| Content |
The VX-200SZ is an audio signal output module of the VX-2000 system with speaker line impedance detection. This module is to be mounted in the VX-2000SF Surveillance Frame and detects speaker line short circuits, open circuits by comparing impedance readings, and ground fault.
| Power Source | Supplied from VX-2000SF | | Current Consumption | Under 150 mA | | Power Amplifier Link | RJ45 female connector for connecting the VP-2064, VP-2122, VP-2241,
VP-2421 Power Amplifier.
Twisted-pair straight cable (TIA/EIA-568A standard) | | External Attenuator Control Output | Plug-in screw connector, relay, no-voltage make contact output,
transfer type, withstand voltage: 30 V DC, 250 V AC,
contact current: Under 7 A (DC), under 7 A (AC)
Applicable cable diameter: AWG 24 - AWG 16 | | Speaker Output | Plug-in screw connector
Applicable cable diameter: AWG 24 - AWG 16 | | Power Amplifier Input | Plug-in screw connector for connecting the VP-2064, VP-2122, VP-2241,
VP-2421 Power Amplifier.
Applicable cable diameter: AWG 24 - AWG 16 | | Fault Detection System | Short circuit, open circuit (impedance detection method), ground fault | | Finish | Panel: Surface-treated steel plate | | Dimensions | 30.5 (W) × 132.6 (H) × 290.3 (D) mm | | Weight | 320 g | | Accessory | Plug-in screw terminal……1 | | Option | Equaliser card: VX-200SE | | Applicable Model | VX-2000SF |
|
- PRIORITY CONTROL It controls the priority of emergency, timer, remote1, remote2, main(normal). - AUTO FIRE SENSOR The fire alarm will be given automatically to the designated areas by detecting fire sensor input. - SPEAKER SWITCHING ON EMERGENCY OR NORMAL(MAIN) You can control the speaker relay on emergency or normal(main) mode by using the speaker switch on front panel. - DISPLAY STATUS You can easily check the priority status. - 2 AND 3 WIRE SPEAKER LINE SYSTEM You can control the speaker line on the 2 wire system or 3 wire system. - EXTENSION FUNCTION You can easily expand by connecting additional ECS-616. ![]()
| ECS-616 | | Priority Control | Emergency >Timer > Remote1 > Remote2 > Main | | Link in/ out Interface | RS-422(19200bps,Data 8bits,Stop 1bit, Non Parity bit, Start1bit) | | Link in/ out interface Distance | 1.2 km | | Operation Temperature | -10 °C ~+ 40 °C | | Power Source | 24V DC | | Power Consumption | 900mA | | Weight | 4.8Kg/10.6Ib | | Dimensions( W x H x D) | 482(W)x 88(H) x 380(D) mm / 19(W)x 3.5(H)x 15(D)in | | ※ Specifications and design subject to change without notice. |
|
The AT series high quality attenuators features 5 attenuation settings ,,OFF'' -18dB,-12db,-6dB,-0dB. An input range from 0.5W to 60W (model dependent), and push-in connectors. Push-in connector allows quick terminal cable connection. Stylishly finished, the AT Series will suit any décor. |
| | - IT CAN CHECK SPEAKER WIRE OPEN, SHORT, AND EXCEED VALUE ACCORDING TO SETTING UP IMPEDANCE. - IT AUTOMATICALLY CHECKS SPEAKER WIRES BY PROGRAM TIMER OPERATIONS. THE POSSIBLE SET UP TIMES ARE BETWEEN 20 MINUTES AND 200 MINUTES. - RS-232C TERMINAL IN/OUT CONTROL WITH AMX/CRESTRON INTERFACE. - DC 24V OPERATION. - COMPACT DESIGN 2RU(3.5”). - KEEPS STORED VALUES BY NON VOLATILE MEMORY - ALERT SOUNDS WHEN FAULT IS FOUND - BUZZER ON/OFF FUNCTION. | | | | | | SC - 624 | | Power source | 24VDC | | Power Consumption | 300mA | | Weight | 5.2Kg / 11.5lb | | Dimensions (WxHxD) | 1482 x 88 x380mm /19 x 3.5 x 15in | | | |
| RM-200M - Five/ten zone console for VM-2120/2240 amplfiers
The RM-200M Remote Microphone that allows announcements to be made to any speaker zone and emergency announcements to all zones on a system with the VM-2120/2240 system management amplifiers.
