WORK WD 421 Audio Splitter 2 in & 2 out

Signal distributor. 1 stereo input / 4 stereo outputs or 1 mono input / 8 mono outputs

This audio distributor is very useful to supply several audio devices with only one audio source. Its 2 operating modes allow to work with mono or stereo signals. Output level can be controlled independently.

WD 421 adapts itself to work with different impedances, ensuring that output signal level is at least equal to input signal level. It avoids any undesired attenuation and features a LED vumeter to visualize the input signal level.

Audio signal distributor with 2 inputs and 8 outputs.
Two operating modes:
1 stereo input with 4 stereo outputs.
1 mono input with 8 mono outputs.
Adjusting Output level.
Balanced LINK output for interconnecting several units.
Individual gain control of each channel

Inputs: 2 x XLR3 female balanced.
Outputs: 8 x XLR3 male balanced.
Input sensitivity: 0 dBu.
Max. level input: 22 dBu.
Input impedance: 10 kohm.
Level range: ? to - 12dBu.
Frequency response: 20 Hz to 22 kHz.
Distortion: 110 dBu.
Noise and hum: < - 80 dB @ 20 Hz - 22 kHz.
Crosstalk: < - 80 dB @ 20 Hz - 22 kHz.
Output impedance: 120ohm.
Main supply: 110 - 120 V / 220 - 240 V 50/60 Hz.
Power consumption: 20 W.
Dimensions (WxHxD): 483 x 44 x 220 mm.
Weight: 2.75 kg.

• Connect 2 TVs or projectors and switch between 4 connected HDMI devices.
• HDMI matrix switch allows you to watch other HDMI devices on 2 screens independently.
• Use the built-in 1080p downscaler in case 1 or more screens do not support 4K resolution.
• Suitable for the latest Ultra HD 4K60 resolution (3840 x 2160/60 Hz), High Dynamic Range (HDR), Deep Color and 4:4:4 chroma colours.
• Supports Dolby Atmos and DTS:X and all other common audio formats.
• With additional digital audio output to also connect your AV receiver using a single cable.
• Supports Audio Return Channel (ARC) to avoid lip-sync problems.
• Switches automatically and/or with remote control.

• 2 channel line splitter "1 into 3"
• Each channel with: Input: female XLR type with parallel male XLR Type output 2 transformer isolated male XLR type outputs
• Transformer ratio 1 : 1
•  Nominal level: 0 dB
• Max. level +20 dB
• Nominal impedance input and output: 600 ohms
• Ground lift switch

iEQ-15 Dual 15-Band Graphic EQ with Type V? NR and AFS?

With an EQ heritage that has produced countless industry standard
patents and dates back more than 30 years, the dbx iEQ-31 easily
lives up to the dbx legacy of uncompromised sonic integrity. In
addition to unsurpassed equalization specs, the iEQ-15 also offers
the built-in necessities which include AFS? feedback Suppression,
Type V? noise reduction and PeakStopPlus? limiting. Besides
including two 15-band channels of 2/3-octave equalization, the iEQ-15
also offers +12 dB input gain range; switchable +6 or +15 dB boost/cut
range, 40mm faders, XLR, 1/4'' and Euroblock inputs and outputs,
nonconductive nylon sliders; and an intuitive user interface with comprehensive
output and gain reduction metering. As always, the inevitable result of our
meticulous attention to detail and top-quality componentry is exceptional
sound, performance, and reliability.

The iEQ series represents a major step forward in the performance of EQs.
The iEQ series is now able to offer state-of-the-art digital EQ performance
and specs with an analog look and feel. From its amazing 10Hz to 22kHz
frequency response, to its 113dB dynamic range and Advanced Feedback
Suppression (AFS?), dbx proprietary Type V? noise reduction
and PeakStopPlus? limiting, the iEQ-15 offers out of this world specifications
with a downto- earth price point. Sure to find a home in the studio, on tour and
with installed sound venues, the iEQ-15 is destined to take its rightful place in
the lineage of great dbx? signal processors that are the professional?s choice
in signal processing. With such pristine design and quality, the iEQ-15 offers
the maximum sonic flexibility in a straight forward interface and rock-solid construction.

  
? Advanced Feedback Suppression (AFS?)

