| Content | Digital Sound 8928 SPL Meter with Built-In Measurement Mic - calibrated from 300Hz to 8kHz (+/-2dB), 4 control zones in 10dB steps (40-130dB), large LCD display, peak-hold, fast/slow display modes, includes 9V battery.
A superbly designed easy to use sound level meter with features normally only found on more expensive instruments. It has an electret condenser microphone giving virtually instant readings updated every 0.5 seconds on an extra large LCD display.
- 4 measuring ranges, 40 to 70dB, 60 to 90dB, 80 to 110dB or 100 to 130dB
- 0.1dB resolution updated every 0.5 seconds
- Auto ranging or manual range selection
- ʽAʼ & ʽCʼ frequency weighting
- Fast or slow response filters
- 42mm LCD display with quasi-analogue bargraph and function Indicators
- Bargraph in 1dB steps updated every 40ms
- Max hold function to display the highest recorded value
- Min/max memory since power on or last reset
- Low battery indicator
- Auto power off
- Analogue output AC: 0.707 Vrms (at full scale)
- Supplied with battery
|
The MiniSPL is the perfect accessory to the Acoustilyzer & Minilyzer for
acoustical measurements.
The MiniSPL is a battery powered measurement microphone. Together
with the Acoustilyzer or Minilyzer, it forms an acoustical analyzer and integrating
sound level meter. Additionally it may be operated as a stand-alone microphone
e.g. connected to a balanced audio-line, a microphone-input or a sound-card.
Product-details
? Battery powered
? Factory-set sensitivity
? No phantom power required
? 1/2" microphone, class 2 acc. IEC 61672
? Omni-directional
? Supplied with mic clamp, wind protection
? Typical frequency response included
MiniSPL together with Acoustilyzer:
? SPL Meter / RTA
? Reverberation Time RT60
? Delay Time
? FFT Analyzer
? Speech Intelligibility STI-PA
MiniSPL together with Minilyzer:
? Measurements: SPL, min./max., Leq
? 1/3rd octave spectrum analyzer |
Palmer Pro MCT DMX 3-pin and 5-pin DMX and XLR cable tester
MCT DMX
This cable tester checks 3-pin and 5-pin DMX cables for continuity in fully automatic or manual pin selection modes. Pin connection status of the male and female cable ends is indicated by two rows of bright LEDs. In addition, the unitʼs 3-pin connectors can also be used to test XLR microphone cables. The DMX Cable Tester comes with two L-brackets for variable mounting options.
- Tests 3-pin and 5-pin DMX cables for continuity
- Also tests 3-pin XLR microphone cables
- Automatic test mode or manual pin 1 - 5 selection
- LED indicators
- Mounting brackets included
Product type
Test Equipment
Connectors
XLR (3-pin) , XLR (5-pin)
Controls
Auto Scan , On / Off , Scan switch
Indicators
LED chain
Operating voltage
2 x AA battery
Acoustic continuity test
no
Test cable
no
Cabinet material
sheet steel
Cabinet surface
powder coated
Width
240.2 mm
Height
48 mm
Depth
53 mm
Weight
0,7 kg
| With the PAN05, two microphone signals can be mixed down to one. Since decoupling occurs via the balanced resistor network, the PAN05 also lets phantom power "pass through“, useful for condenser microphones. However, due to the difference in sound and signal level, mixing dynamic and condenser mics should be avoided. Best results will be achieved using two identical mics.
SPECIFICATIONS:
- Input: 2 x XLR/f balanced
- Nominal impedance: 200 Ω
- Output 1 x XLR/m balanced
- Load impedance >200 Ω
- Symmetrically decoupled through resistors
- Total ohmic value: 200 ohms
- Typical attenuation: 6 dB
- Housing: metal casing 110 x 73 x 42 mm
|
- Microprocessor-controlled cable tester featuring 3 modes: cable and installed cable test plus test tone mode
- Accepts all standard connectors: XLR, Speakon*, TRS (1/4“, 1/8“), RCA, RJ45, MIDI and USB
- Super-easy operation with intuitive LED display
- Continuity check and intermittent contact detection
- Phantom-power and ground-shield check
- Test-tone generator: 1 kHz or 440 Hz at +4 dBu, -10 dBV or -50 dBV
- Operates with 2 AA size batteries (not included)
- Designed and engineered in Germany
|
This is an on-the-road tool you certainly can't miss in your gearbox! A nifty, handy cabletester, which allows you to check up to six (welding) connections and gives you a visual readout by 2 rows of 6 LED's. The checking itself is done manually per connected pin. A LED will light up to indicate what pin is connected correctly on which side. A short-circuit check with a red LED and audio-warningsignal is also included. On the left and right side you'll find inputs for 6,3 symm. jack, BNC, RCA, 5p. DIN, 5p. XLR, 3p. XLR and Neutrik® Speakon®.
|
Reviews
There are no reviews yet.