These announcements can be made live or pre-recorded announcements
can be activated. The remote microphone is connected by cable to the
RM-210 Remote Microphone Extension unit.
SPECIFICATIONS:
| Power Requirement |
24 V DC (12-30 V DC), (Supplied from VM-2120/VM-2240 Amplifier or local power suppy.) |
| Distortion |
Less than 1% |
| Frequency Response |
100 - 10,000 Hz |
| Distortion |
Less than 1% |
| Signal-to-Noise Ratio |
More than 60 dB |
| Audio Output |
0 dB*1, 600 O, balanced |
| Microphone |
Unidirectional electret condenser microphone, gooseneck type. |
| Speaker Zone Control |
Zones 1-5 (Zones 1-10 with 2 stacked amplifiers) Groups 1-2, and All-Zone Broadcast |
| Emergency Broadcast |
Activation of Emergency Broadcast (pre-recorded announcement*2 or live microphone announcement) by Emergency Switch |
| Voice Announcement Board Control |
Activation of 5 messages*2 |
| Number of Connectable Units |
Up to 4 |
| Communication System |
RS-485 |
| Volume Control |
Microphone volume control |
| Connection Cable and Connector Category |
5 STP cable, RJ45 connector |
| Communication Distance |
800 m maximum in total |
| Finish |
ABS resin |
| Dimensions |
190 (W) × 75.7 (H) × 21.5 (D) mm (Gooseneck microphone excluded) |
|
*1 0 dB = 1 V
*2 An optional EV-200 Board must be mounted in the VM-2120 or VM-2240 Amplifier. |
|
The PT-9107SD from Inter-M Americas is a high-quality, single rack space digital AM/FM tuner ideal for use in restaurants, retail, offices, and more. It offers both mono and stereo outputs for compatibility with a variety of sound systems. A front-panel display shows information for channel, band, memory, and tuning. Up to twenty stations may be pre-set so your favorites are never more than a click away.
The tuner has a Digi-Link function for remote control. AC and DC power inputs are provided so that emergency 24VDC power may be connected if needed. The PT-9107SD is a great choice for applications needing a high-quality, easy-to-use rack-mountable tuner.
• Single rack space AM/FM tuner • Stereo and mono outputs • Fixed and variable outputs • Front-panel display screen • Stores up to 20 presets • Digi-Link function for remote control • Auto scan SPECIFICATIONS:
Tuning RangeFM: 87.5 - 108MHz
AM: 522 - 1611kHz SensibilityFM: Less than 3uV
AM: Less than 100uV Signal to Noise RatioFM: Greater than 65dB
AM: Greater than 40dB Total Harmonic Distortion (THD)FM: 0.3%
AM: 1% Output LevelFM Mono Balanced: 1V
FM Stereo Balanced: 500mV
AM Mono Balanced: 240mV Controls1 x Power Switch
1 x Memory Button
1 x Preset Button
1 x Mode Preset/Tune Button
10 x Preset Recall Buttons
1 x Volume Control Knob
1 x Mono/Stereo Button
1 x AM Selector Button
1 x FM Selector Button
1 x Up Button
1 x Down Button
1 x Reset Button (Rear Panel) Connectors1 x AC Power In
1 x DC Power In
1 x Fixed Output Connector
1 x Mono Variable Output Connector
1 x Stereo Variable Output Connector
1 x AM Antenna Connector
1 x FM Antenna Connector
1 x Digi-Link Connector Power Source100/120/230/240VAC, 50/60HZ
24VDC Power Consumption11W Dimensions (WxHxD)19 x 1.75 x 11" (483 x 44 x 280 mm) Weight7.7 lbs (3.5 kg)
|
Reviews
There are no reviews yet.