BIAMP PM-1122 Stereo Pre-amp

The PRE-73 MKIII is a one-channel vintage style microphone-, line- and instrument preamplifier. The signal path uses only discrete components like resistors, capacitors and transistors. The in- and output is transformer balanced, using two different transformers, each one optimized for its purpose. This is the way audio components were built before integrated circuits became available.

The circuit used in the PRE-73 MKIII is similar to the preamp section in the classical 1073 module with a corresponding sound character that is warm, punchy, sweet and musical. These classic characteristics have been heard on countless recordings through the years and it is a versatile sound that works very well on most sound sources and in most genres.
The essence of this sound is now available at a surprisingly low cost, making it available to nearly everyone.

Features  :

• Vintage Style electronics. No intergrated circuits in the signal path.

• Maximum gain in MIC mode is 80 dB, enough to handle passive ribbon mics with quiet sound sources.

• GAIN switch range 20 - 80 dB. GAIN/LINE mode switch, gain is reduced by 30 dB in LINE mode.

• Selectable two position high frequency AIR boost eq, 3 or 6 dB @ 30 kHz.

• Selectable 6 dB/octave two frequency high pass filter at around 40 (HP1) and 170 Hz (HP2).

• Tantalum capacitors in the signal path.

• Switchable impedance in MIC mode, 1200 or 300 Ohms, will change the tone of most mics. The input impedance in LINE mode is 10 kohm.

• Switchable phantom power and absolute phase.

• A high-impedance instrument input for any sound module, electric guitar or bass.

• A simple but effective 4-step LED output level meter.

• The output level control makes it possible to make fine gain adjustments and also to overload the main gain stage(s) for more character and then lower the signal to a suitable level before the output stage.

• Combo XLR/TRS input jack and separate output XLR and TRS jacks for flexible connections.

• Insert jack for inserting EQ´s and other units.

• Selectable 600 ohm output termination.

• The pcb is prepared for the Carnhill input transformer.

• External power supply to avoid interaction with the audio circuits and transformers.

• A solid build quality that will last many years of normal use.

The MKIII has the following new features compared to the MKII:

• Tantalum capacitors in the signal path.

• Selectable two position high frequency AIR boost eq, 3 or 6 dB @ 30 kHz.

• Selectable two frequency high pass filter, 6 dB/octave at 40 or 170Hz.

• The pcb is prepared for the Carnhill input transformer.

• Revised and less complicated GAIN switch with a separate switch for MIC/LINE selection.

• All GAIN settings can also be used in LINE mode .

The U5 high-voltage DI-preamp combines a unique passive tone selector with a variable
gain preamp and filter. The high input impedance accepts a wide variety of signal levels
and instruments from acoustic guitars to high-output active bass guitars and keyboards.
The U5 direct box is loaded with sonic character and user features professionals demand.

U5 FEATURES
Pure Class A, 100% discrete design
Smooth musical detail and sonic excellence
Variable gain preamp to +30dB.
Dual microphone and line outputs
Hi-Z   3,000,000 ohm input impedance
Very low noise -100dB
High headroom +30dB
Six tone bank selections.
DC coupled Class A output for superior bass
High cut switch eliminates noise
LED active signal indicator
Headphone monitor output jack
Low distortion less than 0.5% THD and IMD
High level 400 watt speaker input
Active to thru selector - ground isolation switch
100% discrete power supplies for audio path
Internal toroidal power supply for low noise
Long lasting, stainless steel hardware
 
SONIC EXCELLENCE
The Avalon U5 Pure Class A instrument DI & preamplifier is the most powerful direct box
available today.  Designed to optimize absolute signal integrity and musical performance,
the U5 includes many features and sonic excellence unequaled by lesser designs. The
U5 is ideal for bass guitar and acoustic instruments, electric guitars, keyboards, synthesizers
and low output pickups. 
Features include state-of-the-art, high input impedance input stage for zero load effect on
sensitive pickups and keyboards, 100% discrete, Pure Class A signal amplifiers, practical
user features and rugged hardware designed to deliver true high performance audio for many
years. 
DESIGNED FOR DEEP & CONTROLLED BASS
Avalon U5 DI-preamps have been in use around the world since 1995. They have found their way
into the world's leading musicians rigs and recording sessions and been featured on thousands
of the best selling (and sounding) albums and live performances.
MINIMUM SIGNAL PATH DESIGN
The U5 includes a variable gain Class A preamplifier to boost low level pickup signals and a high
level speaker input for capturing the live sound of the instruments amplifier. Six passive tone-EQ
curves are also included to enhance a variety of acoustic and electric instruments. A high-cut switch
eliminates unwanted acoustic pickup and high frequency noise, while a  headphone monitor amp
has been included for personal listening. Twin DC coupled Class A output amplifiers drive both low
level microphone preamp inputs and high level +4dB inputs for direct to tape recording or processing.
The active-to-thru switch selects either the instrument input directly or sends the boosted-equalized
signal to the amplifier via the front panel jack. A ground isolation switch eliminates any possible earth
loop or AC buzz problems with complete safety.

