| Content |
The P2110-T is a weatherproof full range, wide-dispersion, coaxial two way loudspeaker system for small and medium size distributed systems.
The high frequency section is a constant directivity horn loaded to a 1” RCF Precision Neodymium compression driver with a 1.50” diaphragm assembly for smooth, wide dispersion. The low-frequency transducer is a 10” woofer with a 2.5” voice coil. The cabinet is equipped with 12 x M 8 brass inserts, a stainless steel U-Bracket and pair of spacers for 90° mounting.
The system features a selectable line transformer for 70 - 100 Volt applications/installations, it meets the requirements of IP 55 code (International Protection Rating)
| Features |
|---|
| Cabinet is a single piece rotational moulded in medium density polyethylene, fully UV protected and waterproof IP 55 | | Front grille in custom perforated aluminium with open-cell fibres and water repellent woven fabric backing | | Stainless steel bracket | | One 10" high-output LF transducer with 2" voice coil | | One RCF Precision Neodymium 1" Compression Driver with 1.5" voice coil | | 90° x 40° constant directivity horn | | Built in passive crossover and selectable line transformer | | 10° X 20° enclosure sides for array configurations | | Active Mosfet Compression Driver Protection | | LICC (Low Impedance Compensated Crossover) network | |
12 brass suspension points (M8)
| Acoustical Specifications |
|---|
| Frequency Response -10 dB: | 95 Hz | ÷ 20 kHz | | Frequency Response -3 dB: | 120 Hz | ÷ 20 kHz | | Max SPL @ 1m: | 118 dB | | | Horizontal coverage angle: | 90° | | | Vertical coverage angle: | 40° | | | Directivity index; Q: | 11 | | | System Sensitivity: | 95 dB | | | Nominal Impedance: | 16 Ω | | | Power Handling: | 200 Watt | | | Peak Power Handling: | 800 Watt | | | Recommended Amplifier: | 400 | | | Protections: | Dinamyc | | | Crossover frequencies: | 2000 Hz | |
| TRANSDUCERS |
|---|
| Compression Driver: | 1.5" HF driver, 1" voice coil | | | Nominal Impedence: | 8 Ω | | | Input Power Rating: | 25 Watt AES | | | Sensitivity: | 106 dB | | | Woofer: | 10" woofer, 2.5" voice coil | | | Nominal Impedence: | 16 Ω | | | Input Power Rating: | 180 Watts AES | | | Sensitivity: | 95 dB | |
| INPUT SECTION |
|---|
| Input connector: | 5m, 4-adriges Neopren Kabel | | | Constant voltage transformer: | 70/100 | | | Power Selection: | 70V/30W ,15W , 100V/60W, 30W | |
| CABINET |
|---|
| Cabinet Material: | Polyethylene rotomoulded | | | Hardware: | 12 x M8 inserts+ U-brackets and pair of spacers | | | Grille: | Custom perforated aluminium grille with open-cell fiber and water repellent woven fabric backing | | | Colour: | Grey | |
| PHYSICAL SPECIFICATIONS |
|---|
| Height: | 350 / 13.78 mm/inch | | | Width: | 350 / 13.78 mm/inch | | | Depth: | 320 / 12.60 mm/inch | | | Net Weight: | 13.5 / 29.75 Kg/Lbs |
|
|
10" Passive Loudspeaker
- 1200 W (Peak), 127 dB peak SPL system that is reliability verified with over 500 hours of abuse testing and endurance testing to 4x typical industry practices.
- 1.4 inch DH-1C (1 inch exit) titanium compression driver for extended transparent high-frequency response.
- High-output EVS-10M woofer designed to exacting specifications for superior durability and exceptional low-frequency reproduction.
- EV-patented Signal Synchronized Transducers (SST) waveguide design provides precise and consistent coverage, minimal distortion, and maximized acoustical loading.
- Professional-grade hardware: three M10 threaded mounting points for forged eyebolts, integrated pole-mounts and the proven ZLX two-handle design for easy lifting.
