Content |
Analog Inputs Modular
Analog Outputs Modular
Audio Network CobraNet CM-1 Module (optional)
Cooling Left-to-right, 3-stage fan
Data Format 24 Bit linear A/D and D/A conversion, 48 Bit processing
Digital Inputs Modular
Digital Outputs Modular
FIR-Drive Yes
GPIO Control Port 2 x 6-pole Euro block4 Control Inputs (analog 0 - 10 V / logic control) 3 Control Outputs (Relay contact to ground) 1 Fault Output (NC Relay contact)3 Reference Outputs (+5 V / +10 V/ GND)
Internal Processing 2 DSPs Standard (150 MHz, 300 MIPS), DSP-2 Extension Module (3 dual core processors-1200 MIPS total) , 1 DSP per Audio Module (100 MHz, 100 MIPS) 1500 MIPS total without I/O cards
Network Control (IRIS-Net) Yes
Network Interface Ethernet-10/100 MBit/s, RJ-45
Power Consumption 90 W max. (incl. 2 x AI-1, 2 x AO-1, 1 x CM-1 modules)
Power Supply 100 - 240 VAC, 50/60 Hz
Sample Rate 48 kHz internal
Serial Interface 2 Ports, 9pin D-Sub female (Remote Control)
Signal-to-Noise Ratio (A-weighted) 115 dB
Total Harmonic Distortion 0.01 %
Height 2RU 88.1 mm (3.47“)
Width 483 mm (19.02“)
Depth 381 mm (15“)
Weight Net 7.37 kg (16.25 lbs)
|
CobraNet is a network technology for multichannel transmission of digital audio data. The CM-1 is a compact interface module for NetMax to allow connection to a CobraNet network, which allows the simultaneous transmission of up to 32 digital audio input signals and 32 digital audio output.
* Designed for Cinema, Club Sound, Commercial Sound/Life Safety, Concert Sound, House of Worship, Performance & Sports Venues, Stadium Systems, and other applications.
* 100BASE-TX ethernet interface; 100Mbit/s full-duplex Ethernet interface; IEEE 802.3u compatible.
* Secondary 100BASE-TX Ethernet interface. Second Ethernet interface for the connection of a redundant network to establish fault tolerant systems. Internal audio output interface for the transmission of 32 digital audio channels with 48 kHz sample rate and 16, 20, or 24-bit word length
* Internal audio input interface for receiving 32 digital audio channels with 48 kHz sample rate and 16, 20, or 24-bit word length.
* Control, monitoring, configuration, and firmware updates via Ethernet protocol.
* Status LEDs. Link, activity, fault, and CobraNet conductor status indication via Ethernet connectors.
|
The ZonePRO 640m offers fixed I/O, pre-configured architecture, configurable insert processing and optional duplication of audio channels to another ZonePRO device via a link bus.
The 640m features a total of six inputs and four outputs. Inputs include four balanced mic/line switchable terminal block inputs and two mono-summed pairs of unbalanced RCA inputs. Hardware-controlled microphone gain allows adjustment of microphone gain per channel.
The 640m device has a pre-configured architecture with input processing, a central matrix and output processing. Two input insert positions and one output insert position allow channel-specific insert processing to be configured. AutoWarmth®, a psychoacoustic function that maintains full frequency bandwidth even when the signal level has dropped, is permanently available on each output zone.
A link bus allows duplication of the first six audio channels to another ZonePRO device in applications where additional output zones are required.
The front panel of the 640m features comprehensive signal metering, an informative LCD display and user-specified front panel control.
Additional system control is offered in the form of optional Zone Controllers. This collection of hardware wall-controllers represents a series of simple, elegant user interfaces for functions such as volume, source and preset control.
All ZonePRO devices can be controlled by third party control systems via RS-232 or Ethernet as applicable (see table for further information).
ZonePRO Designer—the configuration, control and monitoring software for the ZonePRO family of devices—offers control of the ZonePRO 640m via Ethernet or RS-232. The Configuration Wizard within ZonePRO Designer guides users through the step-by-step configuration process of the 640m.
