| Content |
The RØDE invisiLav is designed to aid the concealing of the Lavalier and smartLav microphones.
Its soft construction absorbs noise and vibration, while the wide, flat profile provides coverage from the elements and allows for versatile mounting. There's two mounting points in case a redundant mic is required, and cable management on the side.
Available in either a pack of three or a bulk pack of ten, the invisiLav comes with pre-cut, skinsafe adhesive that can be used to stick the invisiLav to either the body or to fabric. The invisiLav itself is also made from a medical grade skin safe material so it can be mounted on the body without fear of irritation.
|
Shure P4HW Wired Bodypack Personal Monitor
P4HW Wired Bodypack
Hardwired Bodypack
Key Features
Attached input cable
High-impact plastic chassis
Operating Controls:
Operating mode (Stereo, Mono, MixMode)
Volume knob
Balance knob
Defeatable limiter
High-frequency boost
-15 db Pad
Backlit LCD Indicators :
Battery life
Input level
Operating mode
Frequency Response
20 to 20,000 Hz
Total Harmonic Distortion
Channel Separation
35 dB (minimum)
Signal-to-noise ratio
85 dB (minimum)
Maximum Output Level
+5 dBu at 1% THD
Maximum Input Level
+7 dBu, input pad OFF
+22 dBu, input pad ON
Actual Input Impedance
> 40 kilohms
Audio Output Connector
3.5 mm stereo (left=tip, right=ring, ground=sleeve)
Power Requirements
9 V Alkaline battery
Battery Life
Up to 8 hours, volume dependant
Phantom Power Protection
Up to 60 VDC
|
12V AC-adapter for PS 4000, ASU 4000, HUB 4000, HPA 4000, CU4000 or SR 4000 | The Gravity MA 3D A lets you attach microphones, action cams and mobile phone holders to your microphone stand, and set them up flexibly. Its fastening mechanism is quick and easy to assemble. The large clamping range from 15 to 35 mm and the three joints' 360° rotation options allow you to install it as you like. Simply loosen, adjust and tighten the wing-screws.
Material: Plastic , Polyamide
Joint adjustment: Wing screw
Joint rotation: 360°
Joint tilt: 180°
Arm length: 400 mm
Suitable for mounting on: Microphone Stands
Suitable for tube diameter: 15 mm - 35 mm
Colour: Black
Thread size: 3/8”
Weight: 0,302 kg
|
Shure PM4E 6in-6out Personal Monitor Mixer
The P4M is a highly versatile four-channel, two-bus stereo mic/line mixer designed to optimize
use of personal (in-ear) monitors like the Shure PSM 400 in live performance. The P4M features
four balanced mic/line inputs, each with level and panning controls. Corresponding XLR split outputs
allow input signals to pass through the unit unaffected, while providing an independent mix.
Personal Stereo Monitors
When coupled with personal monitors, the P4M allows performers the ability to adjust personal mix
levels onstage - even during a performance - without affecting the front-of-house system. This enables
users to create and maintain consistent monitor mixes, regardless of what the venue can provide for monitors.
The P4M is available individually for use with Shure PSM 600 and PSM 700 Personal Monitor Systems; or
packaged with Shure's PSM 400 Hardwired and Wireless Performance Packs.
Installed Sound Systems
The P4M can also be used as a small "piggyback" mixer in applications such as houses of worship, or courtrooms.
The unit acts as a console bypass when a permanent installation of a large, operator-controlled mixing console may
require just a few microphones for smaller events. This allows the user easy access and control of up to four signals
without having to utilize the larger console. Given its dual-bus output capabilities, the P4M can also serve as a "two zone"
mixer, routing any combination of mic or line-level signals to two different zones.
More Than Four Inputs
The P4M has a pair of 1/4-inch auxiliary inputs that can be used to add channels from other sources. For example
multiple P4M mixers can be linked together to increase the number of inputs. In addition, sources not present in the original
mix - such as a click track for live percussion - may be included via the auxiliary inputs.
Measurement Conditions (unless otherwise specified):
full gain; 1 kHz, one channel activated; >source impedances: Mic 150 ohms, Aux Level 150 ohms; terminations: Line 600 ohms.
Frequency Response (Ref 1 kHz, controls centered)
20 Hz to 20 kHz +/- 2 dB
Input Specifications
Input
1-4 (front panel) Aux In
Gain (Maximum) 43 dB 0 dB
Impedance (at 1 kHz) 5800 ohms 18 kilohm (each)
9100 ohms (1/L mono)
Input Clipping Level +12 dBV +12 dBV
Crosstalk -100 dB -90 dB
Common Mode Rejection > 75 dB > 70 dB
Output Specifications
Output
Split 1-4 Mix Out
Impedance N/A 500 ohm (unbalanced)
1 kilohm (balanced
Output Clipping Level N/A +5 dBV (10 kilohm balanced
load, -30 dBV input ch. 1-4)
Noise (100 Hz to 22 kHz) -110 dBV -100 dBV (all controls CCW)
-62 dBV (all controls CW)
Distortion (THD) at 1 kHz .0005% |
With the AKG MDAi CPA Connected PA microphone adapter, all your favorite dynamic vocal mics instantly become part of the HARMAN Connected PA system. Simply attach the device to any input of your Soundcraft Ui24r mixer and then plug-in your dynamic mic and mic cable for automatic recognition with the HARMAN Connected PA app and ecosystem?providing effortless set up, instant recall of performer and presets, and great sound for musicians of all skill levels.
Current products with embedded ioSYS technology and HARMAN Connected PA compatibility include the Soundcraft Ui24R mixer, JBL PRX800W loudspeakers, dbx Di1 direct boxes, and AKG P5i microphones. |
Reviews
There are no reviews yet.