The ELX series is designed to deliver an unprecedented combination of sound quality, portability and durability at its price point. All-new custom components—tested to levels far exceeding the industry norm—make ELX200 a robust workhorse capable of handling real-world abuse and professional applications beyond the capability of competitors’ products in its category.
Every aspect of ELX200 is designed for ideal results as part of the whole - the acoustical, electrical and mechanical components all work together seamlessly. The full-range models feature a low profile form factor designed with a high-spec composite enclosure to balance weight, manageability, as well as structural integrity. The proprietary features that have made the other members of the EV portable speaker family a goto for best-in-class performance are also present: Signal Synchronized Transducers (SST) waveguide concept.
EV\'s industry-leading quality and testing procedures yield efficient transducer design and meaningful specs, resulting in components that deliver accurate, linear response at the system’s highest output levels. Translation: loud and clear all the way up to the limit. Unified in one of the strongest full-range composite enclosures ever built by EV. The ELX200 is established as the new benchmark for toughness - both acoustically and physically; maximum efficiency with maximum toughness. |
| 2-Way, 10“
High Power System |
| Characteristics |
|
Multi-angled unit, designed for Sound reinforcement or floor monitoring. |
|
Multi-use Mid-High Constant Directivity, rotateable 90x45 degrees Horn. |
|
Active driver "Power Guard" protection without any effective loss. |
|
High Sound Pressure Level, (128dB Peak@1m, pink noise with a 6dB crest-factor). |
|
Rotating Horn and optimised cabinet architecture for monitoring and small P.A. uses. |
|
Two-way passive 8 Ohm design to be used with a single power Amp channel per cabinet to obtain an easy assembly and low cost. |
|
Passive filter, which optimises the voice critical zone response. |
|
Double input NL-4 Neutrik connector permitting parallel bridging. |
|
Steel front grille with acoustic foam, easily removable, held in place with powerful Neodymium magnets. |
|
Suspension Tracks on top bottom, standard pole cup and inserted threads. |
|
The specific electronic controller guarantees: linear performance, Powerful bass response, and reliability. |
| Applications |
|
Touring, installed P.A., theatres, multi-purpose rooms, etc. |
|
High performance Monitoring |
|
When used together with the series' Sub-woofer PMS-15, the system becomes a performing set-up for many dance applications. |
| Specifications and Characteristics |
| Frequency Response (Hz)1 |
±3dB 60Hz - 18KHz |
| Frequency Range (Hz)1 |
-103dB 40Hz - 20KHz |
| Nominal Impedance |
8 Ohm |
| Power Rating |
|
| (RMS)2 |
300W |
| Program2 |
600W |
| Peak2 |
1200W |
| Horizontal Coverage |
(-6dB) 90? |
| Vertical Coverage |
(-6dB) 40? |
| Sensitivity (dB/1w@1m) |
97dB SPL |
| SPL Max. Peak (dB SPL@1m)3 |
128dB SPL |
| Connectors |
2 Neutrik NL-4 Connectors on steel plate |
| Recommended Signal Processor |
RAM Audio LMS-244 Digital Processor |
| Recommended Power Amp |
250W / 500W @ 8 Ohm, 1 PM-10 / channel |
| Recommended Sub-woofer |
Space PMS-15 |
| Enclosure and Installation |
| Enclosure |
Vertical, multi-angle 15mm Baltic cross-ply construction, tongue and groove assembly throughout.
Bi-component epoxy finish. |
| Protection Grille |
1.5mm laminated steel with textured epoxy finish. |
| Handle |
On top of the cabinet. |
| Dimensions (H,W,D) mm |
521 x 324 x 294 mm 20.5x12.7x11.6 inches |
| Net Weight |
18Kg (39.6 pounds) |
| Rigging |
Integrated Track Rigging System on top and bottom. M-6 Inserts for bolt assembly. |
|
| Notes |
|
| 1 Specifications in half space
2 With filtered Pink Noise 6dB crest-factor
3 Calculated from the Sensitivity and Power Data |
|
- 38 Hz to 17 kHz frequency range
(-10 dB) - 250W pink noise, 500 watts continuous program power capacity
- 120 x 110 degree coverage horn
- 150W, 75W, 38W at 70V/100V (plus 19W tap at 70V only)
- 4 Ohm Bypass
- Outdoor-rated screw down input terminal strip (with MTC-PC2 sealed entrance cover)
- Available in black or white (Control 30-WH)
- Dimensions (HxWxD): 593 mm x 372 mm x 345 mm (23.3 in x 14.6 in x 13.5 in)
- Net Weight: 18.9 kg (42 lb)
|
M1001 is a multipurpose two-way full-range speaker system, suitable in a wide range of installations.
