Content |
The e 608 is a super-cardioid microphone ideal for almost invisible clip-miking
of woodwind (except certain Flutes), brass and drums. A newly developed clamp
and gooseneck mounting enables the capsule to be positioned close to the signal
source for high realism and high-level output.
Features
Rugged reinforced glass-fibre body
Shock-mounted capsule provides low sensitivity to impact and handling noise
Hum compensating coil
Extremely robust connection cable with XLR connector
Delivery Includes
1 e 608
1 microphone clip
1 pouch
Technical Data
Frequency Response 40.....16000 Hz
Sensitivity in free field, no load (1kHz) 0,8 mV/Pa
Min. terminating impedance 1000 Ohm
Dimensions d 17 x 185 mm
Weight w/o cable 20 g
|
Type Condenser - Omni
Frequency Ressponse 60Hz - 18kHz
Sensitivity -33.5dB re 1 Volt/Pascal (21.00mV @ 94 dB SPL) +/- 2 dB @ 1kHz
Resistance 3000Ω
Dimensions 4.50mmW x 12.00mmH x 4.50mmD
Weight 1.00gm
Accessories Αntitrauma case,WS-LAV, Minifur LAV, Micon cable, Spanner |
Shure SLX14 Instrument Wireless System Features:
SLX4 Wireless Receiver:
Automatic Frequency Selection
Automatic Transmitter Setup
960 Selectable frequencies across 24MHz bandwidth
Detachable 1/4 wave antennas
Microprocessor-controlled diversity
RF presence LED
5-segment audio meter
Multi-function, backlit LCD
Low battery indicator
Frequency and power lockout
Rugged metal chassis
Volume control on rear of unit
1/2 rack design
Furnished rack hardware
Non-slip bumpers for use out of rack
XLR and 1/4" outputs
SLX1 Bodypack Transmitter
Automatic Transmitter Setup
Backlit LCD with timeout feature
Frequency and power lockout
3-segment battery fuel gauge
2 AA batteries (included) provide 8 hours of continuous use
518 - 782 MHz operating range
Shure SLX14 Instrument Wireless System Specifications:
SLX4 Wireless Receiver:
Audio Output Level (ref. ± 38kHz deviation with 1kHz tone): XLR connector (into 600 Ohm load): —13dBV; 1/4" connector (into 3000 Ohm load): —2dBV
Output Impedance: XLR connector: 200 Ohms; 1/4" connector: 1kohms
XLR output: Impedance balanced; Pin 1: Ground; Pin 2: (+); Pin 3: (-)
Sensitivity: —105 dBm for 12 dB SINAD, typical
Image Rejection: >70 dB, typical
Power Requirements: 12—18 Vdc at 150 mA, supplied by external power supply
Operating Range Under Typical Conditions: 300 ft. (100m)
Note: Actual range depends on RF signal absorption, reflection, and interference
Audio Frequency Response (+/— 2 dB): Minimum: 45 Hz: Maximum: 15 kHz
Note: Overall system frequency depends on microphone element.
Total Harmonic Distortion (ref. +/— 38 kHz deviation, 1 kHz tone): 0.5%, typical
Dynamic Range: >100 dB A-weighted
Operating Temperature Range: —18 degree C (0 degree F) to +50 degree C (+122 degree F)
Note: battery characteristics may limit this range
Dimensions (H x W x D): 1.65 x 7.76 x 5.28 in., (42 x 197 x 134 mm)
Weight: 1 lb. 13 oz. (816 g )
Housing: Galvanized steel
Transmitter Audio Polarity: Positive pressure on microphone diaphragm (or positive voltage applied to tip of WA302 phone plug) produces positive voltage on pin 2 (with
respect to pin 3 of low impedance output) and the tip of the high impedance 1/4-inch output.
Logic Connections: Pin 1: Logic output, Transmitter Mute Status. Mute=low (0 V). Sinks up to 100 mA. Absolute maximum -0.7 to 5.5V DC; Pin 2: Logic ground; Pin 3: Logic output, Battery Status. Good=low (0 V). Sinks up to 100 mA; Absolute maximum -0.7 to 5.5V DC
SLX1 Bodypack Transmitter
Audio Input Level: -10 dBV maximum at mic gain position, +10 dBV maximum at 0 dB gain position, +20 dBV maximum at -10 dB gain position
Gain Adjustment Range: 30dB
Input Impedance: 1 Mohms
RF Transmitter Output: 30 mW maximum (dependent on applicable country regulations
Dimensions (H x W x D): 4.25 x 2.50 x 0.75 in. (108 x 64 x 19 mmD)
Weight: 81 grams (3 oz.) without batteries
Housing: Molded ABS case
Power Requirements: 2 "AA" size alkaline or rechargeable batteries
Battery Life: >8 hours (alkaline)
|
The Electro-Voice ULM18 Unidirectional Lavalier Microphone provides hands-free speech and vocal operation with the Electro-Voice R300 wireless microphone system. The ULM18 connects to the BP300 beltpack transmitter.
Product Highlights - For R300 Wireless System
- Compatible with BP300 Beltpack
- Unidirectional Polar Pattern
|
Transducer Electret condenser
Polar Pattern Cardioid
Frequency Response 20 to 20,000Hz
Output Impedance 165.5 Ω
Sensitivity -39.0 dBV/Pa (11.0 mV)
Max Input Sound Level (SPL) 1000 Ω load: 129.5 dB SPL; 2500 Ω load: 134.5 dB SPL
Signal-to-Noise Ratio 57.0 dB
Dynamic Range @1kHz
1000 Ω: 92.5 dB SPL; 2500 Ω: 97.5 dB SPL
Self Noise 37.0 dB
(equivalent SPL, A-weighted, typical)
Clipping Level 1000 Ω load: 1.0 dBv; 2500 Ω load: -4.5 dBv
Operating Temperature Operating: 0 to 135°F (-18 to 57°C)
Storage: -20 to 165°F (-29 to 74°C)
Polarity XLR: Positive pressure on diaphragm produces positive voltage on pin 2 with respect to pin 3
Power Requirements 11-52VDC phantom power (IEC-61938),
Dimensions (LxDiameter) Length: 5' (1.52m)
Diameter: 0.23" (5.8mm)
Weight 4.3 oz (121 g)
|
Shure cable with base WL180N fits with R183/184/185 |
Reviews
There are no reviews yet.