Content |
This professional stereo power amplifier, working in class-H mode, provides 2x1600W, at an efficiency of around 85%.
A massive transformer based power supply and hand selected components makes this power rating possible with exceptional audio quality and absolute reliability, even in the 2 Ohm mode.
The output stage is fully protected against over-temperature, short circuit, RFI and equipped with soft start circuit and temperature-controlled fan cooling.
The integral soft clip limiter protects against damage to the connected loudspeakers.
The activity of a protective circuit, signal and limiter is shown for each channel by LEDʼs.
AMPLIFIER SPECIFICATIONS |
---|
Power output stereo 2Ω: | 2 x 1600 Watt rms | | Power output stereo 4Ω: | 2 x 1100 Watt rms | | Power output stereo 8Ω: | 2 x 700 Watt rms | | Power output bridged 4Ω: | 3200 Watt rms | | Power output bridged 8Ω: | 2200 Watt rms | | Frequency Response: | 20 Hz ÷ 20 kHz | | Signal/noise rate: | > 102 dB | | Crosstalk: | > 65 dB | | Distortion (THD+N): | | | Intermodulation: | | | Damping factor: | 400:1 (8 W) | | Slew rate: | 50 V/μS | |
INPUT SECTION |
---|
Input connector: | 2 x XLR balanced, 6,3mm jack unbalanced | | Input sensitivity: | 0 / 0.775 dBm/V RMS | | Input impedance: | 20.000 kΩ | | Controls: | Volume control for each channel | |
OUTPUT SECTION |
---|
Output connector: | 2 x Neutrik Speakon 4 ways | |
SYSTEM PARAMETERS |
---|
Cooling: | Two-speed fan | | Protections: | Thermal, temperature, direct current, short circuit, RFI | |
POWER REQUIREMENT |
---|
Operating voltage: | 220÷240 / 110÷120 ~ 50 / 60 V ~ Hz | | Max.current: | 16 A | | Power Consumption: | 6500 W | |
PHYSICAL SPECIFICATIONS |
---|
Height: | 132 / 5.19 mm/inch | | Width: | 483 / 19.01 mm/inch | | Depth: | 455 / 17.91 mm/inch | | Net Weight: | 29.5 / 65.03 Kg/Lbs | |
SHIPPING INFORMATION |
---|
Package height: | 200 / 7.87 mm/inch | | Package width: | 575 / 22.63 mm/inch | | Package depth: | 555 / 21.85 mm/inch | | Shipping Weight: | 32.5 / 71.64 Kg/Lbs |
|
Crown DSi 4000 2x1200W-4Ω Power Amplifier
The Crown? DSi 4000 power amplifi er shall be a solid-state two-channel model
with a switch-mode universal power supply. A rear-panel HD-15 connector shall
provide input/output connectivity between the DSi amplifi er and the DSi-8M
System Monitor.
The outputs shall be usable as stereo or bridged-mono modes of operation.
The bridged-mono mode shall bridge the outputs to provide increased output
voltage.
Front panel controls and indicators shall include the following:
Level: Detented rotary level control, one per channel.
Power Switch: On/off switch applies AC power to the amplifi er.
Sel/Prev/Next Buttons: Three buttons near the LCD screen shall be used to
access menu items and front panel lockout.
LCD Screen: Backlit liquid crystal display shows speaker presets and signal
processing.
Signal Indicator: Green LED, one per channel, illuminates when a very low-level
signal is present at input.
?10 Indicator: Green LED fl ashes when output signal exceeds ?10 dB below
clip.
?20 Indicator: Green LED fl ashes when output signal level exceeds ?20 dB
below clip.
Ready Indicator: Green LED, one per channel, illuminates when the amplifi er is
ready to produce audio.
Clip Indicator: Red LED, one per channel, turns on at the threshold of audible
distortion.
Temp Indicator: Red LED, one per channel, illuminates under excessive temperature
conditions.
Power Indicator: Blue LED illuminates when the amplifi er has been turned on
and has power.
Rear panel controls and connectors shall include the following:
AC Line Connector: NEMA 5-15P (15A).