The compactness, together with the elegant and neutral design with accurate finishing make M1001 suitable for almost any environment and architectural constraint.
Available mounting accessories allow you to use the M1001 wall or ceiling mounted, with reference to the several possible applications.
The M1001 has a controlled dispersion and delivers undistorted SPL value above any expectation from such a compact speaker system.
The M1001 features high sensitivity thanks to the use of oversized magnets and a comfortable sound quality with smooth and wide frequency response performed thanks to the Kapton diaphragm compression driver loaded on a constant directivity horn.
The LICC crossover design includes an electronic protection on high frequency device.
General Specs
High Quality 2-way passive loudspeaker
1 x 10" woofer, vented
1 x 1" driver, on 90°x60° CD horn
High Power Handling ‘Low Impedance Compensated Crossover\', with electronic protection for the driver
300W AES power handling
Steel Front Grille with robust double mesh polyester clothing
Rotatable RCF front logo
Installation points are available on the rear panel, top and bottom
All models have a 4-pin EUROBLOCK connector (audio input and parallel link output)
Acoustical Specs
Frequency Response -10 dB:60 Hz ÷ 20000 Hz
Max SPL @ 1m:128 dB
Horizontal coverage angle:90°
Vertical coverage angle:60°
Directivity index; Q:10
System Sensitivity:97 dB
Nominal Impedance:8 Ω
Power Handling:300 W
Peak Power Handling:1200 W
Recommended Amplifier:600 W
Protections:Dynamic
Crossover frequencies:1700 Hz
Inputs/Outputs
Input connector:4-pin EUROBLOCK
Height:500 / 19.68 mm/inch
Width:265/ 10.43 mm/inch
Depth:320 / 12.60 mm/inch
Net Weight:13.2 / 29.08 kg/lbs |
Made for permanent sound placement.
The Mackie iP-10 10″ Installation Loudspeaker is designed exclusively for a wide range of installed sound reinforcement applications. Behind iP-10's clean, professional look are a high-output, custom-designed 10″ woofer and premium 1.4″ titanium diaphragm compression driver delivering rich, articulate full-bandwidth response. Ample rigging points support vertical and horizontal rigging and a choice of Neutrik or terminal connections provides install flexibility. Optional ceiling and wall mounts are available for aesthetically demanding venues. Plus, the companion iP-18S 18″ subwoofer is perfect for additional low-frequency response and output in larger applications.
FEATURES
10″ 2-way low-profile installation loudspeaker
10″ high-output ceramic woofer with 2″ voice coil for maximum output
1.4″ titanium compression driver provides smooth, consistent high-frequency response
8 x M10 rigging points and rotatable 90° x 50° horn for vertical/horizontal rigging
Rotatable center logo allows for clean presentation in all configurations
Convenient terminal strip connectivity saves time and cost
Dual Neutrik parallel connectors
Lightweight, compact and durable 15mm poplar cabinet construction
SPECIFICATIONS
iP-10 10" 2-Way Passive Loudspeaker
Frequency range (-10 dB): 50 Hz - 20 kHz
Coverage pattern: 90° x 50°
Power handling: 200 watts continuous / 400 watts program
Max SPL: 124 dB
Crossover frequency: 3 kHz
Nominal impedance: 8Ω
Height: 20.5 in / 520 mm
Width (Front): 12 in / 310 mm
Width (Rear): 6.8 in / 172 mm
Depth: 13.4 in / 340 mm
Product weight: 26 lb. / 11.8 kg |
Reviews
There are no reviews yet.