| Content |
The amPlug Twin rolls back the years to capture the sound of the legendary clean American dual speaker combo tube amp. Noted for its sparkling and sustained clean sound, this amp has been is widely used in many genres - rock, blues, jazz, country, and more. Raising the gain provides a powerful American tube overdrive sound. A stereo chorus effect is built into the amPlug Twin, adding natural spaciousness and depth to the sound. As you play these sounds, you're sure to forget the passage of time, and lose yourself in the tones loved by musicians in styles such as jazz, country, and blues.
Specifications - Controls: Gain, Tone, Volume; STANDBY/ON/FX switch
- Terminals: PHONES Jack (stereo), AUX In Jack (stereo)
- Power supply: AAA batteries (x 2)
- Battery life: amPlug Twin (FX on):
- With zinc-carbon batteries: approximately 3 hours
- With alkaline batteries: approximately 11 hours
- Dimensions (W x D x H): 86 x 80 x 31mm/3.39" x 3.15" x 1.22“
- Weight: 40 g/1.41 oz. (not including batteries)
- Included items: AAA batteries (X2) (for verifying operation)
|
The PHDA02 - a reference class headphone amplifier with Stereo, Mono, and Dual Mono operation modes.
In Stereo mode, the L/R input signal is fed to the left and right earphones while the volume level is set by the Stereo/Left control. The front panel inputs provide simultaneous connection of two headphones in parallel. In Mono mode, the left and right channels are summed, and the resulting mono signal is fed to both the left and right earphones. Again, volume is governed by the Stereo/Left control. In Dual Mono mode, the left and right channels can be used independently with individual level controls for the left and right earphones.
The PHDA02 operates with all headphones with an impedance of 8 up to 200 Ohms. Impedance matching is achieved by a specially designed switchable transformer. Uncommon and costly, this solution provides superior performance, dynamic range, and signal-to-noise ratio at all loads.
Combo input sockets allow for balanced XLR and unbalanced TS headphone connection while parallel XLR outputs facilitate daisy chaining multiple units. The integrated power supply operates with mains from 100 VAC to 240 VAC.
The PHDA02 is equipped with low-noise op amps, and the output amplifiers' discrete power transistors are mounted on heatsinks. Dimensions are 1 U 9.5“.
| Palmer Monicon, and the volume is right!
With Palmer Monicon, your monitor volume is always under control. The passive mini-mixer with the oversized control is inserted between the stereo output of the notebook, PC or interface and an active monitor system and thus permits convenient and precise volume control of the monitors from the workstation. The passive circuitry with only a few components has absolutely no affect on the sound. Mute and mono buttons make it possible to mute the outputs and merge the stereo output signal into a mono master signal.
The inputs and outputs of the controller are equipped with XLR connectors and the 3.5mm stereo TRS sockets usually found on computers. Combo input sockets also permit connection with 6.3 mm TRS plugs. Thus the Palmer Monicon is compatible with both professional and consumer equipment. Genuine wood sides make the practical studio tool in its massive powder-coated sheet steel housing an elegant looking "little helper" that is a typical Palmer product.
- Type: passive
- Number of channels: 2
- Number of inputs: 2
- Input connections: XLR Combo / 3.5mm stereo jack
- Input type: balanced/unbalanced
- Maximum input level: +20 dBu
- Input impedance: 10 kohms balanced/ 5 kohms unbalanced
- Number of outputs: 2
- Output connections: XLR/m, 3.5 mm stereo jack
- Output type: balanced/unbalanced
- Max output level: +20 dBu
- Output impedance: 600 ohms
- Frequency response: 10Hz - 40 kHz +/- 1 dB
- THD: 0,001 %
- Max. attenuation: 85 dB (attenuator), 112 dB (attenuator + mute)
- Controls: Attenuation, Mute, Mono
- Housing material: sheet steel/wood
- Housing surface: powder-coated
- Width: 164 mm
- Height: 62 mm
- Depth: 85 mm
|
Specifications
General
Frequency response
20 Hz - 20 kHz (+0 dB, -1.5 dB)
Signal-to-noise ratio
100 dB (IHF A-weighted, input level control min.)
