm
Weight capacity: 100lb - 45.2 kg
Weight: 6.6 lb - 3 kg
|
"When I run my guitar into two amps simultaneously, I always get a loud hum". This is a rather common problem, often discussed in the technology section of relevant industry magazines. The Palmer Y box is the solution. Converting the hi-Z guitar signal, the FET input circuitry also drives a transformer which routes the ungrounded signal to the output to eliminate ground loop hum. 9V battery operation is recommended.
The PGA03 Y-box can also be used as a line driver for long cable runs. Also, the PGA03 features a phase reverse switch for the AMP 2 output when using pre-amps or amps that are out of phase.
Technical specifications:
Input connectors
6.3 mm jack
Number of split-outputs per canal
1
Output connectors
6.3 mm jack
Transformer isolated outputs
Yes
Controls
ground lift, phase
Operating voltage
9 V block, 9 V DC power supply
Cabinet material
sheet steel
Cabinet surface
Powder coated
Optional Power Supply PW9V |
The concept behind the cab merger may be very simple, but it fills an important gap!
Have you ever wanted to connect two guitar cabinets to one amplifier output? The PCABM makes it possible.
In addition, you can select whether the cabinets should be wired in parallel or series with one another. For example, if you interconnect two 8 ohm cabinets. The PCABM offers you two resulting impedances to choose from: 4 ohms (parallel) or 16 ohms (serial). The device is passive and does not affect the tone in any way.
- Type: passive
- Number of inputs: 2
- Input connections: 6.3mm jack
- Number of outputs: 2
- Output connections: 6.3mm jack
- Cabinet material: die-cast aluminium
- Case surface: powder-coated
- Width: 105 mm
- Depth: 35 mm
- Height: 35 mm
|
Also available as 2, 4 and 16 Ohm Versions
Special DI box with loadbox for guitars. The integrated load resistor permits tube amplifiers up to approximately 120 W to be connected to the PGA04, bypassing a loudspeaker. A jack socket (unbalanced) and balanced XLR connector are available for direct pickup of the signal. The extensive filter section provides for a realistic simulation of classic guitar loudspeaker sounds.
Technical specifications:
- Loadbox: 6.3 mm jack input with parallel THRU socket for speaker operation Loadbox
- Input impedance: 8 ohms, max.
- Input load: 120 w RMS
- Input level display: 6 LED's
- Output: 2 x 6.3 mm jack, unbalanced, floating ground, 1 x balanced XLR output
- Output impedance: jack: 10.000 ohms, XLR: 600 ohms
- Level: unbalanced 0 dB, balanced -10 dB at 25 w
- Input Controls: Volume FiIlter, LOW, HIGH, LITE/BROWN-switch for tone shaping
- Full Range Volume for unfiltered signal, used in conjunction with the HI-CUT to emulate the bright sound of, e.g., 10-inch speakers
- Both signals attenuable
|
Practical, easy to use and stable stand for Eb alto saxophones. Solid square-type aluminum tubes with a large central locking screw, protective rubber bumps where the stand connects with the saxophone body and the bell. Embedded foot end caps. Folds compactly, can be transported in the supplied velour bag in the saxophone bell.
- Weight: 0.3 kg
- Height: 310 mm
|
The PMBL-ACTIVE is a 2-channel stereo line level merge box that can be used to merge two stereo line signals into one stereo output. One classic application: routing two mixing desks to one PA system. The unit has enough amplification to boost even semi-professional levels accordingly. The input channels are galvanically isolated from one another. Each channel offers a mute switch and the ability to mix the stereo signal down to mono. The unit is housed in a 1 U/9.5" case and has a built-in power supply.
|
Reviews
There are no reviews yet.