U5 SPECIFICATIONS
Circuit Topology:  100% discrete, high-voltage Class A 
Gain:  Switched 3dB steps, maximum gain +30dB 
Input Impedance:  3 ,000,000 ohm unbalanced (single ended) 
Maximum Input Level  +24dBu unbalanced, 400w speaker input 
Output Connectors (2):  XLR type, pin 2 hot electronic balanced 
Maximum Output Level (Class A):  +30dBu DC coupled, balanced 600 ohms (mic and line out) 
Headphone Output:  0.5w into 600 ohms 
Noise 20kHz Unweighted:  -100dBu minimum gain position 
Distortion THD, IMD:  0.1% at +10dB 
Frequency Response, -/+0.5dB:  5Hz to 100kHz 
Frequency Response, -3dB:  1Hz to 500kHz (input band limited) 
High Cut Filter:  -3dB at 8kHz minimum phase design 
Tone Selector:  Six position rotary switch, all passive filters 
AC Power:  Internal toroidal AC supply 
Dimensions:  8.5 x 3.5 x 12 in (216 x 88 x 305mm) 
Weight-Packed:  12lbs (5.4kg) 
Rack mount kit (1) RM-1:  Single U5 19 inch rack mount kit (holds one half rack unit) 
Rack mount kit (2) RM-2:  Dual U5 19 inch rack mount kit (holds two half rack units) 

The PreSonus HP60 is the most flexible and advanced headphone amplifier system available for professional and project recording studios as well as live sound in-ear monitoring systems. Loaded with six independent,
loud and clear headphone amplifiers, the HP60 features dual stereo inputs as well as external input, for each
channel allowing you to mix between three stereo audio streams (mix A, mix B, and external input). Stereo output is also available on each channel to send line level headphone channel mixes to additional headphone amplifiers or monitor systems. Each channel features headphone level, mix control between A and B inputs, external input volume, mute and mono. The HP60 also features talkback via external XLR microphone input. Common set up of the HP60 in a recording session is to send the main control room mix to input A. Send the click track to input B. Send the each band member direct recording input to each channelʼs external input (more me). This will allow each band member to create a mix between the main mix, the click track and themselves. The HP60 is the ultimate headphone amplification system delivering loud and clear headphone mixes for real-world recording situations.

Features:
-Six independent ultra low noise, high output headphone amplifiers (150 mW per channel)
-Two sets of stereo inputs (A and B) with balanced TRS connectors
-Stereo external input point on each channel for "more me” with trim control
-Mix control between inputs A and B
-Talkback with external XLR microphone with control
-Direct stereo line output on each channel

Having had great success with the PRE-73 preamp, we have received many requests for a version for the 500 eries rack format. We are therefore happy to present the PRE-573, expected to start shipping in late September.
 
The PRE-573 is a one width module that has the sound and the features that made the PRE-73 so successful and a few additional ones.
The circuit still uses the preamp and output section from the classic 1073-module, adapted to work in the api rack format. It has a total  gain range from -15 to +80 dB. The 10 - 70 dB range is handled by a turn switch  and there is a separate toggle switch to select an additional 5 or 10 dB gain. The input can be configured to accept line level signals by another switch, the gain is then lowered by about 25 dB and the input impedance increased to about 15 kohm.
 
The input impedance of the mic input mode can be switched between 1200 and 300 ohm. Phantom power and phase reverse is also selectable by front panel switches.
 
An added feature, using the same circuit as in the PRE-73 DLX, is the active DI-input with a high input impedance of about 1,5 Mohm. The output signal from the active DI circuit passes through the input transformer for some extra character.
The DI-input is very flexible since it can be changed to a purely passive one by a front panel switch. The DI input is then exactly the same as in the PRE-73 Mk2 where the signal is feed directly into the second gain stage, bypassing the transformer and with an input impedance of about 100 kohm.

These two DI-options makes it possible to get different tones from electric instruments and the passive DI input mode is more suited for injecting active units like sound modules. 
 
A new feature is the switchable AIR mode that  adds a small boost above 10 kHz that peaks at 2 dB at about 35 kHz.

A simple but effective signal and overload indicator is offered by a single LED that starts glowing red at about +4 dBu and then increases its intensity up to the maximum output level.
 
The PRE-573 has a dedicated insert connector at the back allowing it to interface with other GAP 500 modules. The insert can be activated by removing a jumper connector at the back of the module.
The second Golden Age Project module for the api 500 rack will be the EQ-573, expected to ship in November 2012. The EQ-573 consists of the inductor based high pass filter section  and the 3-band eq section from the classic 1073 module with some added frequencies. These two modules together will offer a fully fledged 1073-module in a compact format at a very low cost.
 
There is a second jumper at the back of the module that selects 600 ohm termination on the output. The standard mode is termination on, since it gives the flattest response when the PRE-573 is used with modern line inputs that typically has an input impedance of 10 kohm or more. The user can chose to remove the jumper and deactivate the termination resistor, this will increase the level above 10 kHz and create a peak in the response for an even more pronounced  "Air" effect.
The output is transformer balanced and fully floating and can drive a 600 ohm load up to level of about 28 dBu.

Designed for high-definition field production environments, the studio-quality MP-1 is an ideal line-driver for critical radio, television, and film applications.

The MP-1 is extremely durable and easy to use. With rugged mechanical and electrical construction and high-quality components it will provide years of superb audio performance under the most punishing field conditions.

• Superb audio specifications
• 66 dB of gain, in eleven discrete steps
• Transformer-balanced input and output
• Phantom power - 48 volt or 12 volt
• High pass filter @  80 Hz or 160 Hz, 6 dB/octave
• Limiter makes unit virtually "unclippable“
• High current line output drive
• Excellent immunity to RF interference.
• Battery power (two x AA)
• Durable mechanical construction