Front Panel LED Indicators
Per Output:4 Independent Six-Segment Lightpipe Output Meters that range from -30 to +20 dBu, Threshold Meters
Other:LCD Display provides information about Source Selection, Page Steering, Zone Volume and Mute
Analog Inputs:
6 Total (4) Switchable Mic or Line, (2) Unbalanced, Mono-Summed RCA Input Pairs
Type:Euroblock (Mic/Line), RCA (Source)
Impedance (Euroblock):>50kΩ Balanced, >25kΩ Unbalanced, RF Filtered
Impedance (RCA):>25kΩ Unbalanced, RF Filtered
Max. Input Line Level:+20dBu Mic/Line, +12dBu RCA
CMRR:> 40dB, typically >55db @ 1kHz
Mic Pre Gain:30 to 60dB
Mic Input Noise (E.I.N.):
Mic Phantom Power:+15VDC
ANALOG OUTPUTS
Number of Outputs: 4 Total
Type:Electronically Balanced, RF Filtered Euroblock
Impedance:120Ω Balanced, 60Ω Unbalanced
Max. Output Level:+20dBu
A/D PERFORMANCE
Type: dbx Type IV™ Conversion System
Dynamic Range line: >113dB, A-weighted, >110dB unweighted
Type IV dynamic range:
>119dB, A-weighted, 22kHz
BW: >117dB, unweighted, 22kHz BW
Sample Rate: 48kHz
D/A PERFORMANCE
Dynamic Range: 112dB A-weighted, 109dB unweighted, 22kHz BW
SYSTEM PERFORMANCE
Dynamic Range: >109dB A-weighted, >106dB unweighted, 22kHz BW
THD+N: 0.003% typical at +4dBu, 1kHz, 0dB gain
Frequency Response: 20Hz – 20kHz, +/- 0.5dB
Interchannel Crosstalk: >80dB typical
Crosstalk input to
output: >80dB
Propagation Delay 0.6 msec
POWER REQUIREMENTS
Operating Voltage: 100 VAC, 50/60Hz, 120 VAC, 60Hz, 230VAC 50/60Hz
Power Consumption: 29 Watts
BTU: | 8-ZONE MUSIC AND ANNOUNCEMENT CONTROL SYSTEM ZONE8 is PROEL's answer for general or zone-selectable announcements and program material. It can manage up to 8 zones and can be configured to use a single amplification system for program material and announcements, or separate amplification for each. The ZONE8 accepts input from up to 18 different microphone control bases connected through a CAT5 interface, can be configured to accept announcement input from telephones through the internal exchange, and can be easily interfaced with alarm systems.
Main features: - 5 selectable program material inputs: Tape, CD, Tuner, AUX1, AUX2 - Level control for announcement inputs - Program material level control - Program material routing selectors for each zone - 'BUSY' LED indicators for active announcements in each zone - Priority microphone input for emergency announcements. |
- 8ch mic/line input and 8ch analog output
- 16ch YDIF digital I/O
- 16ch Dante digital I/O
- 1x MY Card slot
- SD Card Slot for playback
|
Intelligent Control Panel, Wall-mountable.
The ICP1 intelligent control panel features controls virtually identical to those on the DME64N/DME24N
front panels, giving operators remote control capabilities for both DMEs. It offers unmatched ease of use
thanks to a large, easy-to-read backlit LCD display that shows names for scenes and function keys in 5
languages – Japanese, English, French, German and Spanish. The 6 function keys appearing at the top
and bottom of the LCD screen can be assigned to most parameters for easy remote control access.
These function keys are defined as a "function key set" or "page“. Up to 4 sets of "pages" are available –
for up to 24 parameters assignable to function keys. Users can change the "page" by pressing the
HOME key. A single function key can be used for simultaneous multiple parameter control by defining
parameter links. Function keys are defined with DME Designer software. |
Reviews
There are no reviews yet.