Content |
EWI PDI-100 PARA ACOUSTIC DI Box
This is a medium grade professional application Para Acoustic Active DI, which will work well on instruments with passive pickups or active pickups.
The construction is reasonably rugged and the components are well suited for the application yielding results that are typically acceptable for all but the most discerning artists.
The on-board tone and volume controls give the operator a lot of choices in shaping their sound prior to sending the signal to the mix console. This allows an artist to use this device in-place of or in addition to a traditional stage amp for their instrument. This is an excellent choice for IEM bands, or bands that like to keep their stage volume low.
This item is typically used to split the instrument signal going to a stage amp so a feed can be sent also to the mix board, or be used as a stand-alone instrument pre-amp. It is equipped with a ¼” jack for input, a 1/4" jack for output to a stage amp, one XLR jack for the send to the board and a TRS jack for inserting an FX device.Since this is an active D.I. box, it needs to be powered which can be done either with Phantom Power from the mix board, or with the supplied internal 9v battery. The battery is fairly easy to change by removing one screw in the bottom of the case.
|
Applications
Console input extending for both Digital and Analog mixing consoles in Studio, Live and Broadcast Mic Pre-amps for ADAT/ Hard Disk/ Multitrack Recording Innovation If you love your compact Digital (or Analog) mixing console, but wish it had more microphone inputs, ARX has the solution ? the 8 Pre: eight channels of superb sounding Microphone Pre-amps in a compact 1 RU chassis. The 8 Pre is the ideal console extender for those times when you need more microphone inputs. Now you can put those unused line inputs to good use, and who knows - the 8 Pre pre-amps sound so good that you?ll probably end up using them all the time instead of the ones that came with your mixer! Superb Audio Quality The 8 Pre?s ultra low noise figures come from extensive use of premium components plus care and attention to board design and layout. The result is superb, transparent audio quality and the headroom to handle anything that a mic can throw at it. Gain is adjustable from 20 db through to 60 dB via a trim control on the front panel, plus we?ve included a ?20dB Pad switch to tame the hottest condenser mic output if required. The Clip status LED lights up 1 dB before the onset of clipping, just to warn you you?re getting close.Phantom power is switchable in banks of four channels: 1 through 4, 5 through 8. A Phase reverse switch is also provided on each pre-amp channel to eliminate any close miking problems. In short, the ARX 8 Pre is the mic Pre-amp that you?ll wish the console manufacturer had used. It provides a unique solution to today?s multiple Mic Pre-amp requirements.
T E C H N I C A L S P E C I F I C A T I O N S Input Gain 20dB to 60dB Input Pad ?20dB Input Impedance 4 KOhm Input Headroom +23dB Output Impedance 300 Ohm Output Level (Max) +23dB Frequency Response 20Hz ? 20KHz ±0.2 dB Signal to Noise ratio (Gain set @ 20 dB) ?93dB Unweighted, ?99dB ?A? weighted Distortion @ Unity Gain .004%, 20 Hz ? 10 KHz Dynamic Range 116 dB Phantom Power 48 VDC Input Connectors Balanced XLR Output Connectors Balanced TRS jack Clip Indicator Illuminates 1 dB prior to clipping Power Requirements 100/120 V AC, 220/240 V AC Weight 5 lbs/2.2 Kg Dimensions 19“W x 1?“H x 6“D, 482 x 44 x 155mm |
The PRE-73 MKIII is a one-channel vintage style microphone-, line- and instrument preamplifier. The signal path uses only discrete components like resistors, capacitors and transistors. The in- and output is transformer balanced, using two different transformers, each one optimized for its purpose. This is the way audio components were built before integrated circuits became available.
The circuit used in the PRE-73 MKIII is similar to the preamp section in the classical 1073 module with a corresponding sound character that is warm, punchy, sweet and musical. These classic characteristics have been heard on countless recordings through the years and it is a versatile sound that works very well on most sound sources and in most genres.
The essence of this sound is now available at a surprisingly low cost, making it available to nearly everyone.
Features :
-
Vintage Style electronics. No intergrated circuits in the signal path.
-
Maximum gain in MIC mode is 80 dB, enough to handle passive ribbon mics with quiet sound sources.
-
GAIN switch range 20 - 80 dB. GAIN/LINE mode switch, gain is reduced by 30 dB in LINE mode.
-
Selectable two position high frequency AIR boost eq, 3 or 6 dB @ 30 kHz.