Input Connector: Two 3-pin removable Phoenix-type connectors each accept a
balanced line-level input signal.
Output Connectors: 4-position barrier strip with connectors for dual louspeakers
or bridge-mono loudspeaker.
HiQnet USB Connector: Type B, connects to a HiQnet network.
HD-15 Connector: For cinema I/O compatibility with DSi-8M System Monitor.
The amplifi er shall have the following specifi cations:
Output Power: 2 ohm Stereo (per channel): 1,600W with 1% THD, 4 ohm
Stereo (per channel): 1,200W with 0.5% THD, 8 ohm Stereo (per channel):
650W with 0.5% THD, 4 ohm Bridge-Mono: 3,200W with 1% THD, 8 ohm
Bridge-Mono: 2,400W with 0.5% THD.
Voltage Gain at 1kHz, 8 ohm rated output: 26 dB.
Frequency Response: +0/?1 dB from 20 Hz to 20 kHz at 1 watt into 4 ohms.
Load Impedance: Safe with all types of loads. Rated for 2 to 8 ohms in Stereo
mode, 4 to 16 ohms in Bridge-Mono mode.
Sensitivity at 8 ohm rated output: 3.61V.
Sensitivity at 4 ohm rated output: 3.47V.
Sensitivity at 2 ohm rated output: 2.84V.
Signal to Noise Ratio (below rated 8-ohm power at 1 kHz): 105 dB
(A weighted).
Damping Factor: Better than 500 from 20 Hz to 500 Hz.
Crosstalk: > 70 dB below rated power, 20 Hz to 1 kHz.
Input Stage: Input is electronically balanced and employs precision 1% resistors.
Input Impedance (nominal): 20 k ohms, balanced;10 k ohms, unbalanced.
Maximum Input Signal: +22 dBu typical.
AC Line Voltage and Frequency Confi gurations Available: 100V, 120V, 220-240V,
50/60 Hz.
AC Line Current: 8.0A.
At Idle: Draws no more than 90 watts.
Operating Temperature: 0° C to 40° C at 95% relative humidity (non-condensing).
The DSP section shall have the following specifi cations:
Input EQ: 6 parametric fi lters per channel with adjustable Q, ±15 dB boost/cut.
Also adjustable high and low shelving fi lters. This 8-fi lter EQ section can be
bypassed.
Crossover Filters: Highpass and lowpass per channel. Butterworth 6/12/18/24
dB per octave, Linkwitz-Riley 24/48 dB per octave. Also includes ±15 dB bandpass
gain and polarity control.
Output EQ: 8 parametric fi lters per channel with adjustable Q, ±15 dB boost/cut.
This 8-fi lter EQ section can NOT be bypassed. Filters are enabled individually.
Output Limiter: Prevents clipping and protects loudspeakers. Choice of ?3, ?6,
or ?12 dB threshold per channel.
Delay: Up to 50 msec total delay per channel.
Presets: 20 presets. One is ?DSP OFF.? Fifteen are factory-set for JBL Cinema
systems. Four are user-defi nable.
Protection shall include the following:
DSi-Series amplifi ers shall be protected against shorted, open or mismatched
loads; overloaded power supplies; excessive temperature; chain destruction
phenomena; excessive output current, and input overload damage. They also
protect loudspeakers from input/output DC, large or dangerous DC offsets and
turn-on/turn-off transients
The chassis shall be steel. Cooling shall be by a proportional speed fan with
front-to-rear airflow.
Dimensions shall be EIA Standard 19-in. rack mount width (EIA RS-310-B), 3.5
in. (8.9 cm) high and 12.25 in. (31.11 cm) deep behind mounting surface.