Channel separation
80 dB between adjacent channels
Line input
Front: 6.3 mm jacks, unbalanced
Rear: RCA connectors, unbalanced
Input impedance
40 kOhm
Nominal level
-10 dBV (0.3 V)
Headphone outputs
four 6.3 mm stereo jacks
Maximum output power
2 x 1.5 W at 8 Ohm (1 channel in use)
2 x 1,2 W an 8 Ohm (four channels in use)
Power supply
230 V AC, 50 Hz
Power consumption
10 W
Dimensions (W x H x D)
482 mm x 44 mm x 196 mm
Weight
4 kg | The new HP4 from PreSonus answers the need for a headphone distribution
amplifier with professional specifications in a small package at an affordable
price. The HP4 features four discrete headphone outputs on the front panel
each with its own volume potentiometer and 150mW of amplification per channel.
The HP4 also features adjustment over control room monitors with a separate
volume control, monitor mute switch and mono switch giving you an extremely
powerful monitoring solution at an amazingly low price.
Features
? Four High Power Headphone Outputs
? Ultra loud (150mW per channel)
? Ultra quiet operation
? Musical Wide Dynamic Range
? Control Room Monitor Outputs with Level Control
? Mono or Stereo Operation
? Monitor Mute Switch
? Daisy Chain an Infinite Number of Units
? Compact package
Technical Specifications
Input
TRS Impedance 10K Ohms
Panel Controls
Headphone Level 1 to 12
Monitor / Feed Output -80dB to +10dB
Mono Switch
Monitor / Feed Mute
Power Supply
Type Linear
Input 16VAC/1000mA
Output
TRS Balanced 51 Ohms Impedance
Performance
THD+Noise (Unweighted) 0.002%
Noise Floor -98dB
Signal To Noise >95dB
Power Supply Rejection >98dB
Power 16 Watts
Physical
Weight 5lbs./ 2.3 kg.
Dimensions 5.5 x 5.5 x 1.75
Mounting Max Rack and Universal Rack Tray
Chassis Steel
Panel Brushed Aluminum
Sides Cast Aluminum | Behringer HA-400 Ultra-Compact 4-Channel Stereo Headphone Amplifier
Mini to the max! You can use this super-compact stereo headphone amplifier with practically all headphones?four of them at the same time, to be exact! For example, you can let up to 4 different people in your studio listen to the main mix while the recording is being made, and each listener can determine his own volume level using the dedicated output level controls. The HA400 contains 4 high-power stereo amplifiers that maintain the highest sonic quality even at maximum volume levels. Ultra low-noise 4580 operational amplifiers are included for outstanding audio performance?these are the same op amps found in ?full-size? audio equipment?plus, a DC 12-Volt adapter is included.
If you are one of those musicians who like to deck out their equipment with lots of bells and whistles, the HA400 definitely makes a great addition to the functionality of your studio.
The Behringer HA400 offers flexible amplification for up to 4 headphones. Whether you're tracking a full band, playing to a backing track, or just listening to your mix, this compact amp gives every performer diverse volume control.
Hear everything with clarity. The HA400 promises high audio quality with zero interference, no matter what headphones you use. Behringer are relied upon by professional musicians everywhere. With the HA400 headphone amplifier, you'll become a part of 50+ years of innovation and expertise.
The Highest Quality Monitoring Possible
Great monitoring is at the heart of a tight performance. Whether you're on stage or in the studio, the HA4000 delivers ultimate control for everyone playing. Discover the highest quality audio from 4 high power, stereo amplifiers. Even at maximum volume, this tidy headphone amp provides clear sound without muddiness or unwanted noise.
Industry Leading Standard
There's a reason why Behringer are leaders in their field. With 50+ years of industry experience, they've built a legacy around exceptional build quality and innovative design. The HA4000 is no exception. Every channel preserves the original sonic qualities of your input signal. That's performance you can trust.
Features
- Ultra-compact headphone amplifier
- Ideal for stage or studio use
- Full control for every channel with 4 independent stereo high-power amplifier sections
- Extremely high audio quality with virtually all types of headphones, even at maximum volume
- 12V DC power adapter included
- Designed and engineered by Behringer in Germany
Specifications
Line Inputs
-
-
- Type: 1/4'' TS Jack, Stereo
- Impedance: 100kohms
- Max. input level: +15dBu
Headphone Outputs
-
-
- Type: 1/4'' TRS Jacks, Stereo
- Impedance: Approx. 80ohms
- Max. output level: Approx. 40mW in 100ohms
Power Supply
-
-
- Power supply: External power supply 12V
Dimensions/Weight
-
- Dimensions: 47mm (H) x 57mm (W) x 104mm (D)
- Weight: 0.32kg
|
Reviews
There are no reviews yet.