| Content | The Qi-amplifier range is developed for installation use to create a perfect match with the Xi installation speaker range. Due to the rugged steel housing it can also be applied for mobile use. With only 1U it gives power for 4 channels. All 4 channels are individual controllable and bridge mode can be set for each stereo pair. With the SMPS and Class-D amplification it is a light weight solution with a high efficiency power consumption / power output ratio. An advanced protection circuit will protect the amplifier and it's connected speakers. It has a short circuit/ thermal, DC ,RF protection and a soft start system. The Qi-amplifiers are made with high-quality low deviation components to ensure a perfect sound quality and a long life time.
Specifications
Output power
Stereo 4Ohm: 4x 200W
Stereo 8Ohm: 4x 120W
Bridge 8Ohm: 2x 400W
Parameters
S/N Ratio: >90dB
Input sensitivity: 0,65V
Input impedance: 20kOhm Bal./10Kohm unbal.
Technology: Class-D
Protection: short circuit, DC, RF, Soft start
Cooling: Temp controlled fan
Power supply: SMPS
Connections
Input: 4x XLR
Output: 4x Speaker connector
Power: IEC
Physical
Dimensions: 388 x 435 x 44 (WxHxD)
Installation depth: 370 (excl. conn.)
Weight: 5.8Kg
Electrical
Input Voltage: 100~240VAC...50/60Hz
Power consumption: 500W
|
Electro Voice PA 4150L features:
* 100 Watts / 8 Ohms
* 160 Watts / 4 Ohms
* The amplifier channels can be bridged for more flexibility
* Frequency response (-1dB): 10 Hz - 40 kHz
* Signal-to-Noise Ratio: 100 dB
* Provides excellent headroom for a wide dynamic range on music signals
* Protection: audio limiters, high temperature, peak current limiters, turn-on delay
* Marked level controls on the rear panel provide hidden reliable level adjustments for each channel
* Front panel LEDs indicate signal present, 0 dB, and limit
* Phoenix type connectors for inputs and outputs provide an easy rack wiring
* Cooling: front-to-rear
* Power requirements: 120V or 230V, 50 Hz - 60 Hz
* Dimensions (WxHxD): 483 x 88 x 406 mm / 19" x 3.5" x 16"
* Weight: 18 kg / 39.65 lbs
| POWER AMPLIFIER 4 X 2100 WATT / 4Ω
Very high power and channel density – • The four-channel FP
10000Q delivers a total of 10000 W (4 x 2500 W @ 2 ohms) in
only 2U
Four-channel fexibility – • Four channels in one cabinet increases
effciency, fexibility and value in powering monitor systems, line
arrays, and bi- or tri-amped systems. Adjacent channels bridgeable
for 2- or 3-channel operation
Lab.gruppen sound quality – • FP 10000Q amplifers maintain
the impeccable sonic performance standards set by the original fP
Series, with the same durability and even greater effciency
NomadLink • ® network ready – Monitoring and control of key
functions accessible via the intuitive DeviceControl software and
the robust, daisy-chained NomadLink® network
Patented Class TD amplifer topology – • Road-proven output
stage delivers Class B audio quality with Class D effciency
Regulated Switch Mode Power Supply (R.SMPS) – • Output
power remains constant even with signifcant drops in the mains
voltage
Effcient cooling system – • Unique, lightweight Intercooler® cop-
per cooling system dissipates more heat to allow extended peak
output
Adjustable parameters – • Selectable Gain, scalable Voltage Peak
Limiter (VPL), and bridge-mode operation allow custom confgura-
tion for any system or application
XLR input connectors •
Heavy-duty binding post or Speakon output connectors •
Comprehensive protection and warning – • Excessive output
current, DC, high temperature, very high frequency (VHF), short
circuit, open load, mains fuse protection, and soft start | PA Power Amplifier 4 x 160 W 4 Ohms
Multichannel Power with Minimum FootprintThe T Series multichannel power amplifiers have been designed especially for installation and networked audio systems.
T Series amplifiers* are available with 4 and 8 discrete channels and output ratings from 160 to 320 Watts per channel providing optimum solutions for multizoning. They feature Euroblock inputs, terminal strip outputs and a rugged 2U rackmountable chassis with 4 mm front panel.
*Also available as GPIO versions with remote and emergency paging switchin
Main Features
- 8 and 4-channel models with 300 and 150 Watts (RMS) output power per channel
- compact 2U rackmountable chassis, 220 mm deep, weight 6 kg only
- GPIO versions for remote and emergency paging switching
- FCM system
- oversized heat dissipation system for maximum thermal stability
- low THD and high S/N ratio
- all channels bridgeable in pairs
- switchable input gain (26, 32 and 38 dB)
- subsonic filters for each channel (35 Hz)
- intelligent, quiet fan cooling system
- terminal strip loudspeaker connectors
- PCBs with surface-mount technology (SMT) for increased reliability
- balanced inputs with superior noise rejection
- select high-quality components only
- ICL intelligent clip limiters for each channel
- recessed volume controls (optional SC-T perspex guard)
- high-efficiency two-stage Class H design
- protection, signal, clip, power on and standby LED indicators for each channel
- compact QuantaPulse power supply
- multi-voltage: automatic voltage converter for worldwide use, no switching required
- protections: soft start, turn on/turn off muting, thermal overload, DC, RF, short circuit, open circuit, load mismatch and power supply overload
ICL™: improved Intelligent Clip Limiting prevents loudspeaker damage while maintaining audio quality and punch under clipping conditions.