-
Selectable 6 dB/octave two frequency high pass filter at around 40 (HP1) and 170 Hz (HP2).
-
Tantalum capacitors in the signal path.
-
Switchable impedance in MIC mode, 1200 or 300 Ohms, will change the tone of most mics. The input impedance in LINE mode is 10 kohm.
-
Switchable phantom power and absolute phase.
-
A high-impedance instrument input for any sound module, electric guitar or bass.
-
A simple but effective 4-step LED output level meter.
-
The output level control makes it possible to make fine gain adjustments and also to overload the main gain stage(s) for more character and then lower the signal to a suitable level before the output stage.
-
Combo XLR/TRS input jack and separate output XLR and TRS jacks for flexible connections.
-
Insert jack for inserting EQ´s and other units.
-
Selectable 600 ohm output termination.
-
The pcb is prepared for the Carnhill input transformer.
-
External power supply to avoid interaction with the audio circuits and transformers.
-
A solid build quality that will last many years of normal use.
The MKIII has the following new features compared to the MKII:
-
Tantalum capacitors in the signal path.
-
Selectable two position high frequency AIR boost eq, 3 or 6 dB @ 30 kHz.
-
Selectable two frequency high pass filter, 6 dB/octave at 40 or 170Hz.
-
The pcb is prepared for the Carnhill input transformer.
-
Revised and less complicated GAIN switch with a separate switch for MIC/LINE selection.
-
All GAIN settings can also be used in LINE mode .
|
-
- Ultra-high quality 8-channel A/D and D/A interface for virtually any digital recording/mixing environment
- 8 state-of-the-art MIDAS designed Mic Preamplifiers
- Phantom power on all microphone inputs
- Reference-class Cirrus Logic 24-bit converters for ultimate signal integrity
- Processes 48 and 44.1 kHz sample rates
- External sample rate synchronization via word clock or ADAT input
- Optical ADAT in/out interface for ultimate compatibility
- All mic/line inputs routed to the ADAT output
- ADAT input routed to all Line outputs
- “Planet Earth" switching power supply for maximum flexibility (100 - 240 V~), noise-free audio, superior transient response plus low power consumption for energy saving
- High-quality components and exceptionally rugged construction ensure long life
- Conceived and designed by BEHRINGER Germany
| • Road proof housing
• High quality components
• Professional balanced XLR outputs
• Level control
The ASC-202 converts consumer level stereo RCA signals to balanced XLR professional line level, and back. One side of the unit, has two XLR inputs and stereo RCA outputs. The other side has stereo RCA inputs and two XLR outputs. Each side has stereo level controls. A possible application of the SC-13 is to use it as a level control in balanced audio lines.
The DAP Pro Audio Solutions are a complete line-up of audio tools for the professional musician or audio engineer. It is a series of audio modifying tools like mini-mixers, pre-amps and converters available in active or passive models. All audio solutions are designed to meet the highest stage and audio demands and feature a metal road proof housing with rubber feet and easy accessible controls. The units also have a small footprint which make them ideal to be used and placed in any environment where space is critical.
Specifications Frequency Response: 20Hz-20KHz
Inputs: XLR/Jack Combo, RCA
Outputs: XLR male, RCA
Input sensitivity RCA in: -10 dBv
Input Impedance RCA in: 10 kOhm
Input sensitivity XLR/Jack in: +4 dBu
Input Impedance XLR/Jack in: 20 kOhm
Output voltage RCA Out: -10 dBV
Output Impedance XLR Out: 100 Ohm
Output voltage XLR Out: +4 dBu
Output Impedance XLR Out: 200 Ohm
Power supply: 18V AC (adapter included)
Dimensions: 53 x 158 x 135 mm (HxWxD)
Weight: 0,65 Kg |
Designed for high-definition field production environments, the studio-quality MP-1 is an ideal line-driver for critical radio, television, and film applications.
The MP-1 is extremely durable and easy to use. With rugged mechanical and electrical construction and high-quality components it will provide years of superb audio performance under the most punishing field conditions.
MP-1 Key Features - Superb audio specifications
- 66 dB of gain, in eleven discrete steps
- Transformer-balanced input and output
- Phantom power - 48 volt or 12 volt
- High pass filter @ 80 Hz or 160 Hz, 6 dB/octave
- Limiter makes unit virtually "unclippable“
- High current line output drive
- Excellent immunity to RF interference.
- Battery power (two x AA)
- Durable mechanical construction
|
Reviews
There are no reviews yet.