Net weight shall be 19 lb (8.6 kg). Shipping weight shall be 22 lb (10.0 kg)
The amplifier shall be designated the Crown DSi 4000.
|
Number of Channels: 2
Output Power: (per channel)
8 ohms 575W
4 ohms 1025W
2 ohms 1750w
Output Power: (bridged)
8 ohms 2050W
4 ohms 3500w
THD%: (@1dB below max output)
@ 1kHz | Crown XTi 4002 Features at a Glance:
* Stereo Wattage: 1600W @ 2 ohms, 1200W @ 4 ohms, 650W @ 8 ohms
* Bridged Mono Wattage: 2400W @ 8 ohms, 3200W @ 4 ohms
* Peak Plus Limiters provide the ultimate in system performance and protection by allowing full control over threshold, attack, and release
* Enhanced Subharmonic Synth section provides user control over frequency, gain and filter type for system-specific tuning
* 3 User-defined fan mode controls - normal, early and fullspeed - for matching fan performance to a specific application
* New system monitoring provides software visibility of AC line voltage and power supply temperature
* Integrated cast-aluminum handles for easy handling and enhanced durability
* Locking power cord clip provides a secure connection between the amplifier and power cord
* Updated HiQnet Band Manager and System Architect control software
* Increased number of presets to a total of 30; 29 of which are user definable |
The versatile PX series power amplifiers lineup combines intelligent processing with high output power to meet the requirements of a vast range of sound reinforcement environments. 2x800W@8Ω / 2x1050W@4Ω
The versatile PX series power amplifiers lineup combines intelligent processing with high output power to meet the requirements of a vast range of sound reinforcement environments.
- 2x800W@8Ω
- 2x1050W@4Ω
- Newly developed Class-D amplifier engine with a custom LSI
- Flexible onboard PEQ, crossover, filters, delay, and limiter functions
- Yamaha Speaker presets
- Utlities for safe and secure operation
Type: | Power Amplifier | Power: | 1050W x 2 / 4Ω, 2 x 800W x 8Ω | Frequency Response: | - | Inputs: | XLR-3-31 x2, 1/4 "PHONE(TRS) x2 | Οutput: | Neutrik speakON NL4 x2, Binding post x2 pairs, 1/4" PHONE(TS) x2 | THD: | 0.1% (1kHz, 10W), 0.3% (1kHz, Half power) | Special Items: | - | Dimensions (W x H x D): | 48 x 8.8 x 38.8 cm | Rack Mount: | Yes | Weight: | 7,2 kg | Τype: | Low Impedance | Power 4Ω: | 1000W-1500W | Rack Mount: | 2U |
|
The new flagship of the LX series delivers a mighty 2 x 2100 watts into 2 ohms and 2 x 1500 watts into 4 ohms and therefore has plenty of headroom for large subwoofer arrays. For decades, DYNACORD has been one of the leading manufacturers in the pro audio sector and has established a secure position in the amplifier market thanks to the excellent audio performance,absolute reliability and high stability of the Linear Precision series. With their outstanding operational security, which guarantees years of problem-free use, the amplifiers of the Linear Precision series are now the standard for a wide variety of full-range and multi-way loudspeakers systems in professional venues as diverse as theatres, stadiums, discotheques, clubs and concert halls. Datasheets / ManualsManual (2.2MB)
Load Impedance 2 O, 4 O, 8 O Max. Midband Output Power, THD = 1%, 1kHz 2 O - 2100 W, 4 O - 1500 W, 8 O - 900 W Rated Output Power, THD 300 Slew Rate 38 V/µs Signal to Noise Ratio, A-weighted 108 dB Output Stage Topology Class H Power Requirements 100V, 120V, 220V, 230V, 240 V; 50Hz … 60Hz (factory configured) Power Consumption, 1/8 max. output power @ 4 ohms 1070 W Protection Audio Limiters, High Temperature, DC, HF, Back-EMF, Peak current Limiters Inrush Current Limiters, Turn-On delay Cooling Front-to rear, 3-stage fans Ambient Temperature Limits +5° … +40° ( 40°F … 105°F ) Safety Class I Dimensions ( W x H x D ) mm 483 x 88.1 x 384 Weight 8.70 kg (19.2 lbs) Optional Accessories Rear Rackmount 15.5" D112 930 (RMS15-CL), Rear Rackmount 18.0" D112 933 (RMS18-CL), LPN + Lo-Cut Filter D112963 (NRS 90268)
|
Reviews
There are no reviews yet.