? Type V? Noise Reduction

? PeakStopPlus? Limiting

? 2/3-octave Constant Q frequency bands

? Switchable boost/cut ranges of ±6 or ±15dB

? 18 dB per octave 40Hz low-cut filter

? ±12dB input gain range

? XLR, TRS and Euroblock Inputs and Outputs

? Internal Toroidal Transformer

? Frequency Response of 10Hz to 22kHz

? Dynamic range of greater than 113dB

? User Power Up Features

? Relay Bypass for Power Failure System Protection

Practical distributor with 1 input and 6 outputs

• Extends every mixer with additional outputs
• 1 stereo XLR input
• 6 stereo zone outputs (XLR)
• Each zone with level control and mono switch
• LED display of signal input and mono/stereo mode
• (19") 48.3 cm rack installation 1 U
• For application areas such as: Installation; restaurants, bars and hotels; sports centres/gyms

Package contents

• 1 x device, 1 x power cord, 1 x user manual

Features:
Eight channel / four way split per channel
Channels linkable up to 1 in, 32 out
Ultra low noise design
'SilentSwitch' Phantom Power switching
?20 dB pad switch
0 to +40 dB Gain available via rear switches
Headphone monitoring and PFL metering
Electronically Balanced Inputs and Outputs (standard)
Transformer balanced Outputs option
Intuitive, 'user friendly' layout
Flawless audio performance

EC-2
Superb Audio Quality
Active microphone and line signal splitting has a number of benefits over
using passive splitters: primarily these are improved sound quality, noise
figures comparable to the best microphone inputs, and increased resistance
to RFI.
About the MSX 32
With these benefits in mind, the ARX MSX 32 Active Microphone/Line Splitter
has been developed to deliver the performance required by the increasing
complexity of today?s standards of audio production.
The MSX 32 consists of eight channels of actively buffered ultra low noise
Microphone/Line Splitter. Each of these channels has four electronically Balanced
splits ? two outputs on the rear panel for Main and Monitor, plus two more output
splits on the front panel. All splits have the option of transformer balancing if so
specified.Each channel has a ?20 dB pad switch plus silently switchable 48V
Phantom power with indicator LED. A PFL switch and 6 LED metering enables
each channel to be easily checked with headphones for signal monitoring, and
also for line tracing when troubleshooting. Gain through the MSX 32 can be set
individually by the small DIP switches on the rear of each channel, from 0dB
through to +40 dB in 10 dB stepsA ?Link? switch links each channel to the previous
one, providing an ultimate maximum of 32 Outputs from a single input. An indicator
LED shows when this is active. A Clip LED indicates imminent signal overload
through the channel, and a numbered marker panel on the front provides a space
where individual channel connections can be noted.
Number stickers are provided to give each channel an individual number for up to
40 channels when multiple MSX32s are being used.Internally, powerful RF input
filtering removes both common mode and differential interference at ultrasonic frequencies
and above. High CMRR is achieved by the use of precision components throughout.
Advanced user options include internally jumper linking Inputs to Main outputs, and
Ground lifting Output Pins 1 as required.
Internal Power Supply
The MSX 32?s internal toroidal transformer based power supply is triple shielded to
get the maximum benefit from the ultra low noise design of the splitter circuitry.
An illuminated power switch on the front panel provides visual confirmation of AC
power connection to the unit.The headphone output and the 6 LED PFL metering
are both mounted on the right hand side of the front panel. Rear panel connectors
enable this function to be linked when using multiple MSX 32 units.
To sum up, this feature packed two RU device is the answer wherever transparent
signal buffering and routing is required.

T E C H N I C A L  S P E C I F I C A T I O N S
Signal / Noise Ratio -94dB
Distortion .008% 20Hz - 20KHz
Gain through unit Switchable 0, +10, +20, +30, +40 dB
Maximum Output +24dB
Pad Switch ?20dB attenuation
Phantom Power +48VDC slow turn on/turn off
Output Impedance 100 Ohms Electronically Balanced
(Optional Transformer balancing available)
Clip LED 1dB before clipping
Headphone Output 2 watts/8 ohms
AC Mains Input Fused IEC socket
AC Power 100-120V AC 2 amp 220-240V AC 1 amp
Transformer Type Low noise shielded toroidal
Size 2 RU - 19?W x 3½?H x 8?D, 482 x 89 x 200 mm
Weight E model - 15 lbs (7 Kg)