FCM™: the Faulty Channel Management system prevents overall amplifier shutdown.
GPIO:General-Purpose-I/O-Port
QuantaPulse™ Technology: The Soft Switching Resonant QuantaPulse Power Supply is designed to provide plenty of power when needed monitoring the necessary parameters of voltage and current for a controlled performance at all times. Bi-directional data flow between the power supply and power amp module. Two very important characteristics of the QuantaPulse power supply are the optimization against over-voltages and superior reliability.
• Eight and four channel models with 300W and 150W per channel
• Minimal footprint and mass arround 200mm depth and 6 Kg
• Optional Add-on card to interface with third party alarm systems with GPIO connections
• FCM™ Faulty Channel Management system to avoid entire device shutdown
• State-of-the-art layout for maximum performance and reliability
• Highly oversized thermal dissipation design for maximum reliability
• Superb distortion and noise figures
• All channels bridgeable by pairs
• Selectable gain in four channel groups (26, 32 and 38dB)
• Subsonic filter per channel (35Hz user selectable)
• Temperature and signal dependant, intelligent cooling system for minimal noise
• Optimal heat extraction due to the air tunneled enclosure and insulator-less power devices attachment to the heatsink
• Direct connector-less output for maximum quality loudspeaker control
• High grade engineering inside with the latest SMD technology
• Balanced Inputs with 0.1% tolerance resistors for a precise noise rejection
• Critical electronic and mechanical parts selection
• Innovative protection systems, FCM™ Faulty Channel Management and SSP™ SOA Sentry Protection
• Detented and optionally tamper-proof volume potentiometers
• Hi efficiency, two steps Class H Audio topology
• Protection, Signal and Clip indicators per channel
• Power On and Standby general indicators
• Extremely compact, fully featured QuantaPulse Power supply
• Low current consumption and heat generation allowing less demanding conditions for multiple amplifier installations
• Factory preset worldwide mains voltage power supply
• Laser cut four milimeters aluminium front panel
• Rugged 2U steel chasis
Frequency Response (power bandwidth ±0.25dB): 20Hz-20kHz
Phase Response (@1W 20Hz-20kHz): ±15deg
Total Harmonic Distortion (20Hz-20kHz):
Intermodulation Distortion (SMPTE):
Crosstalk (20Hz-20kHz): >70dB
Voltage Gain (selectable): 26/32/38 dB
Sensitivity: T604:1.5/0.8/0.4V - T1204:2.1/1.0/0.5V - T1208:1.4/0.7/0.4V - T2408:2.0/1.0/0.5V
Signal to noise ratio: T604:107dB - T1204:110dB - T1208:107dB - T2408:110dB
Required AC Mains (@8ohms 1/8 rated power): T604:1A - T1204:1.5A - T1208:1.4A - T2408:2.6A
Dimensions (WxHxD): 483x88.9x210 mm - 19x3.5x8.27 inches
Weight (Net): T604/T1204: 5.4Kg - 11.8Lbs T1208/T2408: 6.2Kg-13.5Lbs
Protections: Soft-start, Turn-on Turn-off muting, Over-heating, DC, RF, Short-circuit, Open or mismatched loads, Overloaded power supply, SSP™ and FCM™ |
Power Output Level: QD4480
8ohm (Quad Ch) 80W
4ohm (Quad Ch) 120W
8ohm bridged mono 240W
Input Sensitivity (8ohm, 1kHz) 0.775Vrms
Input Impedance 20kohm Balanced
Slew Rate (8ohm, Full Swing) ±30V/?sec
Frequency Response (±0.5dB) 20kHz ~ 50kHz
T.H.D. (f=20Hz~20kHz, Half Power) 0.03%
Signal to Noise Ratio 105dB
Damping Factor (8ohm, 1kHz) 100
Rasidual Noise -85dB
Channel Separation (8ohm, 1kHz) 80dB
Voltage Gain (4ohm) 26dB 29dB 32dB
Power Source 100-120VAC or 220-240VAC ; 50/60Hz
(supplied AC mains transformer depends on country requirements)
Power Consumption 300W 420W 770W
Weight 11.5kg/25.3lb 15.5kg/34.2lb 17kg/37.5lb
Dimensions 482(W) x 88(H) x 369(D) mm
/19(W) x 3.5(H) x 14.5(D) in
|
The XM series multi-channel power amplifiers are ideal for theater, hall, and conference room installations. The lineup includes 80W × 4 and 180W × 4 models, meeting the needs of a wide variety of installed systems. The XM amplifiers are a compact 2U size and surprisingly lightweight, making them easy to handle and install. Switching power supplies deliver high output power while minimizing the unit's physical size. The XM series has monitor/remote jacks that allow external devices to be connected for status monitoring or control from a remote location.
Dimensions (W x H x D): 480 x 88 x 412 mm, Weight: 10 kg
Four high-power channels. Switchable stereo, parallel, or bridged operation. Versatile connectivity and high-pass filters for a variety of applications. Distribution drive capability for parallel multi-speakers systems (XM4180).
Monitor/Remote connector for remote monitoring and control.
|
Reviews
There are no reviews yet.